ABS YAMAHA YZ250F 2008 Owner's Manual

5-41
REAR SHOCK ABSORBER
• Bolt [rear frame (lower)] "3"
7. Tighten: • Bolt (air filter joint) "1" Bolt [rear frame (lower)]:
32 Nm (3.2 m•kg, 23
ft•lb)
Bolt (air filter joint): 3 Nm (0.3 m•kg, 2.2
ft•lb)

7-8
CHASSIS
When using a rear shock absorber
other than currently installed, use
the one whose overall length "a"
does not exceed the standard as it
may result in faulty performance.
Never use one whose overall
length is greater than standard.
REAR SHOCK ABSORBER
SETTING PARTS
• Rear shock spring "1"
[Equal-pitch titanium spring]
[Equal-pitch steel spring][Unequal-pitch steel spring]
Install the spring seat "2" to the ti-
tanium spring.
• The unequal-pitch spring is softer in
initial characteristic than the equal-
pitch spring and is difficult to bottom
out under full compression.
• The I.D. mark "a" is marked at the end of the spring.
• Spring specification varies accord-
ing to the color and quantity of I.D.
marks.
• Extent of adjustment (spring length) [Titanium spring]
[Steel spring]
Length "a" of standard
shock:
490 mm (19.29 in)
T
Y
P
E SPRI
NG
RAT
E SPRING
PART
NUM-
BER -
22212- I.D.
MARK SPR
ING
FRE E
LEN
GTH
(ap-
prox
.)
S
O F
T 4.5 1C3-00 Green 265
4.7 1C3-10 Red 265
4.9 1C3-20 Black 265
5.1 1C3-30 Blue 265
S T
D 5.3
1C3-40
(1C3-A0) Yellow 275
S
TI
F
F 5.5 1C3-50 Pink 275
5.7 1C3-60 White 275
T
Y
P
E SPRI
NG
RAT
E SPRING
PART NUM-
BER -
22212- I.D.
MARK/
Q'TY SPR
ING
FRE E
LEN
GTH
4.3 5UN-00 Brown/1 260
T
Y
P
E SPRI
NG
RAT
E
(ap-
prox. ) SPRING
PART
NUM-
BER -
22212- I.D.
MARK/ Q'TY SPR
ING
FRE E
LEN
GTH
S
O
F
T 4.5 5UN-A0 Green/2 275
4.75UN-B0Red/2275
4.9 5UN-C0 Black/2 275
5.1 5UN-D0 Blue/2 275
5.3 5UN-E0
Yellow/
2 275
5.5 5UN-F0 Pink/2 275
S
TI F
F 5.7
5UN-
22212- G0 White/2 275
SPRING
FREE
LENGTH EXTENT OF AD-
JUSTMENT "b"
Approx. 265 mm
(10.43 in) One I.D. mark
245.5–263.5 mm (9.67–10.37 in)
Two I.D. marks
251.5–269.5 mm (9.90–10.61 in)
Three I.D. marks 243.0–261.0 mm (9.57–10.28 in)
Approx. 275 mm
(10.83 in) One I.D. mark
255.5–273.5 mm (10.06–10.77 in)
Two I.D. marks
261.5–279.5 mm (10.30–11.00 in)
Three I.D. marks 253.0–271.0 mm (9.96–10.67 in)
SPRING FREE
LENGTH EXTENT OF AD-
JUSTMENT "b"
260 mm
(10.24 in) 240.5–258.5 mm
(9.47–10.18 in)
275 mm
(10.83 in) 255.5–273.5 mm
(10.06–10.77 in)

