ABS YAMAHA YZF-R1M 2017 User Guide

Periodic maintenance and adjustment
7-6
1
2
3
4
5
67
8
9
10
11
12
12 Drive chain Check chain slack, alignment and
condition.
Adjust and lubricate chain with a special O-ring chain lubricant
thoroughly. Every 800 km (500 mi) and after washing the motorcycle, riding in the rain or
riding in wet areas
13 *Steering bearings Check bearing assemblies for
looseness.  
Moderately repack with lithium-soap-based grease. 
14 *Steering damper Check operation and for oil
leakage. 
15 *Chassis fasteners Make sure that all nuts, bolts and
screws are properly tightened. 
16 Brake lever pivot
shaft Lubricate with silicone grease.

17 Brake pedal pivot
shaft Lubricate with lithium-soap-based
grease. 
18 Clutch lever pivot
shaft Lubricate with lithium-soap-based
grease. 
19 Shift pedal pivot
shaft Lubricate with lithium-soap-based
grease. 
20 Sidestand Check operation.
Lubricate with lithium-soap-based
grease. 
21 *Sidestand switch Check operation and replace if
necessary. 
22 *Front fork Check operation and for oil
leakage.
Replace if necessary. 
23 *Shock absorber
assembly Check operation and for oil
leakage.
Replace if necessary. 
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 10000 km
(6000 mi) 20000 km
(12000 mi) 30000 km
(18000 mi) 40000 km
(24000 mi)BX4-9-E0.book 6 ページ ２０１６年１２月１日　木曜日　午後８時７分

Periodic maintenance and adjustment
7-34
1
2
3
4
5
67
8
9
10
11
12
NOTICE
ECA16522
To charge a VRLA (Valve Regulated
Lead Acid) battery, a special (con-
stant-voltage) battery charger is re-
quired. Using a conventional batterycharger will damage the battery.
To store the battery 1. If the vehicle will not be used for more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
NOTICE: When removing the
battery, be sure the key is
turned to “OFF”, then discon-
nect the negative lead before
disconnecting the positive
lead.
[ECA16303]
2. If the battery will be stored for more than two months, check it at least
once a month and fully charge it if
necessary.
3. Fully charge the battery before in- stallation. NOTICE: When install-
ing the battery, be sure the key
is turned to “OFF”, then con-
nect the positive lead before connecting the negative
lead.
[ECA16841]
4. After installation, make sure that
the battery leads are properly con-
nected to the battery terminals.NOTICE
ECA16531
Always keep the battery charged.
Storing a discharged battery cancause permanent battery damage.
EAU66592
Replacing the fusesThe main fuse and ABS motor fuse are
located under the rider seat.
To access the ABS motor fuse1. Remove the passenger seat andrider seat. (See page 4-37.)
2. Remove the panel by removing the screws.1. Main fuse
2. ABS motor fuse
3. Starter relay cover
4. ABS motor spare fuse1 2
4
3
BX4-9-E0.book 34 ページ ２０１６年１２月１日　木曜日　午後８時７分

Periodic maintenance and adjustment7-35
1
2
3
4
5
678
9
10
11
12
3. Remove the starter relay cover by
pulling it upward.
The fuse boxes, which contain the fus-
es for the individual circuits, are located
under panel A. (See page 7-9.) If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off the electrical circuit in question.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.
[EWA15132]
1. Screw
2. Panel
1. Starter relay cover1 1
2
1
1. Hazard fuse
2. Fuel injection system fuse
3. Electronic throttle valve fuse
4. Backup fuse
5. Sub radiator fan motor fuse
6. Radiator fan motor fuse
7. Spare fuse
1
2
3
4
5
6 7
1. Ignition fuse
2. Signaling system fuse
3. ABS ECU fuse
4. ABS solenoid fuse
5. Headlight fuse
6. Terminal fuse 1
7. Spare fuse
8. SCU fuse (YZF-R1M)
1
23
45
6
7
8
7
BX4-9-E0.book 35 ページ ２０１６年１２月１日　木曜日　午後８時７分

