fuel reserve YAMAHA XENTER 125 2012 Owners Manual

1
2
3
4
5
6
7
8
9
3-3
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
to the coolant temperature in the
radiator.
● If the engine overheats, see page
6-34 for further instructions.
EAUT1934
Engine trouble warning light “
”
This warning light fl ashes or stays on
if an electrical circuit monitoring the
engine is not working correctly. If this
occurs, have a Yamaha dealer check
the self-diagnosis system.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”. The warning light should
come on for a few seconds, and then
go off.
If the warning light does not come
on initially when the key is turned to
“ON”, or if the warning light remains
on, have a Yamaha dealer check the
electrical circuit.
EAUT3721
Multi-function display
SELECT
RESET
ODOOIL
TRI P 1 BE
L
T TRIP 2
OIL CHANGECLOOK
OUT TEM
P
12
34
56
789
1012 111. V-belt replacement indicator “V-BELT”
2. Clock
3. Oil change indicator “OIL CHANGE”
4. “SELECT” button
5. Fuel level warning indicator “
”
6. Fuel meter
7. Speedometer
8. Odometer
9. “RESET” button
10. Tripmeter 1
11. Ambient temperature display
12. Tripmeter 2
EWA14431
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display. Changing
settings while riding can distract
the operator and increase the risk
of an accident.
The multi-function display is equipped
with the following:● an odometer● a fuel reserve tripmeter (which
shows the distance traveled since
the bottom segment of the fuel
meter and fuel level warning indi-
cator started fl ashing)● two tripmeters (which show the
distance traveled since they were
last set to zero)● an oil change tripmeter (which
shows the distance traveled since
the last engine oil change)● an oil change indicator (which dis-
plays when the engine oil should
be changed)● a V-belt replacement tripmeter
(which shows the distance trav-
eled since the V-belt was last re-
placed)● a V-belt replacement indicator● an ambient temperature display● a clock● a fuel meter
53B-F8199-E0_CS.indd 3-353B-F8199-E0_CS.indd 3-3
2011/11/01 12:32:082011/11/01 12:32:08
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
3-4
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS● a brightness control mode
TIP● When the key is turned to “ON”,
all segments and indicators of the
display come on for a few sec-
onds. During this time, the multi-
function display is performing a
self-test.● Be sure to turn the key to “ON”
before using the “SELECT” and
“RESET” buttons except when
setting the brightness mode.
Odometer, fuel tripmeter, tripme-
ters, oil change tripmeter and V-belt
tripmeter modes
Pushing the “SELECT” button switch-
es the display among the odometer
mode “ODO”, the fuel tripmeter mode
“F”, the tripmeter modes “TRIP 1”
and “TRIP 2”, the oil change tripme-
ter mode “OIL TRIP” and the V-belt
change mode “BELT TRIP” in the fol-
lowing order:
ODO → F → TRIP 1 → TRIP 2 → OIL
TRIP → BELT TRIP → ODO
When approximately 1.6 L (0.42 US
gal, 0.35 Imp.gal) of fuel remains in
the fuel tank, the bottom segment of
the fuel meter and fuel level warn-
ing indicator will start flashing, and
the display will automatically change
to the fuel reserve tripmeter mode
“ F” and start counting the distance
traveled from that point. In that case,
pushing the “RESET” button switches
the display to the previous mode.
To reset a tripmeter, select it by push-
ing the “SELECT” button until “Trip” or
“Trip F” begins fl ashing (“Trip” or “Trip
F” will only flash for five seconds).
While “Trip” or “Trip F” is flashing,
push the “RESET” button for at least
one second. If you do not reset the
fuel reserve tripmeter manually, it will
reset itself automatically and the dis-
play will return to the prior mode after
refueling and traveling 5 km (3 mi).TIPThe display cannot be changed back
to fuel reserve tripmeter “ F” after
pushing the “RESET” button.
OdometerTIP● For the U.K.: For any mode, the
odometer units can be switched
from kilometers to miles by push-
ing the “SELECT” button for 1
second.● If the odometer indicates “-----”,
have a Yamaha dealer check the
multi-function display, as it may
be faulty.
Tripmeters
To reset a tripmeter, select it by push-
ing the “SELECT” button until “TRIP
1” or “TRIP 2” is displayed, and then
push the “RESET” button for at least 1
second.
TIPIf the tripmeter indicates “-----”, have
a Yamaha dealer check the multi-
function display, as it may be faulty.
53B-F8199-E0_CS.indd 3-453B-F8199-E0_CS.indd 3-4
2011/11/01 12:32:082011/11/01 12:32:08
Process BlackProcess Black