7-9
CHASSIS
SUSPENSION SETTING (FRONT FORK)
• If any of the following symptoms is experienced with the standard position as the base, make resetting by reference to the adjustment procedure given in the same chart.
• Before any change, set the rear shock absorber sunken length to the standard figure 90–100 mm (3.5–3.9 in).
Symptom Section
Check Adjust
Jump Large
gap Medi-
um
gap Small
gap
Stiff over entire
range
â—‹â—‹â—‹
Compression damping Turn adjuster counterclockwise (about 2 clicks) to decrease damping.
Oil amount Decrease oil amount by about 5–10 cm
3 (0.2–0.4
Imp oz, 0.2–0.3 US oz).
Spring Replace with soft spring.
Unsmooth move-
ment over entire
range
â—‹â—‹â—‹â—‹
Outer tube Check for any bends, dents, and other noticeable
scars, etc. If any, replace affected parts.
Inner tube
Slide metal Replace with a new one for extended use.
Piston metal Replace with a new one for extended use.
Under bracket tighten-
ing torque Retighten to specified torque.
Poor initial move-
ment
â—‹
Rebound damping Turn adjuster counterclockwise (about 2 clicks) to decrease damping.
Oil seal Apply grease in oil seal wall.
Soft over entire
range, bottoming
out
â—‹â—‹
Compression damping Turn adjuster clockwise (about 2 clicks) to in- crease damping.
Oil amount Increase oil amount by about 5–10 cm
3 (0.2–0.4
Imp oz, 0.2–0.3 US oz).
Spring Replace with stiff spring.
Stiff toward stroke
end
â—‹Oil amount Decrease oil amount by about 5 cm3 (0.2 Imp
oz,0.2 US oz).
Soft toward stroke
end, bottoming out
â—‹Oil amount Increase oil amount by about 5 cm3 (0.2 Imp
oz,0.2 US oz).
Stiff initial move-
ment
â—‹â—‹â—‹â—‹Compression damping Turn adjuster counterclockwise (about 2 clicks) to
decrease damping.
Low front, tending to
lower front posture
â—‹â—‹
Compression damping Turn adjuster clockwise (about 2 clicks) to in- crease damping.
Rebound damping Turn adjuster counterclockwise (about 2 clicks) to decrease damping.
Balance with rear end Set sunken length for 95–100 mm (3.7–3.9 in) when one passenger is astride seat (lower rear
posture).
Oil amount Increase oil amount by about 5 cm
3 (0.2 Imp oz,
0.2 US oz).
"Obtrusive" front,
tending to upper
front posture
â—‹â—‹
Compression damping Turn adjuster counterclockwise (about 2 clicks) to decrease damping.
Balance with rear end Set sunken length for 90–95 mm (3.5–3.7 in) when one passenger is astride seat (upper rear
posture).
Spring Replace with soft spring.
Oil amount Decrease oil amount by about 5–10 cm
3 (0.2–0.4
Imp oz, 0.2–0.3 US oz).

7-10
CHASSIS
SUSPENSION SETTING (REAR SHOCK ABSORBER)
• If any of the following symptoms is experienced with the standard position as the base, make resetting by reference to the adjustment procedure given in the same chart.
• Adjust the rebound damping in 2-click increments or decrements.
• Adjust the low compression damping in 1-click increments or decrements.
• Adjust the high compression damping in 1/6 turn increments or decrements.
Symptom Section
Check Adjust
Jump Large
gap Medi-
um
gap Small
gap
Stiff, tending to sink
â—‹â—‹
Rebound damping Turn adjuster counterclockwise (about 2 clicks) to decrease damping.
Spring set length Set sunken length for 90–100 mm (3.5–3.9 in) when one passenger is astride seat.
Spongy and unsta-
ble
â—‹â—‹
Rebound damping Turn adjuster clockwise (about 2 clicks) to in- crease damping.
Low compression
damping Turn adjuster clockwise (about 1 click) to increase
damping.
Spring Replace with stiff spring.
Heavy and dragging
â—‹â—‹
Rebound damping Turn adjuster counterclockwise (about 2 clicks) to decrease damping.
Spring Replace with soft spring.
Poor road gripping
â—‹
Rebound damping Turn adjuster counterclockwise (about 2 clicks) to decrease damping.
Low compression
damping Turn adjuster clockwise (about 1 clicks) to in-
crease damping.
High compression
damping Turn adjuster clockwise (about 1/6 turn) to in-
crease damping.
Spring set length Set sunken length for 90–100 mm (3.5–3.9 in) when one passenger is astride seat.
Spring Replace with soft spring.
Bottoming out
â—‹â—‹
High compression
damping Turn adjuster clockwise (about 1/6 turn) to in-
crease damping.
Spring set length Set sunken length for 90–100 mm (3.5–3.9 in) when one passenger is astride seat.
Spring Replace with stiff spring.
Bouncing
â—‹â—‹
Rebound damping Turn adjuster clockwise (about 2 clicks) to in- crease damping.
Spring Replace with soft spring.
Stiff travel
â—‹â—‹
High compression
damping Turn adjuster counterclockwise (about 1/6 turn) to
decrease damping.
Spring set length Set sunken length for 90–100 mm (3.5–3.9 in) when one passenger is astride seat.
Spring Replace with soft spring.