engine oil YAMAHA YBR250 2007 Owners Manual

TABLE OF CONTENTESSAFETY INFORMATION .................... 1-1
DESCRIPTION ................................... 2-1Left view ........................................ 2 - 1
Right view ...................................... 2 - 2
Controls and instruments ............. 2 - 3
INSTRUMENT AND CONTROL
FUNCTIONS ....................................... 3-1 Main switch/steering lock ............. 3 - 1
Indicator and warning lights ........ 3 - 2
Speedometer ................................. 3 - 2
Tachometer .................................... 3 - 3
Multi-function display ................... 3 - 3
Handlebar switches ...................... 3 - 4
Clutch lever ................................... 3 - 5
Shift pedal ..................................... 3 - 6
Brake lever .................................... 3 - 6
Brake pedal ................................... 3 - 6
Fuel tank cap ................................. 3 - 7
Fuel ................................................ 3 - 7
Catalytic converter ........................ 3 - 8
Seat ................................................ 3 - 9
Helmet holder ................................ 3 - 9
Storage compartment .................3-10
Adjusting the shock aborber
assemblies ............................... 3-10
Luggage strap holders ...............3-11
Sidestand ..................................... 3-11
Ignition circuit cut-off system .....3-12 PRE-OPERATION CHECKS .............. 4-1
Pre-operation check list ............... 4 - 2
OPERATION AND IMPORTANT
RIDING POINTS ................................. 5-1 Starting the engine ....................... 5 - 1
Shifting ........................................... 5 - 2
Tips for reducing fuel
consumption .............................. 5 - 3
Engine break-in ............................ 5 - 3
Parking .......................................... 5 - 4
PERIODIC MAINTENANCE AND
MINOR REPAIR .................................. 6-1 Owner’s tool kit .............................. 6 - 1
Periodic maintenance and lubrication chart ......................... 6 - 2
Removing and installing the cowling and panels ................... 6 - 6
Checking the spark plug .............. 6 - 7
Engine oil and oil filter element ... 6-8
Cleaning the air filter element ... 6-11
Checking the engine idling
speed ........................................ 6-12
Checking the throttle cable free play .................................... 6-12
Valve clearance .. ........................6-12
Tires ............................................. 6-13
Cast wheels ................................. 6-15
Adjusting the clutch lever free play .................................... 6-15Adjusting the brake pedal
position and free play .............6-16
Adjusting the rear brake light switch ........................................ 6-17
Checking the front brake pads
and rear brake shoes ..............6-17
Checking the front brake fluid level .......................................... 6-18
Changing the brake fluid ...........6-18
Drive chain slack ........................6-19
Cleaning and lubricating the
drive chain ............................... 6-20
Checking and lubricating the cables ....................................... 6-21
Checking and lubricating the throttle grip and cable .............6-21
Checking and lubricating the
brake and clutch levers ...........6-21
Checking and lubricating the brake and shift pedals ............6-22
Checking and lubricating the sidestand .................................. 6-22
Lubricating the rear
suspension .............................. 6-23
Checking the front fork ...............6-23
Checking the steering ................6-24
Checking the wheel bearings ....6-24
Battery .......................................... 6-24
Replacing the fuses ....................6-26
Replacing the headlight bulb ....6-27
Replacing a turn signal light bulb or the tail/brake light bulb .......6-28
indice.pmd 24/1/2007, 14:37
1

2-1
2
DESCRIPTION
EAU10410
Left view1. Idle adjusting screw
2. Battery
3. Main fuse
4. Fuse box
5. Storage compartment
6. Grab bar
7. Seat lock
8. Shift pedal
9. Engine oil drain bolt
cap 2.pmd24/1/2007, 14:37
1

2-2
2
DESCRIPTION
EAU10420
Right view1. Owner’s tool kit
2. Air filter element
3. Front brake fluid reservoir
4. Engine oil filter element
5. Engine oil filler cap
6. Brake pedal
7. Shock absorber assembly spring preload adjusting ring
cap 2.pmd24/1/2007, 14:37
2

