compression ratio YAMAHA YBR125 2007 Owners Manual

Rear wheel installation1. Install the rear wheel and the
axle.
2. Install the axle nut.
3. Insert the brake rod into the
brake cam lever and install the
brake free play adjusting nut.
4. Install the tension bar onto the
brake shoe plate and tighten the
tension bar nut to the specified
tightening torque.
5. Take the Motorcycle off the
centerstand.
6. Tighten the axle nut to the
specified tightening torque.
Then install a new cotter pin.
Specified torque:
Tension bar nut:
14 ft-lb (1.9 m kg)
Axle nut:
65 ft-lb (9.05 m kg)Always use a new cotter pin.
Check the operation of the brake
light after adjusting the rear brake. 7. Adjust the rear brake pedal free
play. (See page 6-17.)
TroubleshootingAlthough YAMAHA Motorcycles
receive a rigid inspection before
shipment from the factory, trouble
may occur during operation. Any
problem in the fuel, compression, or
ignition systems can cause poor
starting and loss of power. The
troubleshooting chart describes a
quick, easy procedure for making
checks. If your Motorcycle requires
any repair, bring it to a YAMAHA
dealer. The skilled technicians at a
YAMAHA dealership have the tools,
experience, and know-how to
properly service your Motorcycle.
Use only genuine YAMAHA parts
on your Motorcycle. Imitation
parts may look like YAMAHA
parts, but they are often inferior.
Consequently, they have a shorter
service life and can lead to
expensive repair bills.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
WARNINGWARNING

SPECIFICATIONS
8-1
SpecificationsModel LIBERO (5TS8)
Dimensions
Kerb weight :(With Engine Oil &
90% Fuel in Tank)- 119Kg.
Engine ::
Overall length 2,000 mm
Overall width 730 mm
Overall height 1,050 mm
Seat height (Upto Rider) 800 mm
(Upto Pillion Rider) 850 mm
Wheelbase 1,290 mm
Ground clearance 173 mm
Minimum turning radius 2,000 mm
Engine type
Cylinder arrangement
Displacement
Bore x Stroke 49X56
Compression ratio 9 : 1
Starting system
Lubrication system
Maximum power 7.6
Maximum torque 0.80Air cooled 4-stroke,SOHC
Forward inclined single
cylinder
106 cm
mm
Kick starter
Wet sump
PS(5.59 KW) @ 7500
Kgm. @ 6000
3
RPM
RPM
EngineOil:
Capacity
Air filter:
Fuel :
Carburettor:Type:
:
Periodic oil change 1.0
Total amount
Type G
Fuel tank capacity
Reserve amount
Type Variable Venturi Type
Manufacturer M/S Keihin Fie PrivateBe sure to use motor oils that do not contain
antifriction modifiers. Passenger car motor oils (often
labelled Energy conserving) contain anti-friction
additives which will cause clutch and/or starter clutch
slippage, resulting in reduced component life and
poor engine performance.
YAMALUBE 4-Stroke motor
oil (20W40 type SG)
L
1.2 L (First fill/Overhaul)
Wet type element
asoline (Petrol)
13.0 Litres
1.7Litres
Limited India.
CAUTION :

b. Spark Plug :Recommended No. P-RA7HC(Champion)
Gap 0.8 ±0.1 mm
c. Valve Clearance :(Cold condition)
(If required) Inlet0.08 ~ 0.12 mm
Exhaust0.10 ~ 0.14 mm
(After matching of the mark on sprocket cam chain with mark on Cylinder
Head Casting and ensuring the Piston at TDC of compression stroke.)
d. Kick Operation: For free Movement
e. Carburetor : • Idle RPM
In warmed up condition
(1300~1500 RPM)
• Check for Overflow
f. Drive Chain : • Alignment
• Slackness(20 ~ 30 mm)
g. FastenersSpecified Torque
(Ft-Lb)
1. Cylinder Head Bolts14-17
2. Engine Mounting
a) Engine Mounting Front and Stay Front25-29
b) Stay Engine Front and Frame25-29c) Engine Mounting Rear and Frame25-29d) Engine Mounting Upper &
Stay Engine Upper25-29e) Stay Engine Upper and Frame25-29f) Engine Mounting Front Lower and Frame25-29
3. Front and Rear Silencer Mounting Nut9-124. Crown Handle Centre Bolt8-14
PRE-DELIVERY INSPECTION REPORT
10-3
service2.pmd11/3/2006, 8:50 PM 3