oil YAMAHA VX110 2005 Repair Manual

5-37
EPOWRGENERATOR AND STARTER MOTOR
EXPLODED DIAGRAM
Step Procedure/Part name Q’ty Service points
5 Holder 1
6Bolt 3
7 Lighting coil 1
Reverse the disassembly steps for
assembly.
1
7
6
3
2
45
LT
242
LT
242
LT
242LT
242
14 N 
m (1.4 kgf  m, 10 ft  Ib)
6 × 14 mm
4.9 N 
m (0.49 kgf  m, 3.5 ft  Ib)
5 × 14 mm
14 N 
m (1.4 kgf  m, 10 ft  Ib)
6 × 35 mm
4.9 N 
m (0.49 kgf  m, 3.5 ft  Ib)
5 × 10 mm
ProCarManuals.com

5-40
EPOWRGENERATOR AND STARTER MOTOR
Flywheel magneto installation
1. Install:
Woodruff key
Flywheel magneto
Washer
Flywheel magneto bolt
NOTE:
Clean the tapered portion of the crankshaft
and the flywheel magneto hub.
When installing the flywheel magneto, make
sure the woodruff key is properly seated in
the keyway of the crankshaft.
Lubricate the flywheel magneto bolt and
washer with engine oil.
2. Tighten:
Flywheel magneto bolt 1

NOTE:
While holding the flywheel magneto 2
with the
sheave holder 3
, tighten the flywheel mag-
neto bolt.
CAUTION:
Do not reuse the flywheel magneto bolt and
washer, always replace them with new
ones.
T R..
Flywheel magneto bolt:
75 N  m (7.5 kgf  m, 54 ft  lb)
Sheave holder:
YS-01880-A/90890-01701
ProCarManuals.com

5-41
EPOWRCAMSHAFTS
CAMSHAFTS
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step Procedure/Part name Q’ty Service points
CYLINDER HEAD COVER
REMOVALFollow the left “Step” for removal.
1Bolt 4
2 Ignition coil 4
3 Spark plug 4
4 Clamp/breather hose 1/1È
To oil tank
Paint mark a

5Bolt 1
6 Cam position sensor 1
7 Clamp/cooling water hose 1/1É
To transom plate
8 Rubber seal 1
E
4
65
7 8
10
11
12
13 9
LT
572
LT
14
16
15
3
13 N 
m (1.3 kgf  m, 9.4 ft  Ib)
10 N 
m (1.0 kgf  m, 7.2 ft  Ib)
6 × 16 mm 6 × 16 mm
2nd 7.6 N  m (0.76 kgf
 m, 5.5 ft
 Ib) 1st 3.7 N  m (0.37 kgf
 m, 2.7 ft
 Ib)
12 N 
m (1.2 kgf  m, 8.7 ft  Ib)
6 × 22 mm
aÈ
É
1
2
7.6 N 
m (0.76 kgf  m, 5.5 ft  Ib)
6 × 16 mm
LT
572
LTAA
1280B
1280B
ProCarManuals.com

5-54
EPOWRCYLINDER HEAD
CYLINDER HEAD
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step Procedure/Part name Q’ty Service points
CYLINDER HEAD REMOVAL
Follow the left “Step” for removal.
Engine unit Refer to “ENGINE UNIT”.
Intake assembly Refer to “FUEL INJECTION SYSTEM” in
Chapter 4.
Exhaust pipes 1 and 2 Refer to “EXHAUST PIPES 1 AND 2”.
Oil tank Refer to “OIL TANK”.
Intake and exhaust camshaft Refer to “CAMSHAFTS”.
1Bolt 2
2 Hunger 1
3Bolt 3
EEE
E
2 4
1
855
7
9 3 6
6
LT
271
2nd 121 ± 5˚ 1st 20 N • m (2.0 kgf
• m, 14 ft
• Ib)
2nd 140 ± 5˚ 1st 20 N • m (2.0 kgf
• m, 14 ft
• Ib)
10 N •
m (1.0 kgf • m, 7.2 ft • Ib)
6 × 12 mm
10 N •
m (1.0 kgf • m, 7.2 ft • Ib)
6 × 55 mm
8 × 20 mm
6
2nd 105 ± 5˚ 1st 20 N • m (2.0 kgf
• m, 14 ft
• Ib)
2nd 105 ± 5˚ 1st 20 N • m (2.0 kgf
• m, 14 ft
• Ib)
2nd 105 ± 5˚ 1st 20 N • m (2.0 kgf
• m, 14 ft
• Ib)
2nd 105 ± 5˚ 1st 20 N • m (2.0 kgf
• m, 14 ft
• Ib)
E6
4
66
6
ProCarManuals.com

5-57
EPOWRCYLINDER HEAD
3. Measure:
Cylinder head warpage
Out of specification →
Replace the cyl-
inder head.
Cylinder head warpage limit:
0.1 mm (0.004 in)
Measurement steps:
Place a straightedge 1
and a thickness
gauge 2
across the cylinder head.
Measure the warpage.
If the limit is exceeded, replace the cylin-
der head.
Cylinder head installation
1. Install:
Cylinder head
NOTE:
Pass the timing chain through the timing
chain cavity.
Lubricate the cylinder head nuts with engine
oil.
Tighten the cylinder head nuts in the
sequence shown.
T R..
Cylinder head nut
1:
1st:
20 N  m (2.0 kgf  m, 14 ft  lb)
2nd:
121
± 5°
Cylinder head nut
2:
1st:
20 N  m (2.0 kgf  m, 14 ft  lb)
2nd:
105
± 5°
Cylinder head nut
3:
1st:
20 N  m (2.0 kgf  m, 14 ft  lb)
2nd:
140
± 5°
ProCarManuals.com

