engine oil YAMAHA TZR50 2008 User Guide

ECA11110
CAUTION:
Do not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.
EAU23100
Checking and lubricating the
cables
The operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends should
be lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or repla-
ce it.
EWA10720
s s
WARNING
Damage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.
EAU23111
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip
should be checked before each ride.
In addition, the cable should be lubri-
cated at the intervals specified in the
periodic maintenance chart.
Recommended lubricant:
Engine oil
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-23
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 23

EAU26001
Care
While the open design of a motorcy-
cle reveals the attractiveness of the
technology, it also makes it more vul-
nerable. Rust and corrosion can
develop even if high-quality compo-
nents are used. A rusty exhaust pipe
may go unnoticed on a car, however,
it detracts from the overall appearan-
ce of a motorcycle. Frequent and pro-
per care does not only comply with
the terms of the warranty, but it will
also keep your motorcycle looking
good, extend its life and optimize its
performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and
covers as well as all electrical
couplers and connectors, inclu-
ding the spark plug cap, are
tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such pro-ducts onto seals, gaskets, sproc-
kets, the drive chain and wheel
axles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10770
CAUTION:
Avoid using strong acidic whe-
el cleaners, especially on spo-
ked wheels. If such products
are used on hard-to-remove
dirt, do not leave the cleaner on
the affected area any longer
than instructed. Also, tho-
roughly rinse the area off with
water, immediately dry it, and
then apply a corrosion protec-
tion spray.
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or spon-
ge with mild detergent and
water to clean plastic.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasivecleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
7
MOTORCYCLE CARE AND STORAGE
7-1
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 34

After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas. Stub-
born dirt and insects will come off
more easily if the area is covered with
a wet cloth for a few minutes before
cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
NOTE:
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA10790
CAUTION:
Do not use warm water since it
increases the corrosive action of
the salt.
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning
1. Dry the motorcycle with a cha-
mois or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, inclu-
ding chrome- and nickel-plated,
surfaces.5. Use spray oil as a universal clea-
ner to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry comple-
tely before storing or covering it.
EWA11130
s s
WARNING
Make sure that there is no oil or
wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent. Before riding at hig-
her speeds, test the motorcy-
cle’s braking performance and
cornering behavior.
ECA10800
CAUTION:
Apply spray oil and wax spa-
ringly and make sure to wipe
off any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
7
MOTORCYCLE CARE AND STORAGE
7-2
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 35

Avoid using abrasive polishing
compounds as they will wear
away the paint.
NOTE:
Consult a Yamaha dealer for advice
on what products to use.
EAU37220
Storage
Short-term
Always store your motorcycle in a
cool, dry place and, if necessary, pro-
tect it against dust with a porous
cover.
ECA10810
CAUTION:
Storing the motorcycle in a
poorly ventilated room or cove-
ring it with a tarp, while it is still
wet, will allow water and humi-
dity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Turn the fuel cock lever to “OFF”.
3. Drain the carburetor float cham-
ber by loosening the drain bolt;
this will prevent fuel depositsfrom building up. Pour the drai-
ned fuel into the fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit sparking
during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark plug
cap.
7
MOTORCYCLE CARE AND STORAGE
7-3
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 36

DimensionsOverall length
2202 mm (86.7 in)
Overall width
689 mm (27.1 in)
Overall height
1175 mm (46.3 in)
Seat height
820 mm (32.3 in)
Wheelbase
1341 mm (52.8 in)
Ground clearance
151 mm (5.94 in)
Minimum turning radius
2900 mm (114.2 in)
WeightWith oil and fuel
124 kg (273 lb)
EngineEngine type
Liquid cooled 2-stroke
Cylinder arrangement
Forward-inclined single cylinder
Displacement
49.7 cm
3(3.03 cu*in)
Bore x stroke
40.3 x 39.0 mm (1.58 x 1.53 in)
Compression ratio
11.5:1
Starting system
Electric starter
Lubrication system
Separate lubrication (Yamaha autolube)
Oil type or gradeRecommended engine oil grade
SAE10W30 type SE motor oil
Cooling systemRadiator capacity (including all routes)
0.70 L (0.74 US qt) (0.62 Imp qt)
Coolant reservoir capacity (up to the maxi-
mum level mark)
0.29L (0.31 US qt) ( 0.26 Imp qt)
Air filterAir filter element
Wet element
Recommended fuelRecommended fuel
Unleaded fuel
Fuel tank capacity
13.8 L (3.65 US gal) (3.04 Imp gal)
Fuel reserve amount
2.2 L (0.58 US gal) (0.48 Imp gal)
CarburetorManufacturer
Dell’Orto
Type x quantity
PHBN 16 x 1
Spark plug (s)Manufacturer/model
NGK/BR 9 ES
Spark plug gap
0.6 ~ 0.7 mm (0.023 ~ 0.027 in)
ClutchClutch type
Wet, multiple-disc
TransmissionPrimary reduction system
Helical gear
Primary reduction ratio
71 x 20 (3.55)
Secondary reduction system
Chain drive
Secondary reduction ratio
60 x 11 (5.45)
Transmission type
Constant mesh 6-speed
Operation
Left foot operation
Gear ratio1-
36 x 12 (3.00)
2-
33 x 16 (2.062)
3-
29 x 19 (1.526)
4-
27 x 22 (1.227)
5-
25 x 24 (1.041)
6-
24 x 25 (0.960)
ChassisFrame type
Double cradle
Caster angle
25 º
Trail
90 mm (3.54 in)
8
SPECIFICATIONS
8-1
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 38

