brake YAMAHA XMAX 250 2006 User Guide

EAU16760
Starting off
NOTE:
Before starting off, allow the engine to
warm up.
1. Grab bar
1. While pulling the rear brake lever
with your left hand and holding
the grab bar with your right hand,
push the scooter off the centers-
tand.
2. Sit astride the seat, and then
adjust the rear view mirrors.
3. Switch the turn signal on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip
(on the right) in order to take off.
5. Switch the turn signal off.
EAU16780
Acceleration and
deceleration
The speed can be adjusted by ope-
ning and closing the throttle. To incre-
ase the speed, turn the throttle grip in
direction (a). To reduce the speed,
turn the throttle grip in direction (b).
EAU16791
Braking
1. Close the throttle completely.
2. Apply both front and rear brakes
simultaneously while gradually
increasing the pressure.
EWA10300
s s
WARNING
Avoid braking hard or suddenly
(especially when leaning over
to one side), otherwise the sco-
oter may skid or overturn.
Railroad crossings, streetcar
rails, iron plates on road cons-
truction sites, and manhole
covers become extremely slip-
pery when wet. Therefore, slow
down when approaching such
(b)
(a)
ZAUM0199
1
5
OPERATION AND IMPORTANT RIDING POINTS
5-2
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 37

6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-3
EAU17705
Periodic maintenance and lubrication chart
NOTE:
The annual checks must be performed every year, except if a kilometer-based maintenance is performed
instead.
From 50000 km, repeat the maintenance intervals starting from 10000 km.
Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and
technical skills.
ODOMETER READING (x 1000 Km) ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
110203040
1*Fuel line•Check fuel hoses for cracks or damage.√√√√ √
•Check condition.
2Spark plug•Clean and regap.√√
•Replace.√√
3*Valves•Check valve clearance.
•Adjust.√√
4Air filter element•Replace.√√
5*V-belt case air filter •Clean.√√elements•Replace.√√
6*Front brake•Check operation, fluid level and vehicle for fluid leakage.√√ √ √√ √•Replace brake pads. Whenever worn to the limit
7*Rear brake•Check operation, fluid level and vehicle for fluid leakage.√√ √ √√ √
•Replace brake pads. Whenever worn to the limit
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 42

6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
ODOMETER READING (x 1000 Km) ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
110203040
8*Brake hose•Check for cracks or damage.√√√√ √•Replace. Every 4 years
9*Wheels•Check runout and for damage.√√√√
•Check tread depth and for damage.
10 * Tires•Replace if necessary.
•Check air pressure.
•Correct if necessary.√√√√ √
11 *Wheel bearings•Check bearing for looseness or damage.√√√√
12 *Steering bearings•Check bearing play and steering for roughness.√√ √ √√•Lubricate with lithium-soap-based grease. Every 20000 km
13 *Chassis fasteners•Make sure that all nuts, bolts and screws are properly
tightened.√√√√ √
14Sidestand, centerstand•Check operation.
•Lubricate.√√√√ √
15 *Sidestand switch•Check operation.√√ √ √√ √
16 *Front fork•Check operation and for oil leakage.√√√√
17 *Shock absorber
assemblies•Check operation and shock absorbers for oil leakage.√√√√
18 *Carburetor•Adjust engine idling speed.√√ √ √√ √
•Change. (See page 6-8.)√When the oil change indicator light comes
19Engine oilon (every 3000 km)
•Check oil level and vehicle for oil leakage. Every 3000 km√
20 *Cooling system•Check coolant level and vehicle for coolant leakage.√√√√ √
•Change. Every 3 years
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 43

6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
ODOMETER READING (x 1000 Km) ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
110203040
21Final transmission oil•Check vehicle for oil leakage.√√ √•Change.√√√
22 *V-belt•Replace. Every 20000 km
23 *Front and rear brake
switches•Check operation.√√ √ √√ √
24Moving parts and cables•Lubricate.√√√√ √
Throttle grip housing •Check operation and free play.
25 * •Adjust the throttle cable free play if necessary.
and cable
•Lubricate the throttle grip housing and cable.√√√√ √
26 *Mufflers and exhaust
pipes•Check the screw clamps for looseness.√√ √ √√ √
27 *Lights, signals •Check operation.
and switches•Adjust headlight beam.√√ √ √√ √
EAU18660
NOTE:
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinder and caliper, and change the bra-
ke fluid.
• Replace the brake hoses every four years and if cracked or damaged.
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 44