5-3
5
OPERATION AND IMPORTANT RIDING POINTS
EAU16810
Tips for reducing fuel
consumptionFuel consumption depends largely on
your riding style. Consider the following
tips to reduce fuel consumption:l
Shift up swiftly, and avoid high
engine speeds during acceleration.
l
Do not rev the engine while shifting
down, and avoid high engine
speeds with no load on the engine.
l
Turn the engine off instead of letting
it idle for an extended length of time
(e.g., in traffic jams, at traffic lights
or at railroad crossings).
EAU16841
Engine break-inThere is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the
following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throttle
operation or any condition that might
result in engine overheating must be
avoided.
EAU17100
0-1000 km (0-600 mi)
Avoid prolonged operation above 5000
r/min.
1000-1600 km (600-1000 mi)
Avoid prolonged operation above 6000
r/min.
ECA11150
After 1000 km (600 mi) of operation,
the engine oil must be changed, and
the oil filter element replaced.
1600 km (1000 mi) and beyond
The vehicle can now be operated
normally.
ECA10310
l
l l
l
l
Keep the engine speed out of the
tachometer red zone.
l
l l
l
l
If any engine trouble should
occur during the engine break-
in period, immediately have a
Yamaha dealer check the vehicle.
cap 5.pmd 24/1/2007, 14:37
3

6-8
6
PERIODIC MAINTENANCE AND MINOR REPAIRSpecified spark plug:NGK / DR8EATo install the spark plug
1. Measure the spark plug gap with a wire thickness gauge and, if
necessary, adjust the gap to
specification.1. Spark plug gapSpark plug gap:0.6~0.7mm (0.024-0.028 in)2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
3. Install the spark plug with the spark plug wrench, and then
tighten it to the specified torque. Tightening torque:
Spark plug:17.5 Nm (1.75 m.kgf, 13 ft.lbt)
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4-1/2 turn past
finger tight. However, the spark plug
should be tightened to the specified
torque as soon as possible.4. Install the spark plug cap.
5. Install the cowling.
EAU37801
Engine oil and oil filter
elementThe engine oil level should be checked
before each ride. In addition, the oil must
be changed and the oil filter element
replaced at the intervals specified in the
General periodic maintenance and
lubrication chart.
To check the engine oil level 1. Place the vehicle on a level surface and hold it in an upright
position.Make sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.2. Start the engine, warm it up forseveral minutes, and then turn it
off.
3. Wait a few minutes until the oil settles, and then check the oil level
through the check window located
at the bottom-right side of the
crankcase.
cap 6.pmd 24/1/2007, 14:37
8

6-9
6
PERIODIC MAINTENANCE AND MINOR REPAIR
The engine oil should be between the
minimum and maximum level marks.
12
3
1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark4. If the engine oil is below the minimum level mark, add sufficient
oil of the recommended type to
raise it to the correct level.
To change the engine oil (with or
without oil filter element
replacement) 1. Start the engine, warm it up for several minutes, and then turn it
off.
2. Place an oil pan under the engine to collect the used oil.
1
1. Dipstick3. Remove the engine oil filler bolt anddrain bolt to drain the oil from the
crankcase.
-2-3-4-5
1
1. Engine oil drain boltCheck the washer for damage and
replace it if necessary.
4. Remove the oil filter element drainbolt to drain the oil from the oil filter
element.Skip steps 5-7 if the oil filter element is
not being replaced.5. Remove the oil filter element coverby removing the bolts.1. Oil filter element cover bolts
2. Oil filter element drain bolt6. Remove and replace the oil filterelement and O-rings.
cap 6.pmd 24/1/2007, 14:37
9

