engine YAMAHA TZR50 2008 User Guide

EAU13561
Fuel cock
1. Fuel cock
The fuel cock supplies fuel from the
tank to the carburetor while filtering it
also.
The fuel cock has three positions:
OFF
With the lever in this position, fuel will
not flow. Always return the lever to
this position when the engine is not
running.
ON
With the lever in this position, fuel
flows to the carburetor. Normal riding
is done with the lever in this position.RES
This indicates reserve. If you run out
of fuel while riding, move the lever to
this position. Fill the tank at the first
opportunity. Be sure to set the lever
back to “ON” after refueling!
EAU13590
Starter (choke) lever “q”
1. Starter (choke) lever
Starting a cold engine requires a
richer air-fuel mixture, which is sup-
plied by the starter (choke).
Move the lever in direction (a) to turn
on the starter (choke).
Move the lever in direction (b) to turn
off the starter (choke).
j
k1(b)
(a)1
ON
RES OFFFUEL
3
INSTRUMENT AND CONTROL FUNCTIONS
3-8
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 8

EAU15301
Sidestand
1. Sidestand
The sidestand is located on the left
side of the frame. Raise the sidestand
or lower it with your foot while holding
the motorcycle upright.
NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system,
which cuts the ignition in certain
situations. (See further down for an
explanation of the ignition circuit cut-
off system.)
EWA10240
s s
WARNING
The vehicle must not be ridden with
the sidestand down, or if the sides-
tand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control. Yama-
ha’s ignition circuit cut-off system
has been designed to assist the
operator in fulfilling the responsibi-
lity of raising the sidestand before
starting off. Therefore, check this
system regularly as described
below and have a Yamaha dealer
repair it if it does not function pro-
perly.
EAU15311
Ignition circuit cut-off
system
The ignition circuit cut-off system
(comprising the sidestand switch,
clutch switch and neutral switch) has
the following functions.
It prevents starting when the
transmission is in gear and the
sidestand is up, but the clutch
lever is not pulled.
It prevents starting when the
transmission is in gear and the
clutch lever is pulled, but the
sidestand is still down.
It cuts the running engine when
the transmission is in gear and
the sidestand is moved down.
Periodically check the operation of
the ignition circuit cut-off system
according to the following procedure.
EWA10250
s s
WARNING
If a malfunction is noted, have a
Yamaha dealer check the system
before riding.
1
3
INSTRUMENT AND CONTROL FUNCTIONS
3-10
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 10

3
INSTRUMENT AND CONTROL FUNCTIONS
3-11
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.
Does the engine start?
With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.
Does the engine stall?
After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.
Does the engine start?
The system is OK. The motorcycle can be ridden.
This check is most reliable if performed with
a warmed-up engine.
The neutral switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
The sidestand switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
The clutch switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
YES NO YES NO YES NONOTE:
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 11

EAU15603
Pre-operation check list
4
PRE-OPERATION CHECKS
4-2
ITEM CHECKS PAGE
• Check fuel level in fuel tank.
Fuel• Refuel if necessary. 3-5, 3-6, 3-7
• Check fuel line for leakage.
• Check oil level in oil tank.
2-stroke engine oil• If necessary, add recommended oil to specified level. 3-7
• Check vehicle for oil leakage.
Transmission oil• Check oil level in transmission case.
• If necessary, add recommended oil to specified level.6-8
• Check coolant level in reservoir.
Coolant• If necessary, add recommended coolant to specified level. 6-9
• Check cooling system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Front brake• Replace if necessary. 3-5, 6-17 ~ 6-20
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Rear brake• Replace if necessary. 3-5, 6-17 ~ 6-20
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
Clutch• Lubricate cable if necessary.
3-4, 6-16, 6-24
• Check lever free play.
• Adjust if necessary.
• Make sure that operation is smooth.
Throttle grip• Check cable free play.
6-12, 6-23
• If necessary, have Yamaha dealer adjust cable free play and lubricate
cable and grip housing.
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 13

ITEM CHECKS PAGE
Control cables• Make sure that operation is smooth.
• Lubricate if necessary.6-23
• Check chain slack.
Drive chain• Adjust if necessary.
6-21, 6-22
• Check chain condition.
• Lubricate if necessary.
• Check for damage.
Wheels and tires• Check tire condition and tread depth.
6-14, 6-16
• Check air pressure.
• Correct if necessary.
Brake and shift pedals• Make sure that operation is smooth.
• Lubricate pedal pivoting points if necessary.3-4, 3-5, 6-24
Brake and clutch levers• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.3-4, 3-5, 6-24
Sidestand• Make sure that operation is smooth.
• Lubricate pivot if necessary.3-10, 6-25
Chassis fasteners• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.—
Instruments, lights, signals • Check operation.
and switches• Correct if necessary.—
Engine stop switch• Check operation.3-3
Sidestand switch• Check operation of ignition circuit cut-off system.
• If system is defective, have Yamaha dealer check vehicle.3-10
4
PRE-OPERATION CHECKS
4-3
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 14

EAU15950
EWA10270
s s
WARNING
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or func-
tion that you do not thoroughly
understand.
Never start the engine or ope-
rate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of cons-
ciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised comple-
tely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAU16050
Starting a cold engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
s s
WARNING
Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-11.
Never ride with the sidestand
down.
1. Turn the fuel cock lever to “ON”.
2. Turn the key to “
f” and make
sure that the engine stop switch
is set to “
f”.
3. Shift the transmission into the
neutral position.
NOTE:
When the transmission is in the neu-
tral position, the neutral indicator lightshould be on, otherwise have a
Yamaha dealer check the electrical
circuit.
4. Turn the starter (choke) on and
completely close the throttle.
(See page 3-8.)
5. Start the engine by pushing the
start switch.
NOTE:
If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the
engine more than 10 seconds on any
one attempt.
ECA11410
CAUTION:
The 2-stroke engine oil level war-
ning light should come on when the
start switch is pushed, and it
should go off when the start switch
is released. If the warning light flic-
kers or remains on after starting,
immediately stop the engine, and
then check the 2-stroke engine oil
level and the vehicle for oil leakage.
5
OPERATION AND IMPORTANT RIDING POINTS
5-1
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 1