Tire information
This motorcycle is equipped with
tubeless tires.
EWA10470
s s
WARNING
Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the
vehicle with excessively worn
tires decreases riding stability
and can lead to loss of control.
The replacement of all wheel
and brake related parts, inclu-
ding the tires, should be left to
a Yamaha dealer, who has the
necessary professional know-
ledge and experience.
EAU21960
Cast wheels
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified wheels.
The wheel rims should be chec-
ked for cracks, bends or warpage
before each ride. If any damage
is found, have a Yamaha dealer
replace the wheel. Do not
attempt even the smallest repair
to the wheel. A deformed or crac-
ked wheel must be replaced.
The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced.
An unbalanced wheel can result
in poor performance, adverse
handling characteristics, and a
shortened tire life.
Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for
it to develop its optimal characte-
ristics.
EAU33453
Front and rear brake lever
free play
Front
Rear
Front tire:
Size:
120/70 - 15 56S
Manufacturer/model:
Michelin / GoldStandard
Rear tire:
Size:
140/70 - 14 68S
Manufacturer/model:
Michelin / GoldStandard
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 56

There should be no free play at the
brake lever ends. If there is free play,
have a Yamaha dealer inspect the
brake system.
EWA14211
s s
WARNING
A soft or spongy feeling in the bra-
ke lever can indicate the presence
of air in the hydraulic system. If the-
re is air in the hydraulic system,
have a Yamaha dealer bleed the
system before operating the vehi-
cle. Air in the hydraulic system will
diminish the braking performance,
which may result in loss of control
and an accident.
EAU22390
Checking the front and rear
brake pads
The front and rear brake pads must
be checked for wear at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU22400
Front brake pads
1. Lining thickeness
Check each front brake pad for
damage and measure the lining thick-
ness. If a brake pad is damaged or if
the lining thickness is less than 0.5
mm (0.02 in), have a Yamaha dealer
replace the brake pads as a set.
EAU22510
Rear brake pads
1. Brake pad wear indicator groove
The rear brake is provided with a
check plug, which, if it is removed,
allows you to check the brake pad
wear without disassembling the bra-
ke. If the lining thickness is less than
0.5 mm (0.02 in), have a Yamaha dea-
ler replace the brake pads as a set.
11
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 57

EAU22580
Checking the brake fluid
level
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.
Before riding, check that the brake
fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
Observe these precautions:
When checking the fluid level,
make sure that the top of the bra-
ke fluid reservoir is level.
Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performan-
ce.
Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-
cantly lower the boiling point of
the fluid and may result in vapor
lock.
Brake fluid may deteriorate pain-
ted surfaces or plastic parts.
Always clean up spilled fluid
immediately.
As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if
the brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.
Recommended brake fluid:
DOT 4
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-19
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 58

EAU22720
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addi-
tion, have the oil seals of the brake
master cylinder and caliper as well as
the brake hose replaced at the inter-
vals listed below or whenever they are
damaged or leaking.
Oil seals: Replace every two
years.
Brake hose: Replace every four
years.
EAU23111
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip
should be checked before each ride.
In addition, the cable should be lubri-
cated at the intervals specified in the
periodic maintenance chart.
EAU23170
Lubricating the front and
rear brake levers
The pivoting points of the front and
rear brake levers must be lubricated
at the intervals specified in the perio-
dic maintenance and lubrication
chart.
Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 59

2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and
rebounds smoothly.
ECA10590
CAUTION:
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or
repair it.
EAU23280
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Place a stand under the engine to
raise the front wheel off the
ground.
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling over.
2. Hold the lower ends of the front
fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
EAU23290
Checking the wheel bearings
The front and rear wheel bearings
must be checked at the intervals spe-
cified in the periodic maintenance and
lubrication chart. If there is play in the
wheel hub or if the wheel does not
turn smoothly, have a Yamaha dealer
check the wheel bearings.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-22
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 61

EAUS1250
Replacing the tail/brake light
bulb or a rear turn signal
light bulb
Tail/brake light bulb
1. Remove the tail/brake light bulb
lens by removing the screws.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.Rear turn signal light bulb
1. Remove the tail/brake light lens
by removing the screw.
2. Remove the turn signal light bulb
lens by removing the screw.
3. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the turn signal light bulb
lens by installing the screw.
6. Install the tail/brake light bulb
lens by installing the screw.
ECA10680
CAUTION:
Do not overtighten the screws,
otherwise the lens may break.
EAUS1150
Replacing the license plate
light bulb
1. Remove the lens by removing the
screw.
2. Remove the defective bulb by
pulling it out.
3. Insert a new bulb into the socket.
4. Install the lens by installing the
screw.
ECA11190
CAUTION:
Do not overtighten the screw,
otherwise the lens may break.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-27
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 66