fuel YAMAHA XMAX 250 2010 User Guide

EAU46861
TIP
The annual checks must be performed every year, except if a kilometer-based maintenance, or for the UK,
a mileage-based maintenance, is performed instead.
From 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (6000 mi).
Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and
technical skills.
EAU46910
Periodic maintenance chart for the emission control system
PERIODIC MAINTENANCE AND ADJUSTMENT
6-3
6
ODOMETER READING
CHECK OR ANNUAL
NO. ITEM MAINTENANCE JOB 1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
1* Fuel line • Check fuel hoses for cracks or
damage. √√√ √√
• Check condition.
2 Spark plug • Clean and regap. √√
• Replace.
√√
3* Valves • Check valve clearance.
• Adjust. √√
4*
Fuel injection • Check engine idle speed. √√ √ √ √ √
5* Muffler and exhaust
• Check the screw clamp(s)
√√ √ √ √
pipe for looseness.

37P-F8199-E0 18/9/09 14:54 Página 44

EAU21382
Checking the throttle cable
free play
1. Throttle cable free play
The throttle cable free play should
measure 3.0–5.0 mm (0.12–0.20 in) at
the throttle grip. Periodically check
the throttle cable free play and, if
necessary, have a Yamaha dealer
adjust it.
EAU21401
Valve clearance
The valve clearance changes with
use, resulting in improper air-fuel mix-
ture and/or engine noise. To prevent
this from occurring, the valve clearan-
ce must be adjusted by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.
EAU21873
Tires
To maximize the performance, durabi-
lity, and safe operation of your vehi-
cle, note the following points regar-
ding the specified tires.
Tire air pressure
The tire air pressure should be chec-
ked and, if necessary, adjusted befo-
re each ride.
EWA10501
Operation of this vehicle with
improper tire pressure may cause
severe injury or death from loss of
control.
The tire air pressure must be
checked and adjusted on cold

WARNING

ZAUM0053

PERIODIC MAINTENANCE AND ADJUSTMENT
6-16
6

37P-F8199-E0 18/9/09 14:54 Página 57

EAU25881
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition sys-
tems, for example, can cause poor
starting and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your scooter
require any repair, take it to a Yamaha
dealer, whose skilled technicians
have the necessary tools, experience,
and know-how to service the scooter
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
EWA15141
When checking the fuel system, do
not smoke, and make sure there
are no open flames or sparks in thearea, including pilot lights from
water heaters or furnaces. Gasoli-
ne or gasoline vapors can ignite or
explode, causing severe injury or
property damage.

WARNING

PERIODIC MAINTENANCE AND ADJUSTMENT
6-29
6

37P-F8199-E0 18/9/09 14:54 Página 70

PERIODIC MAINTENANCE AND ADJUSTMENT
6-30
6
EAU42131
Troubleshooting charts
Starting problems or poor engine performance

Check the fuel level in
the fuel tank.
1. FuelThere is enough fuel.There is no fuel.Check the compression.
Supply fuel.
The engine does not start.
Check the compression.
Operate the electric starter.
2. CompressionThere is compression.
There is no compression.Check the ignition. Have a Yamaha dealer
check the vehicle.
Remove the spark plug
and check the electrodes.
3. IgnitionWipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Have a Yamaha dealer check the vehicle.
The engine does not start.
Have a Yamaha dealer
check the vehicle.
The engine does not start.
Check the battery.
Operate the electric starter. The engine turns over
quickly.
The engine turns over
slowly.
The battery is good.
Check the battery lead connections,
and charge the battery if necessary.
Dry
WetOperate the electric starter.

37P-F8199-E0 18/9/09 14:54 Página 71

with water may be used. Be
sure to rinse off any detergent
residue using plenty of water,
as it is harmful to plastic parts.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leavescratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas. Stub-
born dirt and insects will come off
more easily if the area is covered with
a wet cloth for a few minutes before
cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
TIP
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down. NOTI-
CE: Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]
2. Apply a corrosion protection spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning 1. Dry the scooter with a chamois or an absorbing cloth.
2. Use a chrome polish to shine chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
SCOOTER CARE AND STORAGE
7-2
7

37P-F8199-E0 18/9/09 14:54 Página 74

3. To prevent corrosion, it is recom-mended to apply a corrosion pro-
tection spray on all metal, inclu-
ding chrome- and nickel-plated,
surfaces.
4. Use spray oil as a universal clea- ner to remove any remaining dirt.
5. Touch up minor paint damage caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely before storing or covering it.
EWA10941
Contaminants on the brakes or
tires can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent.
Before operating the scooter
test its braking performance
and cornering behavior.
ECA10800
Apply spray oil and wax spa-
ringly and make sure to wipe
off any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP
Consult a Yamaha dealer for
advice on what products to use.
Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from
the lens.
EAU36561
Storage
Short-term
Always store your scooter in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
ECA10820
Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your scooter for seve-
ral months:1. Follow all the instructions in the “Care” section of this chapter.
2. Fill up the fuel tank and add fuel stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.

