warning light YAMAHA YZF-R1SC 2004 Service Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2004, Model line: YZF-R1SC, Model: YAMAHA YZF-R1SC 2004Pages: 457, PDF Size: 7.58 MB
Page 18 of 457
1-2
1
1 Clock
2 Speedometer
3 “SELECT” button
4 “RESET” button
5 Tachometer
6 Coolant temperature display / air intake
temperature display
7 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
8 Shift timing indicator light
1 Clock
2 Speedometer
FEATURES
GEN
INFO
NOTE:
EAS00019
FEATURES
INSTRUMENT FUNCTIONS
Multi-function display
The multi-function meter unit is equipped with
the following:
a speedometer (which shows the riding
speed)
a tachometer (witch shows engine speed)
an odometer (which shows the total distance
traveled)
two tripmeters (which show the distance
traveled since they were last set to zero)
a fuel reserve tripmeter (which shows the
distance traveled since the fuel level warning
light came on)
a stopwatch
a clock
a coolant temperature display
an air intake temperature display
a self-diagnosis device
a display brightness and shift timing indicator
light control mode
Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons.
Clock mode
Turn the key to “ON”.
To set the clock
1. Push the “SELECT” button and “RESET”
button together for at least two seconds.
2. When the hour digits start flashing, push the
“RESET” button to set the hours.
3. Push the “SELECT” button, and the minute
digits will start flashing.
4. Push the “RESET” button to set the minutes.
5. Push the “SELECT” button and then release
it to start the clock.
ProCarManuals.com
Page 19 of 457
1-3
FEATURES
GEN
INFO
1 Coolant temperature display / air intake
temperature display
2 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
3 Shift timing indicator light
NOTE:
NOTE:Odometer, tripmeter, and stopwatch modes
Push the “SELECT” button to switch the display
between the odometer mode “ODO”, the trip-
meter modes “TRIP A” and “TRIP B” and the
stopwatch mode in the following order:
TRIP A TRIP B ODO Stopwatch
TRIP A
If the fuel level warning light comes on, the
odometer display will automatically change to
the fuel reserve tripmeter mode ”F-TRIP” and
start counting the distance traveled from that
point. In that case, push the ”SELECT” button to
switch the display between the various tripme-
ter, odometer, and stopwatch modes in the fol-
lowing order:
F-TRIP Stopwatch TRIP A TRIP B
ODO F-TRIP
To reset a tripmeter, select it by pushing the “SE-
LECT” button, and then push the “RESET” button
for at least one second. If you do not reset the fuel
reserve tripmeter manually, it will reset itself auto-
matically and the display will return to the prior
mode after refueling and traveling 5 km (3 mi).
Stopwatch mode
Standard measurement
1. Push the “RESET” button to start the stopwatch.
2. Push the “SELECT” button to stop the stopwatch.
3. Push the “SELECT” button again to reset the stopwatch.
Split-time measurement
1. Push the “RESET” button to start the stopwatch.
2. Push the “RESET” button to measure split-times. (The colon “:” will start flashing.)
3. Push the “RESET” button to display the final split-time or push the “SELECT” button to stop the stop-
watch and display total elapsed time.
4. Push the “SELECT” button to reset the stopwatch.
Coolant temperature display
The coolant temperature display indicates the temperature of the coolant. Push the “RESET” button to
switch the coolant temperature display to the air intake temperature display.
When the coolant temperature display is selected, “C” is displayed before the coolant temperature.
Air intake temperature display
The air intake temperature display indicates the temperature of the air drawn into the air filter case. Push
the “RESET” button to switch the coolant temperature display to the air intake temperature display.
Even if the air intake temperature is set to be displayed, the coolant temperature warning light comes
on when the engine overheats.
When the key is turned to “ON”, the coolant temperature is automatically displayed, even if the air
intake temperature was displayed prior to turning the key to “OFF”.
When the air intake temperature display is selected, “A” is displayed before thetemperature.
ProCarManuals.com
Page 20 of 457
1-4
FEATURES
GEN
INFO
NOTE: Self-diagnosis devices
The model is equipped with a self-diagnosis device for various electrical circuits. If any of those circuits
are defective, the engine trouble warning light will come on, and then the right display will indicate a
two-digit error code (e.g.,11,12,13).
Display brightness and shift timing indicator light control mode
This mode cycles through five control functions, allowing you to make the following settings in the order
listed below.
Display brightness:
This function allows you to adjust the brightness of the displays and tachometer to suit the outside
lighting conditions.
Shift timing indicator light activity:
This function allows you to choose whether or not the indicator light should be activated and whether
it should flash or stay on when activated.