If necessary, add 2-stroke engine
oil, and then check the warning
light again. If the warning light does
not come on when pushing the
start switch, or if it does not go off
after starting with sufficient 2-stro-
ke engine oil, have a Yamaha dealer
check the electrical circuit.
6. After starting the engine, move
the starter (choke) back halfway.
ECA11040
CAUTION:
For maximum engine life, never
accelerate hard when the engine is
cold!
7. When the engine is warm, turn
the starter (choke) off.
NOTE:
The engine is warm when it responds
normally to the throttle with the starter
(choke) turned off.
EAU16640
Starting a warm engine
Follow the same procedure as for
starting a cold engine with the excep-
tion that the starter (choke) is not
required when the engine is warm.
EAU16671
Shifting
1. Shift pedal
Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing
hills, etc.
The gear positions are shown in the
illustration.
NOTE:
To shift the transmission into the neu-
tral position, press the shift pedal
down repeatedly until it reaches the
end of its travel, and then slightly rai-
se it.
6
5
4
3
2
N
1
1
5
OPERATION AND IMPORTANT RIDING POINTS
5-2
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 2

ECA10260
CAUTION:
Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long
distances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.
Always use the clutch while
changing gears to avoid dama-
ging the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.
EAU16800
Tips for reducing fuel
consumption
Fuel consumption depends largely on
your riding style. Consider the follo-
wing tips to reduce fuel consumption:
Turn the starter (choke) off as
soon as possible.
Shift up swiftly, and avoid high
engine speeds during accelera-
tion.
Do not rev the engine while shif-
ting down, and avoid high engine
speeds with no load on the engi-
ne.
Turn the engine off instead of let-
ting it idle for an extended length
of time (e.g., in traffic jams, at
traffic lights or at railroad cros-
sings).
EAU16830
Engine break-in
There is never a more important
period in the life of your engine than
the period between 0 and 1000 km
(600 mi). For this reason, you should
read the following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1000 km (600 mi). The various parts in
the engine wear and polish themsel-
ves to the correct operating clearan-
ces. During this period, prolonged
full-throttle operation or any condition
that might result in engine overhea-
ting must be avoided.
EAU17130
0~500 km (0~300 mi)
Avoid prolonged operation above
4.000 r/min.
After every hour of operation, stop the
engine, and then let it cool for five to
ten minutes.
Vary the engine speed from time to
time. Do not operate the engine at
one set throttle position.
5
OPERATION AND IMPORTANT RIDING POINTS
5-3
5WX-F8199-E2.qxd 13/9/06 10:58 Página 3

500~1000 km (300~600 mi)
Avoid prolonged operation above
6.000 r/min.
Rev the engine freely through the
gears, but do not use full throttle at
any time.
ECA10370
CAUTION:
After 1000 km (600 mi) of operation,
the transmission oil must be chan-
ged.
1000 km (600 mi) and beyond
The vehicle can now be operated nor-
mally.
ECA10310
CAUTION:
Keep the engine speed out of
the tachometer red zone.
If any engine trouble should
occur during the engine break-
in period, immediately have a
Yamaha dealer check the vehi-
cle.
EAU17180
Parking
When parking, stop the engine, remo-
ve the key from the main switch, and
then turn the fuel cock lever to “OFF”.
EWA10310
s s WARNING
Since the engine and exhaust
system can become very hot,
park in a place where pedes-
trians or children are not likely
to touch them.
Do not park on a slope or on
soft ground, otherwise the
vehicle may overturn.
ECA10380
CAUTION:
Never park in an area where there
are fire hazards such as grass or
other flammable materials.
5
OPERATION AND IMPORTANT RIDING POINTS
5-4
5WX-F8199-E2.qxd 13/9/06 10:58 Página 4

ODOMETER READING (x 1000 Km)
ANNUAL
NO ITEM CHECK OR MAINTENANCE JOB
1 6 12 18 24CHECK
• Check tread depth and for damage.
9*Tires• Replace if necessary.
√√√√ √
• Check air pressure.
• Correct if necessary.
10 *Wheel bearings• Check bearing for looseness or damage.√√√√
11 *Swingarm• Check operation and for excessive play.√√√√• Lubricate with lithium-soap-based grease. Every 24000 km
• Check chain slack, alignment and condition.
Every 500 km and after washing
12Drive chain• Adjust and lubricate chain with a special O-ring chain
lubricant thoroughly.the motorcycle or riding in the rain
13 *Steering bearings• Check bearing play and steering for roughness.√√ √ √√• Lubricate with lithium-soap-based grease. Every 50000 km
14 *Chassis fasteners• Make sure that all nuts, bolts and screws are properly
tightened.√√√√ √
15Sidestand• Check operation.
• Lubricate.√√√√ √
16 *Sidestand switch• Check operation.√√ √ √√ √
17 *Front fork• Check operation and for oil leakage.√√√√
Rear suspension relay • Check operation.√√√√
18 *arm and connecting arm
pivoting points• Lubricate with lithium-soap-based grease.√√
19 *Carburetor• Check starter (choke) operation.
• Adjust engine idling speed.√√ √ √√ √
20 *Autolube pump• Check operation.
• Bleed if necessary.√√√√
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-3
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 3