wheel YAMAHA VERSITY 300 2004 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2004, Model line: VERSITY 300, Model: YAMAHA VERSITY 300 2004Pages: 104, PDF Size: 2.82 MB
Page 39 of 104
4
PRE-OPERATION CHECKS
ITEM CHECKS PAGE
•Make sure that operation is smooth.
Throttle grip•Check cable free play.
6-20, 6-26
•If necessary, have Yamaha dealer adjust cable free play
and lubricate cable and grip housing.
•Check for damage.
Wheels and tires•Check tire condition and tread depth.
6-21 — 6-23
•Check air pressure.
•Correct if necessary.
Brake levers•Make sure that operation is smooth.
3-9, 6-23, 6-26
•Lubricate lever pivoting points if necessary.
Centerstand, sidestand•Make sure that operation is smooth.
6-27
•Lubricate pivots if necessary.
Chassis fasteners•Make sure that all nuts, bolts and screws are properly tightened.
—
•Tighten if necessary.
Instruments, lights•Check operation.
3-1 — 3-8, 6-32 — 6-35
signals and switches•Correct if necessary.
Sidestand switch•Check operation of ignition circuit cut-off system.
3-16
•If system is defective, have Yamaha dealer check vehicule.
4-2
Page 47 of 104
EAU00462
PERIODIC MAINTENANCE AND MINOR REPAIR
Owner’s tool kit ........................................................ 6-1
Periodic maintenance and lubrication chart ............ 6-2
Removing and installing cowlings and panels ........ 6-5
Checking the spark plug ....................................... 6-11
Engine oil .............................................................. 6-13
Final transmission oil ............................................ 6-16
Coolant .................................................................. 6-17
Air filter and the V-belt case air filter elements ...... 6-18
Adjusting the carburetor ........................................ 6-20
Adjusting the throttle cable free play ..................... 6-20
Adjusting the valve clearance ............................... 6-21
Tires ...................................................................... 6-21
Cast wheels .......................................................... 6-23
Adjusting the front and rear brake lever
free play ................................................................ 6-23
Checking the front and rear brake pads ................ 6-24
Checking the brake fluid level ............................... 6-24
Changing the brake fluid ....................................... 6-25Checking and lubricating the cables ..................... 6-26
Checking and lubricating the throttle grip
and cables ............................................................. 6-26
Lubricating the front and rear brake levers ........... 6-26
Checking and lubricating the centerstand
and sidestand ........................................................ 6-27
Checking the front fork .......................................... 6-27
Checking the steering ........................................... 6-28
Checking the wheel bearings ................................ 6-29
Battery ................................................................... 6-29
Replacing the fuses .............................................. 6-30
Replacing a headlight bulb .................................... 6-32
Replacing a front turn signal light bulb .................. 6-34
Replacing tail/brake light bulb
or rear turn signal light bulb .................................. 6-34
Replacing the license plate light bulb .................... 6-35
Troubleshooting ..................................................... 6-35
Troubleshooting charts .......................................... 6-36
6
Page 50 of 104
PERIODIC MAINTENANCE AND MINOR REPAIR
6
•Check operation, fluid level and vehicle for fluid leakage.
√√√√√ √7 * Rear brake(See NOTE on page 6-4.)
•Replace brake pads. Whenever worn to the limit
8 * Brake hoses•Check for cracks or damage.√√√√ √•Replace. (See NOTE on page 6-4.) Every 4 years
9 * Wheels•Check runout and for damage.√√√√
•Check tread depth and for damage.
10 * Tires•Replace if necessary.
√√√√ √
•Check air pressure.
•Correct if necessary.
11 * Wheel bearings•Check bearing for looseness or damage.√√√√
12 * Steering bearings•Check bearing play and steering for roughness.√√√√√•Lubricate with lithium-soap-based grease. Every 20,000 km
13 * Chassis fasteners•Make sure that all nuts, bolts and screws are
√√√√ √
properly tightened.
14 Sidestand, Centerstand•Check operation.
√√√√ √
•Lubricate.
15 * Sidestand switch•Check operation.√√√√√ √
16 * Front fork•Check operation and for oil leakage.√√√√
17 * Shock absorber assemblies•Check operation and shock absorbers for oil leakage.√√√√
18 * Carburetor•Adjust engine idling speed.√√√√√ √
ODOMETER READING (x 1,000 km)
NO. ITEMCHECK OR MAINTENANCE JOB
1
ANNUAL
CHECK
10 20 30 40
6-3
Page 63 of 104
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU04228
Final transmission oil
The final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Start the engine, warm it up by
riding the scooter for several mi-
nutes, and then stop the engine.
2. Place the scooter on the
centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.4. Remove the oil filler cap and drain
bolt to drain the oil from the final
transmission case.
5. Install the final transmission oil
drain bolt, and then tighten it to
the specified torque.
Tightening torque:
Final transmission oil drain bolt:
22 Nm (2.2 m
•kgf)
6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten the
oil filler cap.
1. Final transmission oil filler cap1. Final transmission oil drain bolt
Recommended final transmission
oil:
See page 8-2.
Oil quantity:
0.25 L
EWA00062
•Make sure that no foreign
material enters the final trans-
mission case.
•Make sure that no oil gets on
the tire or wheel.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
WARNING
6-16
1
ZAUM0441
11
ZAUM0442
Page 69 of 104
PERIODIC MAINTENANCE AND MINOR REPAIR
6 Tire inspection
The tires must be checked before each
ride. If the center tread depth reaches
the specified limit, if the tire has a nail
or glass fragments in it, or if the sidewall
is cracked, have a Yamaha dealer re-
place the tire immediately.
