key YAMAHA XT660Z 2009 User Guide

INSTRUMENT AND CONTROL FUNCTIONS
3-10
1
2
3
4
5
6
7
8
9
10
EAU12733
Hazard switch “r”
With the key in the “ON” or Fposition,
use this switch to turn on the hazard
lights (simultaneous flashing of all turn
signal lights).
The hazard lights are used in case of
an emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.
ECA10061CAUTION:
Do not use the hazard lights for an
extended length of time with the
engine not running, otherwise the
battery may discharge.
EAU12820
Clutch lever
1. Clutch lever
The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the han-
dlebar grip. To engage the clutch, re-
lease the lever. The lever should be
pulled rapidly and released slowly for
smooth clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-17).

1

EAU12870
Shift pedal
1. Shift pedal
The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.

XT660Z 01-03 ING 10-03-2008 16:11 Pagina 3-10

1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-11
EAU26822
Brake lever
1. Brake lever
2. Position adjusting dial
3. Arrow mark
4. Distance
The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the han-
dlebar grip.
The brake lever is equipped with a po-
sition adjusting dial. To adjust the dis-
tance between the brake lever and the
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure
that the appropriate setting on the ad-
justing dial is aligned with the “˙”
mark on the brake lever.

EAU12941
Brake pedal
1. Brake pedal
The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

1

EAU13072
Fuel tank cap
1. Lock cover
2. Open
To open the fuel tank cap
Open the fuel tank cap lock cover, in-
sert the key into the lock, and then turn
it 1/4 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened.

XT660Z 01-03 ING 10-03-2008 16:11 Pagina 3-11

INSTRUMENT AND CONTROL FUNCTIONS
3-12
1
2
3
4
5
6
7
8
9
10
To close the fuel tank cap 1. Push the fuel tank cap into posi- tion with the key inserted in the
lock.
2. Turn the key counterclockwise to the original position, remove it,
and then close the lock cover.
NOTE:
The fuel tank cap cannot be closed
unless the key is in the lock. In addi-
tion, the key cannot be removed if the
cap is not properly closed and locked.
EWA11090
WARNING0
Make sure that the fuel tank cap is
properly closed before riding.

EAU13211
Fuel
1. Fuel tank filler tube
2. Fuel level
Make sure that there is sufficient fuel
in the tank. Fill the fuel tank to the bot-
tom of the filler tube as shown.
EWA10880
WARNING0
• Do not overfill the fuel tank,otherwise it may overflow when
the fuel warms up and expands.
• Avoid spilling fuel on the hot
engine.

ECA10070CAUTION:
Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since
fuel may deteriorate painted sur-
faces or plastic parts.
EAU13390
Recommended fuel: PREMIUM UNLEADED
GASOLINE ONLY
Fuel tank capacity: 23.0 L (6.07 US gal) (5.05 Imp.gal)
Fuel reserve amount (when the fuel
level warning light comes on): 6.7 L (1.77 US gal) (1.47 Imp.gal)

XT660Z 01-03 ING 10-03-2008 16:11 Pagina 3-12

INSTRUMENT AND CONTROL FUNCTIONS
3-14
1
2
3
4
5
6
7
8
9
10
To install the seat
1. Projections
2. Seat holders
1. Insert the projections on the front of the seat into the seat holders.
2. Push the rear of the seat down.
NOTE:
Make sure that the seat is properly se-
cured before riding.

EAU13870
Seat
To remove the seat
1. Seat lock
2. Unlock
1. Insert the key into the lock, and then turn it counterclockwise.
2. Pull the seat off.

ECA10700CAUTION:
The following precautions must be
observed to prevent a fire hazard or
other damages.
●Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.
●Never park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
●Do not allow the engine to idle
too long.

XT660Z 01-03 ING 10-03-2008 16:11 Pagina 3-14

INSTRUMENT AND CONTROL FUNCTIONS
3-18
1
2
3
4
5
6
7
8
9
10
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.
Does the engine start?
With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.
Does the engine stall?
NOTE:
This check is most reliable if performed with a
warmed-up engine.
The neutral switch may be defective.
The motorcycle should not be ridden until checked by a
Yamaha dealer.
The sidestand switch may be defective.
The motorcycle should not be ridden until checked by a
Yamaha dealer.
The clutch switch may be defective.
The motorcycle should not be ridden until checked by a
Yamaha dealer.
After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.
Does the engine start?
The system is OK. The motorcycle can be ridden.
YES NO
NO
YES
NO
YES

XT660Z 01-03 ING 10-03-2008 16:11 Pagina 3-18

1
2
3
4
5
6
7
8
9
10
OPERATION AND IMPORTANT RIDING POINTS
EAU15950
EWA10270
WARNING0
●Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.
●Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
●Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.

EAUB1570
Starting the engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
●The transmission is in the neutral
position.
●The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
WARNING0
●Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure de-
scribed on page 3-18.
●Never ride with the sidestand
down.
1. Turn the key to “ON” and make sure that the engine stop switch is
set to “
I”.

