check engine YAMAHA YBR250 2007 User Guide

6-10
6
PERIODIC MAINTENANCE AND MINOR REPAIR
2
2
1
1. Oil filter element
2. O-ringMake sure that the O-rings are properly
seated.7. Install the oil filter element coverby installing the bolts, then
tightening them to the specified
torque.Tightening torque:Oil filter element cover bolt: 10 Nm (1,0 m.kgf, 7.4 ft.lbf)8. Install the engine oil drain bolt, and
then tighten it to the specified
torque.
9. Install the oil filter element drain bolt, and then tighten it to the
specified torque.
Tightening torque:Engine oil drain bolt: 20 Nm (2.0 m.kgf, 15 ft.lbf)
Oil filter element drain bolt: 7 Nm (0.7 m.kgf, 5.25 ft.lbf)10. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler bolt.Recommended engine oil:See page 8-1
Oil quantity: Without oil filter element
replacement:1.35 L (1.43 US qt) (1.19
Imp.qt)
With oil filter element replacement:1.45 L (1.53 US qt) (1.28
Imp.qt)
ECA11620
l
l l
l
l
In order to prevent clutch
slippage (since the engine oil
also lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
l
l l
l
l
Make sure that no foreign
material enters the crankcase.
11. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off and
check for the cause.
12. Turn the engine off, and then check the oil level and correct it if
necessary.
cap 6.pmd 24/1/2007, 14:37
10

6-12
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU21311
Checking the engine idling
speedThe engine idling speed must be
checked as follow and, if necessary,
adjusted by a Yamaha dealer at the
intervals specified in the periodic
maintenance and lubrication chart.
Start the engine and warm it up for
several minutes at 1000-2000 r/min while
occasionally revving it to 4000-5000 r/
min.The engine is warm when it quickly
responds to the throttle.Engine idling speed:1.300 - 1.500 r/min.
EAU21382
Checking the throttle cable
free play
1
1. Throttle cable free playThe throttle cable free play should
measure 3.0 - 5.0 mm (0.12 - 0.20 in)
at the throttle grip. Periodically check the
throttle cable free play and, if necessary,
have a Yamaha dealer adjust it.
EAU21401
Valve clearancel
The valve clearance changes with
use, resulting in improper air-fuel
mixture and/or engine noise. To
prevent this from occurring, the
valve clearance must be adjusted
by a Yamaha dealer at the intervals
specified in the periodic
maintenance and lubrication chart.
cap 6.pmd 24/1/2007, 14:37
12

6-19
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU22760
Drive chain slackThe drive chain slack should be checked
before each ride and adjusted if
necessary.
EAU22772
To check the drive chain slack
1
1. Drive chain slack1. Place the motorcycle on thesidestand.When checking and adjusting the drive
chain slack, there should be no weight
on the motorcycle.2. Shift the transmission into theneutral position.
3. Move the rear wheel by pushing the motorcycle to locate the tightest portion of the drive chain,
and then measure the drive chain
slack as shown.
Drive chain slack:
25.0 - 35.0 mm (0.98 - 1.38 in)4. If the drive chain slack is incorrect,
adjust it as follows.
EAU22821
To adjust the drive chain slack1. Axle nut
2. Drive chain slack adjusting nut
3. Locknut
4. Alignment marks1. Loosen the brake pedal free playadjusting nut, axle nut, and locknut
at each end of the swingarm.
2. To tighten the drive chain, turn the adjusting nut at each end of the swingarm in direction (a). To loosen
the drive chain, turn the adjusting
nut at each end of the swingarm in
direction (b), and then push the rear
wheel forward.
Using the alignment marks on each side
of the swingarm, make sure that both
adjusting nuts are in the same position
for proper wheel alignment.
ECA10570
Improper drive chain slack will
overload the engine as well as other
vital parts of the motorcycle and can
lead to chain slippage or breakage.
To prevent this from occurring, keep
the drive chain slack within the
specified limits.3. Tighten both locknuts and the axle
nut to the specified torques.
cap 6.pmd 24/1/2007, 14:38
19

6-20
6
PERIODIC MAINTENANCE AND MINOR REPAIRTightening torques:Locknut:
16 Nm (1.6 m.kgf, 12 ft.lbt)
Axle nut: 104 Nm (10.4 m.kgf, 77 ft.lbt)4. Adjust the brake pedal free play.
(See page 6-16.)
EWA10660
After adjusting the brake pedal free
play, check the operation of the brake
light.
EAU23022
Cleaning and lubricating the
drive chainThe drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrication
chart, otherwise it will quickly wear out,
especially when riding in dusty or wet
areas. Service the drive chain as follows.
ECA10581
The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.1. Clean the drive chain with keroseneand a small soft brush.
ECA11120
To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain
lubricant.
ECA11110
Do not use engine oil or any other
lubricants for the drive chain, as they
may contain substances that could
damage the O-rings.
cap 6.pmd
24/1/2007, 14:38
20

