wheel torque YAMAHA TTR50 2006 Owners Manual

SPEC
2 - 13
NOTE:
1.First, tighten the ring nut approximately 38 Nm (3.8 m · kg, 27 ft · lb) by using the lower ring nut
wrench and turn the steering right and left a few times; then loosen the lower ring nut completely.
2.Retighten the lower ring nut 4 Nm (0.4 m · kg, 2.9 ft · lb).
Part to be tightened Thread size Q
’ty Tightening torque
Nm m ·kg ft ·lb
Engine mounting: Engine and frame (front upper side) M8 × 1.25 1 30 3.0 22
Engine and frame (rear upper side) M8 × 1.25 1 30 3.0 22
Engine and frame (rear lower side) M10 × 1.25 1 48 4.8 35
Engine bracket and frame M8 × 1.25 2 30 3.0 22
Front wheel axle and front wheel axle nut M12 × 1.25 1 35 3.5 25
Front brake camshaft lever and front brake
camshaft M6
× 1.0 1 7 0.7 5.1
Front brake cable locknut M8 × 1.25 1 16 1.6 11
Front wheel nipple (spoke) —28 2 0.2 1.4
Rear wheel nipple (spoke) —28 2 0.2 1.4
Rear wheel axle and rear wheel axle nut M12 × 1.25 1 60 6.0 43
Rear brake camshaft lever and rear brake
camshaft M6
× 1.0 1 7 0.7 5.1
Rear wheel drive hub and rear wheel sprocket M8 × 1.25 4 25 2.5 18
Drive chain puller locknut M6 × 1.0 2 7 0.7 5.1
Upper bracket and handlebar M10 × 1.25 2 32 3.2 23
Steering stem nut M22 × 1.0 1 110 11.0 80
Lower ring nut M25 1 Refer to NOTE.
Upper bracket and lower bracket M10 × 1.25 2 32 3.2 23
Inner tube assembly and front fork guard M6 × 1.0 4 7 0.7 5.1
Pivot shaft and nut M10 × 1.25 1 35 3.5 25
Rear shock absorber and frame M10 × 1.25 1 30 3.0 22
Rear shock absorber and swingarm M10 × 1.25 1 30 3.0 22
Drive chain guide and swingarm M6 × 1.0 2 7 0.7 5.1
Drive chain support and swingarm M6 × 1.0 3 7 0.7 5.1
Drive chain guard and swingarm M6 × 1.0 2 7 0.7 5.1
Upper bracket and front fender M6 × 1.0 2 7 0.7 5.1
Fuel tank and fuel cock M6 × 1.0 2 7 0.7 5.1
Fuel tank and frame M6 × 1.0 2 7 0.7 5.1
Air scoop and fuel tank M6 × 1.0 2 7 0.7 5.1
Seat assembly and frame M6 × 1.0 2 7 0.7 5.1
Seat and rear fender M6 × 1.0 3 7 0.7 5.1
Seat and side covers M6 × 1.0 4 7 0.7 5.1
Footrest, under cover and engine M8 × 1.25 4 30 3.0 22
Sidestand and sidestand bracket M10 × 1.25 1 40 4.0 29
MAINTENANCE SPECIFICATIONS