ECAB0070CAUTION:
The following warning lights and in-
dicator lights should come on for a
few seconds, then go off.
●Neutral indicator light
●Turn signal indicator light
●High beam indicator light
●Engine trouble warning light
●Coolant temperature warning
light
●Immobilizer system indicator
light
If a warning or indicator light does
not go off, see page 3-3 for the cor-
responding warning and indicator
light circuit check.
2. Shift the transmission into the neutral position.
NOTE:
When the transmission is in the neu-
tral position, the neutral indicator light
should be on, otherwise have a Yama-
ha dealer check the electrical circuit.
5-1

XT660Z 04-06 ING 11-03-2008 8:30 Pagina 5-1

OPERATION AND IMPORTANT RIDING POINTS
ECA10310CAUTION:
●Keep the engine speed out of
the tachometer red zone.
●If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the
vehicle.
5-4
1
2
3
4
5
6
7
8
9
10
EAU17212
Parking
When parking, stop the engine, and
then remove the key from the main
switch.
EWA10310
WARNING0
●Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.
●Do not park on a slope or on
soft ground, otherwise the ve-
hicle may overturn.
ECA10380CAUTION:
Never park in an area where there
are fire hazards such as grass or
other flammable materials.

XT660Z 04-06 ING 11-03-2008 8:30 Pagina 5-4

PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
1
2
3
4
5
6
7
8
9
10
ECA10640CAUTION:
Do not use a fuse of a higher am-
perage rating than recommended
to avoid causing extensive damage
to the electrical system and possi-
bly a fire.
3. Turn the key to “ON” and turn on the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
1. Parking lighting fuse
2. Signaling system fuse
3. Headlight fuse
4. Ignition fuse
5. Electronic fuel injection fuse
6. Radiator fan fuse
7. Backup fuse
8. Reserve fuses
The main fuse and fuse box are locat-
ed under the seat. (See page 6-31.)
If a fuse is blown, replace it as follows.1. Turn the key to “OFF” and turn off the electrical circuit in question.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage.

7
8
654321
Specified fuses:
Main fuse:30 A
Parking lighting fuse: 10 A
Signalling system fuse: 10 A
Headlight fuse: 20 A
Ignition fuse: 10 A
Fuel injection system fuse: 10 A
Radiator fan fuse: 7.5 A
Backup fuse (for odometer,
clock and immobilizer): 10 A

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-32

1
2
3
4
5
6
7
8
9
10
CONSUMER INFORMATION
9-1
EAU26351
Identification numbers
Record the key identification number,
vehicle identification number and
model label information in the spaces
provided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the ve-
hicle is stolen.
KEY IDENTIFICATION NUMBER:
VEHICLE IDENTIFICATION NUMBER:
MODEL LABEL INFORMATION:å
ç
EAU26381
Key identification number
1. Key identification number
2. Code re-registering key (red bow)
3. Standard keys (black bow)
The key identification number is
stamped into the key tag.
Record this number in the space pro-
vided and use it for reference when or-
dering a new key.

EAU26400
Vehicle identification number
1. Vehicle identification number
The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.
NOTE:
The vehicle identification number is
used to identify your motorcycle and
may be used to register your motorcy-
cle with the licensing authority in your
area

1

XT660Z 07-10 ING 11-03-2008 8:33 Pagina 1

INDEX
1
2
3
4
5
6
7
8
9
10
Ignition circuit cut-off system............3-17 Checking operation procedure......3-18
Immobilizer system ............................3-1
Immobilizer system indicator light ......3-4
Indicator and warning lights ...............3-3 Coolant temperature warning
light .................................................3-4
Engine trouble warning light ...........3-4
High beam indicator light ................3-4
Immobilizer system indicator light...3-4
Neutral indicator light ......................3-4
Turn signal indicator light ................3-3
Instruments ........................................2-3
Instrument and control functions........3-1
K Key identification number ...................9-1
Keys ...................................................3-1
L License plate light bulb, replacing ....6-35
Lubricating the brake and clutch levers ..................................6-26
Lubricating the brake pedal..............6-27
Lubricating the cables ......................6-25
Lubricating the drive chain ...............6-25
Lubricating the sidestand .................6-27
Lubricating the throttle grip and cable .............................................6-26
Lubricating the swingarm pivots.......6-28
M Main switch/steering lock ...................3-2 Model label .........................................9-2
Multi-function display..........................3-5
Clock mode .....................................3-7
Self-diagnosis devices ....................3-7
Tachometer .....................................3-6
Tripmeter and tachometer modes ...3-6
N Neutral indicator light .........................3-4
O Oil filter element ...............................6-10
Operation and important riding points ..............................................5-1
Owner’s tool kit...................................6-1
P Panels, removing and installing .........6-6
Parking ...............................................5-4
Pass switch ........................................3-9
Periodic maintenance and lubrication chart ..............................6-2
Periodic maintenance and minor repair...............................................6-1
Pre-operation check list......................4-2
Pre-operation checks .........................4-1
R Rear suspension, lubricating............6-27
Rear wheel .......................................6-38 Installing........................................6-39
Removing......................................6-38
Record the identification numbers .....9-1 S
Safety information ..............................1-1
Seat ..................................................3-14
Self-diagnosis devices .......................3-7
Shift pedal ........................................3-10
Shifting ...............................................5-2
Shock absorber assembly (adjusting) .....................................3-16
Sidestand .........................................3-17
Sidestand, checking and lubricating .....................................6-27
Sidestand switch, checking ..............3-18
Spark plug, checking..........................6-8
Specifications .....................................8-1
Spoke wheels ...................................6-19
Start switch ........................................3-9
Starting the engine.............................5-1
Steering, checking............................6-29
Steering lock ......................................3-2
Storage...............................................7-3
Supporting the motorcycle ...............6-36
Swingarm, lubricating the pivots ......6-28
T Tachometer ........................................3-6
Tail/brake light ..................................6-34
Throttle cable free play, checking.....6-16
Throttle grip and cable, checking and lubricating ..............................6-26
Tips for reducing fuel consumption ....5-3
Tires .................................................6-16 Air pressure ..................................6-16

XT660Z 07-10 ING 11-03-2008 8:33 Pagina 2