NOTICE

NOTICE

WARNING

SCOOTER CARE AND STORAGE
7-3
7

37P-F8199-E0 18/9/09 14:54 Página 75

Dimensions:Overall length:2201 mm (86.7 in)
Overall width: 776 mm (30.6 in)
Overall height: 1337 mm (52.6 in)
Seat height: 792 mm (31.2 in)
Wheelbase: 1545 mm (60.8 in)
Ground clearance: 134 mm (5.30 in)
Minimum turning radius: 1805 mm (71.1 in)
Weight:With oil and fuel:177.4 kg (391 lb)
Engine:Engine type:Liquid cooled 4-stroke, SOHC
Cylinder arrangement: Forward-inclined single cylinder
Displacement: 249 cm
3
Bore x stroke:69.0 x 66.8 mm (2.72 x 2.63 in)
Compression ratio: 10.00 :1
Starting system: Electric starter
Lubrication system: Wet sump
Engine oil:Type:SAE 10W-30, SAE 10W-40, SAE 15W-40,
SAE 20W-40 or SAE 20W-50
Recommended engine oil grade: API service SF, SG type or higher, JASO
standard MA
Engine oil quantity:Periodic oil change: 1.30 L (1.37 US qt, 1.14 Imp.qt)
Final transmission oil:Type:SAE 10W-30 type SE motor oil
Quantity: 0.25 L (0.26 US qt, 0.22 Imp.qt)
Cooling system:Coolant reservoir capacity (up to the maxi-
mum level mark):0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes): 1.00 L (1.06 US qt, 0.88 Imp.qt)
Air filter:Air filter element:Oil-coated paper element
Fuel:Recommended fuel:Regular unleaded gasoline only
Fuel tank capacity: 11.8 L (3.12 US gal, 2.60 Imp.gal)
Fuel reserve amount: 1.7 L (0.45 US gal, 0.37 Imp.gal)
Throttle body:ID mark:1C04 00
Manufacturer: AISAN
Spark plug (s):Manufacturer/model:NGK/DPR8EA-9
Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)
Clutch:Clutch type:Dry, centrifugal automatic
Transmission:Primary reduction system:Helical gear
Primary reduction ratio: 40/15 (2.666)
Secondary reduction system: Helical gear
Secondary reduction ratio: 40/14 (2.857)
Transmission type: V-belt automatic

-20 -10 0 10 20 30
40 50 ˚C
SAE 10W-30
SAE 15W-40
SAE 20W-40
SAE 20W-50
SAE 10W-40
SAE 10W-50

SPECIFICATIONS
8-1
8

37P-F8199-E0 18/9/09 14:54 Página 77

AAcceleration and deceleration ...................5-2
Air filter and V-belt case air filter elements ................................................6-15
Auxiliary light bulb, replacing ...................6-28
BBattery......................................................6-24
Brake fluid level, checking .......................6-20
Brake fluid, changing ...............................6-21
Brake lever, front ......................................3-12
Brake lever, rear .......................................3-12
Brake levers, lubricating ..........................6-21
Braking .......................................................5-3
CCare............................................................7-1
Catalytic converters .................................3-14
Centerstand and sidestand, checking and lubricating .......................................6-22
Coolant.....................................................6-13
Cowling and panel, removing and installing ...................................................6-8
DDimmer switch .........................................3-11
EEngine break-in ..........................................5-4
Engine oil .................................................6-10
Engine trouble warning light ......................3-4
FFinal transmission oil ...............................6-12
Front and rear brake lever free play.........6-18
Front and rear brake pads, checking ......6-19
Front fork, checking .................................6-23
Fuel ..........................................................3-13
Fuel consumption, tips for reducing ..........5-3 Fuel tank cap ...........................................3-12
Fuses, replacing .......................................6-25
HHandlebar switches .................................3-11
Hazard switch ..........................................3-11
Headlight bulb, replacing .........................6-26
High beam indicator light...........................3-4
Horn switch ..............................................3-11
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-19
Immobilizer system ....................................3-1
Immobilizer system indicator light .............3-4
Indicator and warning lights ......................3-4
KKey identification number ..........................9-1
LLicense plate light bulb, replacing ...........6-28
MMain switch/steering lock ..........................3-2
Maintenance and lubrication, periodic ......6-4
Maintenance, emission control system .....6-3
Matte color, caution ...................................7-1
Model label ................................................9-2
Multi-function display ................................3-6
PParking .......................................................5-4
Part locations .............................................1-5
Pass switch ..............................................3-11
SSafe-riding points.......................................1-5
Safety information ......................................1-1
Seat ..........................................................3-15
Securing bracket ......................................3-15Shock absorber assemblies, adjusting....3-18
Sidestand .................................................3-18
Spark plug, checking .................................6-9
Specifications.............................................7-3
Speedometer .............................................3-5
Start switch ..............................................3-11
Starting off .................................................5-2
Starting the engine.....................................5-1
Steering, checking ...................................6-23
Storage.......................................................7-3
Storage compartments ............................3-16
TTachometer ................................................3-5
Tail/brake light bulb or rear turn signal
light bulb, replacing ...............................6-27
Throttle cable free play, checking ............6-16
Throttle grip and cable, checking and lubricating ..............................................6-21
Tires .........................................................6-16
Tool kit ........................................................6-2
Troubleshooting .......................................6-29
Troubleshooting charts ............................6-30
Turn signal indicator lights .........................3-4
Turn signal light bulb (front), replacing ................................................6-27
Turn signal switch ....................................3-11
VValve clearance ........................................6-16
Vehicle identification number .....................9-1
WWheel bearings, checking........................6-24
Wheels .....................................................6-18
INDEX

37P-F8199-E0 18/9/09 14:54 Página 82