LED
Engine trouble warning light
LED
2-stroke oil warning light
LED
FusesMain fuse
10 A
8
SPECIFICATIONS
8-3
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 40

2-stroke engine oil .....................................3-7
AAir filter element .......................................6-12
Anti-theft device housing ...........................3-9
Autolube pump, adjusting........................6-24
BBattery......................................................6-27
Brake and clutch levers, checking and
lubricating ..............................................6-24
Brake and shift pedals, checking and
lubricating ..............................................6-24
Brake fluid level, checking .......................6-19
Brake fluid, changing ...............................6-20
Brake lever .................................................3-5
Brake pedal ................................................3-5
Brake pedal free play, adjusting ..............6-17
CCables, checking and lubricating ............6-23
Carburetor, adjusting ...............................6-12
Care............................................................7-1
Catalytic converter .....................................3-6
Clutch lever ................................................3-4
Clutch lever free play, adjusting...............6-16
Coolant.......................................................6-9
Coolant temperature warning light ............3-2
Cowlings and panels, removing and
installing ...................................................6-5
DDimmer switch ...........................................3-3
Drive chain slack ......................................6-21
Drive chain, cleaning and lubricating.......6-22
EEngine break-in ..........................................5-3
Engine idling speed .................................6-13Engine stop switch ....................................3-3
Engine trouble warning light ......................3-2
Engine, starting a warm .............................5-2
FFront and rear brake pads, checking ......6-18
Front brake lever free play, checking.......6-17
Front fork, checking .................................6-25
Fuel ............................................................3-5
Fuel cock....................................................3-8
Fuel consumption, tips for reducing ..........5-3
Fuel tank breather/overflow hose ..............3-7
Fuel tank cap .............................................3-6
Fuse, replacing.........................................6-28
HHandlebar switches ...................................3-3
Headlight bulb, replacing .........................6-28
Horn switch ................................................3-3
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-10
Indicator and warning lights ......................3-1
KKey identification number ..........................9-1
LLicense plate light bulb, replacing ...........6-29
MMain switch/steering lock ..........................3-1
Model label ................................................9-2
NNeutral indicator light.................................3-1
OOil level warning light .................................3-2
PParking .......................................................5-4
Part locations .............................................2-1
Pass switch ................................................3-3
Periodic maintenance and lubrication
chart .........................................................6-2
Pre-operation check list .............................4-2
RRear brake light switch, adjusting ...........6-18
Rear view mirrors .......................................3-9
SSafety information ......................................1-1
Seat ............................................................3-9
Shift pedal ..................................................3-4
Shift pedal position, adjusting .................6-18
Shifting .......................................................5-2
Sidestand .................................................3-10
Sidestand, checking and lubricating .......6-25
Spark plug, checking .................................6-7
Specifications.............................................8-1
Speedometer unit ......................................3-2
Start switch ................................................3-4
Starter (choke) lever ...................................3-8
Starting a cold engine ................................5-1
Steering, checking ...................................6-26
Storage.......................................................7-3
TTachometer ................................................3-3
Throttle cable free play, adjusting ............6-12
Throttle grip and cable, checking and
lubricating ..............................................6-23
Tires .........................................................6-14
Tool kit ........................................................6-1
Transmission oil .........................................6-8
INDEX
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 43