6-10
6
PERIODIC MAINTENANCE AND MINOR REPAIR
2
2
1
1. Oil filter element
2. O-ringMake sure that the O-rings are properly
seated.7. Install the oil filter element coverby installing the bolts, then
tightening them to the specified
torque.Tightening torque:Oil filter element cover bolt: 10 Nm (1,0 m.kgf, 7.4 ft.lbf)8. Install the engine oil drain bolt, and
then tighten it to the specified
torque.
9. Install the oil filter element drain bolt, and then tighten it to the
specified torque.
Tightening torque:Engine oil drain bolt: 20 Nm (2.0 m.kgf, 15 ft.lbf)
Oil filter element drain bolt: 7 Nm (0.7 m.kgf, 5.25 ft.lbf)10. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler bolt.Recommended engine oil:See page 8-1
Oil quantity: Without oil filter element
replacement:1.35 L (1.43 US qt) (1.19
Imp.qt)
With oil filter element replacement:1.45 L (1.53 US qt) (1.28
Imp.qt)
ECA11620
l
l l
l
l
In order to prevent clutch
slippage (since the engine oil
also lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
l
l l
l
l
Make sure that no foreign
material enters the crankcase.
11. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off and
check for the cause.
12. Turn the engine off, and then check the oil level and correct it if
necessary.
cap 6.pmd 24/1/2007, 14:37
10

6-11
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU20880
Cleaning the air filter elementThe air filter should be cleaned at the
specified intervals. It should be cleaned
more frequently when riding in unusually
wet or dusty areas.1. Remove panel B. (See page 6-6.)
1 2
2
1. Air filter case cover
2. Screw2. Remove the air filter case by
removing the screws.
3. Remove the air filter from the case.
1
1. Air filter element
4. Remove the air filter element from its guide and clean it with solvent.
After cleaning, remove the
remaining solvent by squeezing
the element.5. Apply recommended oil to theentire surface of the element and
squeeze out the excess oil. It
should be wet but not dripping.Recommended oil:Engine oil6. Insert the air filter element guide
into the air filter and install it in the
case.
7. Install the air filter case cover and panel by installing the screws.
ECA10480
l
l l
l
l
Make sure that the air filter
element is properly seated in the
air filter case.
l
l l
l
l
The engine should never be
operated without the air filter
element installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.
cap 6.pmd 24/1/2007, 14:37
11

6-20
6
PERIODIC MAINTENANCE AND MINOR REPAIRTightening torques:Locknut:
16 Nm (1.6 m.kgf, 12 ft.lbt)
Axle nut: 104 Nm (10.4 m.kgf, 77 ft.lbt)4. Adjust the brake pedal free play.
(See page 6-16.)
EWA10660
After adjusting the brake pedal free
play, check the operation of the brake
light.
EAU23022
Cleaning and lubricating the
drive chainThe drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrication
chart, otherwise it will quickly wear out,
especially when riding in dusty or wet
areas. Service the drive chain as follows.
ECA10581
The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.1. Clean the drive chain with keroseneand a small soft brush.
ECA11120
To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain
lubricant.
ECA11110
Do not use engine oil or any other
lubricants for the drive chain, as they
may contain substances that could
damage the O-rings.
cap 6.pmd
24/1/2007, 14:38
20

6-21
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23100
Checking and lubricating the
cablesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the
cables and cable ends should be
lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or replace
it.Recommended lubricant:Engine oil
EWA10720
Damage to the outer sheath may
interfere with proper cable operation
and will cause the inner cable to rust.
Replace a damaged cable as soon as
possible to prevent unsafe
conditions.
EAU23111
Checking and lubricating the
throttle grip and cableThe operation of the throttle grip should
be checked before each ride. In addition,
the cable should be lubricated at the
intervals specified in the periodic
maintenance chart.
EAU23140
Checking and lubricating the
brake and clutch levers
1
2
1. Brake lever
2. Lubrication point1. Clutch lever
2. Lubrication pointThe operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be
lubricated if necessary.
cap 6.pmd 18/4/2007, 14:35
21