Periodic maintenance and adjustment
7-36
1
2
3
4
5
67
8
9
10
11
12 3. Turn the key to “ON” and turn on
the electrical circuit in question to check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
EAU67121
Vehicle lightsThis model is equipped with full-LED
lighting.
The headlights, auxiliary lights, turn sig-
nals, tail/brake light, and license plate
light are all LED. There are no user re-
placeable bulbs.
If a light does not come on, check the
fuses and then have a Yamaha dealer
check the vehicle.NOTICE
ECA16581
Do not affix any type of tinted film orstickers to the headlight lens.
Specified fuses:Main fuse:50.0 A
Terminal fuse 1:
2.0 A
Headlight fuse: 7.5 A
Signaling system fuse: 7.5 A
Ignition fuse:
15.0 A
Radiator fan motor fuse: 15.0 A
Sub radiator fan motor fuse: 10.0 A
ABS motor fuse:
30.0 A
Hazard fuse: 7.5 A
ABS ECU fuse: 7.5 A
ABS solenoid fuse:
15.0 A
SCU fuse: 7.5 A (YZF-R1M)
Fuel injection system fuse: 15.0 A
Backup fuse: 7.5 A
Electronic thrott le valve fuse:
7.5 A
1. Auxiliary light
2. Headlight
12
1
2
BX4-9-E0.book 36 ページ ２０１６年１２月１日　木曜日　午後８時７分

Motorcycle care and storage
8-3
1
2
3
4
5
6
789
10
11
12
tergent, alkaline products and a
soft brush may be used.

Never use compounds or other
special treatments to clean the tita-
nium muffler, as they will remove
the finish on the outer surface of
the muffler.

Even the smallest amounts of oil,
such as from oily towels or finger-
prints, will leave stains on the tita-
nium muffler, which can be
removed with a mild detergent.

Note that the thermally induced
discoloring of the portion of the ex-
haust pipe leading into the titanium
muffler is normal and cannot be re-
moved.
After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Immediately dry the drive chain and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine chrome, aluminum and stain-
less-steel parts.
4. To prevent corrosion, it is recom- mended to apply a corrosion pro- tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean- er to remove any remaining dirt.
6. Touch up minor paint damage caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.
WARNING
EWA11132
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.

If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
NOTICE
ECA10801

Apply spray oil and wax spar- ingly and make sure to wipe off
any excess.

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from thelens.
BX4-9-E0.book 3 ページ ２０１６年１２月１日　木曜日　午後８時７分

Specifications
9-2
1
2
3
4
5
6
7
89
10
11
12
3rd: 1.842 (35/19)
4th:
1.579 (30/19)
5th: 1.381 (29/21)
6th: 1.250 (30/24)
Chassis:Frame type: Diamond
Caster angle: 24.0 
Trail:
102 mm (4.0 in)Front tire:Type:Tubeless
Size:
120/70 ZR17MC (58W)
Manufacturer/model: BRIDGESTONE/BATTLAX RACING
STREET RS10FRear tire:Type:
Tubeless
Size:
190/55 ZR17M/C (75W) (YZF-R1)
200/55 ZR17M/C (78W) (YZF-R1M)
Manufacturer/model:
BRIDGESTONE/BATTLAX RACING
STREET RS10R
Loading:Maximum load:187 kg (412 lb)
* (Total weight of rider, passenger, cargo and accessories)Tire air pressure (measured on cold
tires):
Front: 250 kPa (2.50 kgf/cm
2, 36 psi)
Rear: 290 kPa (2.90 kgf/cm2, 42 psi)
Front wheel:Wheel type:Cast wheel
Rim size: 17M/C x MT3.50Rear wheel:Wheel type:Cast wheel
Rim size: 17M/C x MT6.00Unified brake system:Operation:Activated by front brakeFront brake:Type:
Hydraulic dual disc brake
Specified brake fluid: DOT 4Rear brake:Type:
Hydraulic single disc brake
Specified brake fluid: DOT 4
Front suspension:Type:
Telescopic fork
Spring: Coil spring
Shock absorber: Hydraulic damper
Wheel travel:
120 mm (4.7 in)Rear suspension:Type:Swingarm (link suspension)
Spring:
Coil spring
Shock absorber: Gas-hydraulic damper
Wheel travel: 120 mm (4.7 in)Electrical system:System voltage:12 V
Ignition system: TCI
Charging system:
AC magnetoBattery:Model:YTZ7S
Voltage, capacity:
12 V, 6.0 Ah (10 HR)Bulb wattage:Headlight:LED
BX4-9-E0.book 2 ページ ２０１６年１２月１日　木曜日　午後８時７分