EW000077
Because loading has an enormous
impact on the handling, braking, per-
formance and safety characteristics of
your scooter, you should keep the
following precautions in mind.
•NEVER OVERLOAD THE SCOO-
TER! Operation of an overloaded
scooter may result in tire damage,
loss of control, or severe injury.
Make sure that the total weight of
rider, cargo, and accessories
does not exceed the specified
maximum load for the vehicle.
•Do not carry along loosely
packed items, which can shift
during a ride.
•Securely pack the heaviest items
close to the center of the scooter
and distribute the weight evenly
on both sides.
•Adjust the suspension and tire air
pressure with regard to the load.
•Check the tire condition and air
pressure before each ride.
WARNING
1. Tire tread depth
2. Sidewall
Tire information
This scooter is equipped with tubeless
tires.
Front
Manufacturer Size Type
MICHELIN 120/80-14 58P PILOT CITY TL
Rear
Manufacturer Size Type
MICHELIN 150/70-14 66P PILOT CITY TL
Minimum tire tread depth
(front and rear)1.6 mm
NOTE :
The tire tread depth limits may differ
from country to country. Always comply
with the local regulations.
EAU00683
EW000079
•Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the
scooter with excessively worn
tires decreases riding stability
and can lead to loss of control.
•The replacement of all wheel
and brake related parts,
including the tires, should be
left to a Yamaha dealer, who has
the necessary professional
knowledge and experience.
WARNING
6-22
1
2
ZAUM0054
Page 70 of 104
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU03773
Cast wheels
To maximize the performance,
durability, and safe operation of your
scooter, note the following points
regarding the specified wheels.
•The wheel rims should be
checked for cracks, bends or
warpage before each ride. If any
damage is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair
to the wheel. A deformed or
cracked wheel must be replaced.
•The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse
handling characteristics, and a
shortened tire life.
•Ride at moderate speeds after
changing a tire since the tire sur-
face must first be "broken in" for it
to develop its optimal
characteristics.
EAUM0056
Adjusting the front and rear
brake lever free play
The front and rear brake lever free play
should measure 2 — 5 mm as shown.
Periodically check the front and rear
brake lever free play and, if necessary,
have a Yamaha dealer adjust it.
EW000100
An incorrect brake lever free play
indicates a hazardous condition in
the brake system. Do not operate the
scooter until the brake system has
been checked or repaired by a
Yamaha dealer.
WARNING
a. Front brake free playa. Rear brake free play
6-23
a
ZAUM0107
a
ZAUM0108
Page 75 of 104
PERIODIC MAINTENANCE AND MINOR REPAIR
6 To check the operation
1. Place the scooter on a level sur-
face and hold it in an upright po-
sition.
2. While applying the front brake,
push down hard on the
handlebars several times to check
if the front fork compresses and
rebounds smoothly.
EC000098
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or
repair it.
CAUTION:
EAU00794
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place a stand under the engine
to raise the front wheel off the
ground.
EW000115
Securely support the scooter so that
there is no danger of it falling over.
WARNING
2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the
steering.
6-28
ZAUM0456ZAUM0457
Page 76 of 104
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU01144
Checking the wheel bearings
The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and
lubrication chart. If there is play in the
wheel hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.
EAU04464
Battery
The battery is located behind panel B.
(See page 6-9 for panel removal and
installation procedures.)
This scooter is equipped with a sealed-
type (MF) battery, which does not
require any maintenance. There is no
need to check the electrolyte or to add
distilled water.
1. Battery
To charge the battery
Have a Yamaha dealer charge the
battery as soon as possible if it seems
to have discharged. Keep in mind that
the battery tends to discharge more
quickly if the scooter is equipped with
optional electrical accessories.
EW000116
•Electrolyte is poisonous and
dangerous since it contains
sulfuric acid, which causes
severe burns. Avoid any contact
with skin, eyes or clothing and
always shield your eyes when
working near batteries. In case
of contact, administer the
following FIRST AID.
•EXTERNAL: Flush with
plenty of water.
•INTERNAL: Drink large
quantities of water or milk
and immediately call a
physician.
WARNING
6-29
1
ZAUM0458
Page 86 of 104
SCOOTER CARE AND STORAGE
7
Care
While the open design of a scooter
reveals the attractiveness of the
technology, it also makes it more
vulnerable. Rust and corrosion can
develop even if high-quality
components are used. A rusty exhaust
pipe may go unnoticed on a car,
however, it detracts from the overall
appearance of a scooter. Frequent and
proper care does not only comply with
the terms of the warranty, but it will also
keep your scooter looking good, extend
its life and optimize its performance.Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly
installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.CleaningECA00011
•Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the
affected area any longer than
instructed. Also, thoroughly
rinse the area off with water,
immediately dry it, and then
apply a corrosion protection
spray.
•Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent and
water to clean plastic.
CAUTION:
7-1
Page 87 of 104
SCOOTER CARE AND STORAGE
7
•Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
•Do not use high-pressure
washers or steam-jet cleaners
since they cause water
seepage and deterioration in
the following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric
components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
•For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the
windshield. Test the product on
a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing
compound after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea
or on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads.
NOTE :
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA00012
Do not use warm water since it
increases the corrosive action of the
salt.
2. Apply a corrosion protection spray
on all metal, including chrome-
and nickel-plated, surfaces to
prevent corrosion.
CAUTION:
7-2