5-58
EPOWRCYLINDER HEAD
2. Tighten:
Cylinder head bolts 1

NOTE:
Lubricate the cylinder head bolts with engine
oil.
T R..
Cylinder head bolt:
10 N  m (1.0 kgf  m, 7.2 ft  lb)
ProCarManuals.com

5-65
EPOWRVALVES AND VALVE SPRINGS
2. Install the new valve guide 2
by striking
the special service tool from the camshaft
side until the valve guide clip 3
contacts
the cylinder head.
NOTE:
Apply engine oil to the surface of the new
valve guide.
Valve guide remover:
Intake (ø4.0 mm):
YM-04111/90890-04111
Exhaust (ø4.5 mm):
YM-04116/90890-04116
Valve guide installer:
Intake (ø4.0 mm):
YM-04112/90890-04112
Exhaust (ø4.5 mm):
YM-04117/90890-04117
3
E
2
3. Insert the special service tool into the
valve guide 2
, and then ream the valve
guide.
NOTE:
Turn the valve guide reamer clockwise to
ream the valve guide.
Do not turn the reamer counterclockwise
when removing the reamer.
4. Measure:
Valve guide inside diameter
Valve guide reamer:
Intake (ø4.0 mm):
YM-04113/90890-04113
Exhaust (ø4.5 mm):
YM-04118/90890-04118
Valve guide inside diameter:
Intake:
4.000–4.012 mm
(0.1575–0.1580 in)
Exhaust:
4.500–4.512 mm
(0.1772–0.1776 in)
2
ProCarManuals.com

5-70
EPOWRVALVES AND VALVE SPRINGS
2. Compress the valve spring, and then
install the valve cotter 1
using a thin
screwdriver with a small amount of grease
applied to it.
Valve spring compressor:
YM-01253/90890-04019
Valve spring compressor
attachment:
(for the intake valve):
YM-04114/90890-04114
(for the exhaust valve):
YM-04108/90890-04108
3. Lightly tap the valve spring retainer with a
plastic hammer to set the valve cotter
securely.
NOTE:
Apply engine oil to the valve pads and valve
lifters before installation.
ProCarManuals.com

5-71
EPOWRCRANKCASE
CRANKCASE
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step Procedure/Part name Q’ty Service points
OIL PAN AND CRANKCASE
REMOVALFollow the left “Step” for removal.
Engine unit Refer to “ENGINE UNIT”.
Intake assembly Refer to “FUEL INJECTION SYSTEM” in
Chapter 4.
Exhaust pipes 1 and 2 Refer to “EXHAUST PIPES 1 AND 2”.
Exhaust manifold Refer to “EXHAUST MANIFOLD”.
Generator cover Refer to “GENERATOR AND STARTER
MOTOR”.
Oil tank Refer to “OIL TANK”.
Oil pump Refer to “OIL PUMP”.
*: Loosen completely
6
21 20
20 11
10 9
87
23
4
5
16
151718
13 14
1219
1
LT
271
LT
LT
572
LT
LT
572
LT
LT
572
LT
LT
572
LT
LT
572
LT
E
E
AA
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 70 mm
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 20 mm
20 N •
m (2.0 kgf • m, 14 ft • Ib)
8 × 40 mm
2nd *
3rd 15 N • m (1.5 kgf
• m, 11 ft
• Ib) 1st 7.8 N • m (0.78 kgf
• m, 5.6 ft
• Ib)
9 × 105 mm
4th 49 ± 5˚
8.4 N •
m (0.84 kgf • m, 6.1 ft • Ib)
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 55 mm
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 55 mm
7.6 N •
m (0.76 kgf • m, 5.5 ft • Ib)
6 × 16 mm
15 N •
m (1.5 kgf • m, 11 ft • Ib)
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 20 mm
18
AA
1280B
ProCarManuals.com

5-72
EPOWRCRANKCASE
EXPLODED DIAGRAM
Step Procedure/Part name Q’ty Service points
Reduction drive gear case Refer to “REDUCTION DRIVE GEAR”.
Cylinder head Refer to “CAMSHAFTS”.
1 Timing chain 1
2 Engine temperature sensor 1
3 Washer 1
4Bolt 2
5 Thermoswitch (engine) 1
6 Oil pressure switch 1
7Bolt 1
8Bolt 1
9 Anode cover 1
10 Grommet 1
6
21 20
20 11
10 9
87
23
4
5
16
151718
13 14
1219
1
LT
271
LT
LT
572
LT
LT
572
LT
LT
572
LT
LT
572
LT
LT
572
LT
E
E
AA
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 70 mm
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 20 mm
20 N •
m (2.0 kgf • m, 14 ft • Ib)
8 × 40 mm
2nd *
3rd 15 N • m (1.5 kgf
• m, 11 ft
• Ib) 1st 7.8 N • m (0.78 kgf
• m, 5.6 ft
• Ib)
9 × 105 mm
4th 49 ± 5˚
8.4 N •
m (0.84 kgf • m, 6.1 ft • Ib)
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 55 mm
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 55 mm
7.6 N •
m (0.76 kgf • m, 5.5 ft • Ib)
6 × 16 mm
15 N •
m (1.5 kgf • m, 11 ft • Ib)
12 N •
m (1.2 kgf • m, 8.7 ft • Ib)
6 × 20 mm
18
AA
1280B
ProCarManuals.com