Shift timing indicator light activation:
This function allows you to select the engine speed at which the indicator light will be activated.
Shift timing indicator light deactivation:
This function allows you to select the engine speed at which the indicator light will be deactivated.
Shift timing indicator light brightness:
This function allows you to adjust the brightness of the indicator light to suit your preference.
To make any settings in this mode, you have to cycle through all of its functions. However, if the key is
turned to “OFF” or the engine is started before completing the procedure, only the settings made be-
fore the “SELECT” button was last pushed will be applied.
In this mode, the right display shows the current setting for each function (except the shift timing indi-
cator light activity function).
To adjust the brightness of the multifunction meter displays and tachometer
1. Turn the key to “OFF”.
2. Push and hold the “SELECT” button.
3. Turn the key to “ON”, and then release the “SELECT” button after five seconds.
4. Push the “RESET” button to select the desired brightness level.
5. Push the “SELECT” button to confirm the selected brightness level. The control mode changes to
the shift timing indicator light activity function.
To set the shift timing indicator light activity function
1. Push the “RESET” button to select one of the following indicator light activity settings:
The indicator light will stay on when activated. (This setting is selected when the indicator light stays
on.)
The indicator light will flash when activated. (This setting is selected when the indicator light flashes
four times per second.)
The indicator light is deactivated; in other words, it will not come on or flash. (This setting is selected
when the indicator light flashes once every two seconds.)
2. Push the ”SELECT” button to confirm the selected indicator light activity. The control mode changes
to the shift timing indicator light activation function.
ProCarManuals.com
Page 44 of 457
2-16
ELECTRICAL SPECIFICATIONSSPEC
ItemStandardLimit
Indicator light
(voltage / wattage quantity)
Neutral indicator light
High beam indicator light
Oil level warning light
Turn signal indicator light
Fuel level warning light
Coolant temparture indicator light
Engine trouble warning light
Shift timing indicator light
LED 1
LED 1
LED 1
LED 2
LED 1
LED 1
LED 1
LED 1
Electric starting system
System type
Starter motor
Model (manufacturer)
Power output
Brushes
Overall length
Spring force
Armature coil resistance
Commutator diameter
Mica undercut
Constant mesh
5VY (YAMAHA)
0.9 kW
10.8 mm (0.43 in)
5.28 7.92 N (538 808 g,
18.99 28.48 oz)
0.0090 0.0110 Ω at 20C (68F)
24.5 mm (0.96 in)
1.5 mm (0.06 in)
3.6 mm
(0.14 in)
23.5 mm
(0.93 in)
Starter relay
Model (manufacturer)
Amperage
Coil resistance
2768079-A (JIDECO)
180 A
4.18 4.62 Ω at 20C (68F)
Horn
Horn type
Model (manufacturer) quantity
Max. amperage
Performance
Coil resistance
Plane
YF-12 (NIKKO) 1
3 A
105 113 db / 2 m
1.15 1.25 Ω at 20C (68F)
Turn signal relay
Relay type
Model (manufacturer)
Self-cancelling device built-in
Turn signal blinking frequency
Wattage
Full transistor
FE218BH (DENSO)
No
75 95 cycles / min.
21 W 2 + 3.4 W
Oil level switch
Model (manufacturer)
5VY (SOMIC ISHIKAWA)
EXUP servo motor
Model (manufacturer)
5VY (YAMAHA)
ProCarManuals.com
Page 120 of 457
3-43
ADJUSTING THE REAR BRAKE
CHK
ADJ
a
b
WARNING
WARNING
CAUTION:
EAS00110
ADJUSTING THE REAR BRAKE
1. Adjust:
brake pedal position
a. Loosen the locknut
1.
b. Turn the adjusting bolt
2 in direction a or b
until the specified brake pedal position is ob-
tained.
Direction
Brake pedal is raised.
DirectionBrake pedal is lowered.
After adjusting the brake pedal position,
check that the end of the adjusting bolt
c is
visible through the hole
d.
c. Tighten the locknut
1 to specification.
Locknut
16 Nm (1.6 mkg, 12 ftlb)
A soft or spongy feeling in the brake pedal
can indicate the presence of air in the brake
system. Before the vehicle is operated, the
air must be removed by bleeding the brake
system. Air in the brake system will consid-
erably reduce braking performance and
could result in loss of control and possibly
an accident. Therefore, check and, if neces-
sary, bleed the brake system.
After adjusting the brake pedal position,
make sure there is no brake drag.
2. Adjust:
rear brake light switch
Refer to “ADJUSTING THE REAR BRAKE
LIGHT SWITCH”.