Specifications
9-3
1
2
3
4
5
6
7
8910
11
12
Brake/tail light:LED
Front turn signal light:
LED
Rear turn signal light: LED
Auxiliary light: LED
License plate light:
LED
Meter lighting: LED
Neutral indicator light: LED
High beam indicator light:
LED
Turn signal indicator light: LED
Stability control indicator light:
LED
Oil pressure and coolant temperature warning
light:
LED
Fuel level warning light:
LED
Coolant temperature warning light: LED
Engine trouble warning light: LED
Steering damper and suspension warning
light:
LED
ABS warning light:
LED Immobilizer system indicator light:
LED
Shift timing indicator light:
LED
Fuse(s):Main fuse:50.0 A
Terminal fuse 1:
2.0 A
Headlight fuse: 7.5 A
Signaling system fuse: 7.5 A
Ignition fuse:
15.0 A
Radiator fan motor fuse: 15.0 A
Sub radiator fan motor fuse: 10.0 A
Hazard fuse:
7.5 A
ABS ECU fuse: 7.5 A
Fuel injection system fuse: 15.0 A
SCU fuse:
7.5 A (YZF-R1M)
ABS motor fuse: 30.0 A
ABS solenoid fuse: 15.0 A
Backup fuse:
7.5 A Electronic throttle valve fuse:
7.5 A
BX4-9-E0.book 3 ページ ２０１６年１２月１日　木曜日　午後８時７分

11-1
1
2
3
4
5
6
7
8
9
1011
12
IndexAABS warning light.................................... 4-6
Air filter element .................................... 7-18
Auxiliary DC connector ......................... 4-46BBattery................................................... 7-33
Brake and clutch levers, checking and lubricating ........................................... 7-30
Brake and shift pedals, checking and lubricating ........................................... 7-29
Brake fluid, changing ............................ 7-26
Brake fluid level, checking .................... 7-25
Brake lever ............................................ 4-31
Brake lever free play, checking ............. 7-24
Brake light switches .............................. 7-24
Brake pedal ........................................... 4-31
Brake system ........................................ 4-32CCables, checking and lubricating .......... 7-29
Canister................................................. 7-13
Care ........................................................ 8-1
Catalytic converter ................................ 4-36
CCU ...................................................... 4-38
Clutch lever ........................................... 4-30
Clutch lever free play, adjusting ............ 7-23
Coolant.................................................. 7-16
Cowlings and panels, removing and installing................................................ 7-9DData recording, vehicle ......................... 10-2
Diagnostic connector ............................ 10-2
Dimmer switch ........................................ 4-4
Display, main screen............................... 4-9
Display, menu screen ........................... 4-15 Document storage ................................ 4-39
Drive chain, cleaning and lubricating .... 7-28
Drive chain slack .................................. 7-27
EEngine break-in ...................................... 6-3
Engine idling speed, checking .............. 7-19
Engine oil and oil fi
lter cartridge ........... 7-13
Engine serial number............................ 10-1
Engine trouble warning light ................... 4-6
EXUP system ....................................... 4-46FFront and rear brake pads, checking .... 7-25
Front fork, adjusting .............................. 4-40
Front fork, checking .............................. 7-31
Fuel....................................................... 4-34
Fuel consumption, tips for reducing........ 6-3
Fuel level warning light ........................... 4-6
Fuel tank breather hose and overflow hose ................................................... 4-36
Fuel tank cap ........................................ 4-33
Fuses, replacing ................................... 7-34GGlossary ................................................. 3-3HHandlebar switches ................................ 4-3
Hazard switch ......................................... 4-4
High beam indicator light ........................ 4-6
Horn switch ............................................. 4-4IIdentification numbers .......................... 10-1
Ignition circuit cut-off system ................ 4-47
Immobilizer system ................................. 4-1
Immobilizer system indicator light........... 4-7
Indicator lights and warning lights .......... 4-6
MMain switch/steering lock ........................ 4-2
Maintenance and lubrication, periodic..... 7-5
Maintenance, emission control system ... 7-3
Matte color, caution ................................. 8-1
Model label ............................................ 10-2NNeutral indicator light .............................. 4-6OOil pressure and coolant temperature warning light.......................................... 4-8PParking .................................................... 6-4
Part locations .......................................... 2-1
Pass/LAP switch ..................................... 4-4RRear view mirrors .................................. 4-40SSafety information ................................... 1-1
Seats ..................................................... 4-37
Shifting .................................................... 6-2
Shift pedal ............................................. 4-30
Shift timing indicator light ........................ 4-7
Shock absorber assembly, adjusting .... 4-42
Sidestand .............................................. 4-47
Sidestand, checking an d lubricating...... 7-31
Spark plugs, checking ........................... 7-12
Special features ...................................... 3-1
Specifications .......................................... 9-1
Stability control indicator light.................. 4-7
Starting the engine .................................. 6-1
Steering, checking................................. 7-32
Steering damper and suspension
warning light.......................................... 4-8
BX4-9-E0.book 1 ページ ２０１６年１２月１日　木曜日　午後８時７分