6-21
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23100
Checking and lubricating the
cablesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the
cables and cable ends should be
lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or replace
it.Recommended lubricant:Engine oil
EWA10720
Damage to the outer sheath may
interfere with proper cable operation
and will cause the inner cable to rust.
Replace a damaged cable as soon as
possible to prevent unsafe
conditions.
EAU23111
Checking and lubricating the
throttle grip and cableThe operation of the throttle grip should
be checked before each ride. In addition,
the cable should be lubricated at the
intervals specified in the periodic
maintenance chart.
EAU23140
Checking and lubricating the
brake and clutch levers
1
2
1. Brake lever
2. Lubrication point1. Clutch lever
2. Lubrication pointThe operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be
lubricated if necessary.
cap 6.pmd 18/4/2007, 14:35
21

6-24
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23280
Checking the steeringWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.1. Place a stand under the engine to raise the front wheel off the ground.
EWA10750
Securely support the motorcycle so
that there is no danger of it falling
over.2. Hold the lower ends of the front forklegs and try to move them forward
and backward. If any free play can
be felt, have a Yamaha dealer
check or repair the steering.
EAU23290
Checking the wheel bearingsThe front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrication
chart. If there is play in the wheel hub or
if the wheel does not turn smoothly,
have a Yamaha dealer check the wheel
bearings.
EAUW0100
BatteryThe battery is located under the seat.
(See page 3-9).
This model is equipped with a sealed
type (MF) battery, which does not require
any maintenance. There is no need to
check the electrolyte or to add distilled
water.
ECA10620
Never attempt to remove the battery
cell seals, as this would permanently
damage the battery.
EWA10760
l
l l
l
l
Electrolyte is poisonous and
dangerous since it contains
sulfuric acid, which causes
severe burns. Avoid any contact
with skin, eyes or clothing and
always shield your eyes when
working near batteries. In case
of contact, administer the
following FIRST AID.l
l l
l
l
EXTERNAL: Flush with plenty
of water.
l
l l
l
l
INTERNAL: Drink large
cap 6.pmd 24/1/2007, 14:38
24

6-29
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU24350
Supporting the motorcycleSince this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear wheel
or performing other maintenance
requiring the motorcycle to stand upright.
Check that the motorcycle is in a stable
and level position before starting any
maintenance. A strong wooden box can
be placed under the engine for added
stability.
To service the front wheel1. Stabilize the rear of the motorcycle by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack
under the frame in front of the rear
wheel.
2. Raise the front wheel off the ground by using a motorcycle stand.
To service the rear wheel
Raise the rear wheel off the ground by
using a motorcycle stand or, if a
motorcycle stand is not available, by
placing a jack either under each side of
the frame in front of the rear wheel or
under each side of the swingarm.
EAU24360
Front wheel
EAUW0180
To remove the front wheel
EWA10820
l
l l
l
l
It is advisable to have a Yamaha
dealer service the wheel.
l
l l
l
l
Securely support the motorcycle
so that there is no danger of it
falling over.
1. Loosen the front wheel axle pinch
bolt and the wheel axle.1 2
1. Wheel axle
2. Wheel axle pinch bolt
2. Lift the front wheel off the ground
according to the procedure on page
6-29.
3. Pull the wheel axle out, and then remove the wheel.
ECA11070
Do not apply the brake after the wheel
has been removed together with the
brake disc, otherwise the brake pads
will be forced shut.
EAUW0160
To install the front wheel1. Lift the wheel up between the fork legs.Make sure that there is enough space
between the brake pads before inserting
the brake disc into the caliper.2. Insert the wheel axle.
3. Lower the front wheel so that it ison the ground.
4. Tighten the wheel axle to the specified torque.
cap 6.pmd 24/1/2007, 14:38
29

6-32
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU25901
Troubleshooting chart
EWA10840
Keep away open flames and do not smoke while checking or working on the \
fuel system.
Check the fuel level in
the fuel tank.1. Fuel
There is enough fuel.There is no fuel.
Check the compression.
Supply fuel.
The engine does not start.
Check the compression.
Operate the electric starter.2. Compression
There is compression.
There is no compression.
Check the ignition. Have a Yamaha dealer
check the vehicle.
Remove the spark plug
and check the electrodes.3. Ignition
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Have a Yamaha dealer check the vehicle.
The engine does not start.
Have a Yamaha dealer
check the vehicle.
The engine does not start.
Check the battery.
Operate the electric starter.4. Battery
The engine turns over
quickly.
The engine turns over
slowly.
The battery is good.Check the battery lead connections,
and charge the battery if necessary.
DryWet
Open the throttle halfway and operate
the electric starter.
cap 6.pmd 24/1/2007, 14:38
32