ProCarManuals.com
Page 137 of 457
3-60
CHECKING THE TIRES / CHECKING THE WHEELS
CHK
ADJ
WARNING
NOTE:
WARNING
NOTE: Front tire
Manufacturer
SizeModel
DUNLOP120 / 70ZR 17
M / C (58W)D218FL
MICHELIN120 / 70ZR 17
M / C (58W)Pilot
POWER C
Rear tire
Manufacturer
SizeModel
DUNLOP190 / 50ZR 17
M / C (73W)D218L
MICHELIN190 / 50ZR 17
M / C (73W)Pilot
POWER G
New tires have a relatively low grip on the
road surface until they have been slightly
worn. Therefore, approximately 100 km
should be traveled at normal speed before
any high-speed riding is done.
For tires with a direction of rotation mark
1:
Install the tire with the mark pointing in the
direction of wheel rotation.
Align the mark
2 with the valve installation
point.
EAS00168
CHECKING THE WHEELS
The following procedure applies to both of the
wheels.
1. Check:
wheel
Damage / out-of-round Replace.
Never attempt to make any repairs to the
wheel.
After a tire or wheel has been changed or re-
placed, always balance the wheel.
ProCarManuals.com
Page 139 of 457
3-62
CHECKING AND CHARGING THE BATTERY
CHK
ADJ
WARNING
CAUTION:
EAS00178
ELECTRICAL SYSTEM
CHECKING AND CHARGING THE BATTERY
Batteries generate explosive hydrogen gas
and contain electrolyte which is made of poi-
sonous and highly caustic sulfuric acid.
Therefore, always follow these preventive
measures:
Wear protective eye gear when handling or
working near batteries.
Charge batteries in a well-ventilated area.
Keep batteries away from fire, sparks or
open flames (e.g., welding equipment,
lighted cigarettes).
DO NOT SMOKE when charging or han-
dling batteries.
KEEP BATTERIES AND ELECTROLYTE
OUT OF REACH OF CHILDREN.
Avoid bodily contact with electrolyte as it
can cause severe burns or permanent eye
injury.
FIRST AID IN CASE OF BODILY CONTACT:
EXTERNAL
Skin – Wash with water.
Eyes – Flush with water for 15 minutes and
get immediate medical attention.
INTERNAL
Drink large quantities of water or milk fol-
lowed with milk of magnesia, beaten egg or
vegetable oil. Get immediate medical atten-
tion.
This is a sealed battery. Never remove the
sealing caps because the balance between
cells will not be maintained and battery per-
formance will deteriorate.
Charging time, charging amperage and
charging voltage for an MF battery are dif-
ferent from those of conventional batter-
ies. The MF battery should be charged as
explained in the charging method illustra-
tions. If the battery is overcharged, the
electrolyte level will drop considerably.
Therefore, take special care when charging
the battery.
ProCarManuals.com
Page 145 of 457
3-68
CHECKING THE FUSES
CHK
ADJ
WARNING
Pocket tester
90890-03112, YU-3112
b. If the pocket tester indicates “∞”, replace the
fuse.
3. Replace:
blown fuse
a. Set the main switch to “OFF”.
b. Install a new fuse of the correct amperage
rating.
c. Set on the switches to verify if the electrical
circuit is operational.
d. If the fuse immediately blows again, check
the electrical circuit.
Fuses
Amperage
ratingQ’ty
Main50 A1
Fuel injection
system15 A1
Headlight25 A1
Signaling
system10 A1
Ignition15 A1
Backup fuse
(odometer
and clock)
10 A1
Radiator
fan motor15 A2
Reserve25 A, 15 A,
10 A1
Never use a fuse with an amperage rating
other than that specified. Improvising or us-
ing a fuse with the wrong amperage rating
may cause extensive damage to the electri-
cal system, cause the lighting and ignition
systems to malfunction and could possibly
cause a fire.
4. Install:
front cowling inner panel (left)
Refer to “COWLINGS”.
rider seat
Refer to “SEATS”.
ProCarManuals.com
Page 146 of 457
3-69
A
A
B
B
B
REPLACING THE HEADLIGHT BULBS
CHK
ADJ
WARNING
EAS00183
REPLACING THE HEADLIGHT BULBS
The following procedure applies to both of the
headlight bulbs.
1. Disconnect:
headlight bulb cover
1
headlight coupler 2
Ahigh beam
Blow beam
2. Remove:
headlight bulb holder
1
Ahigh beam
Blow beam
3. Remove:
headlight bulb
Since the headlight bulb gets extremely hot,
keep flammable products and your hands
away from the bulb until it has cooled down.
4. Install:
headlight bulb
New
Secure the new headlight bulb with the head-
light bulb holder.
ProCarManuals.com
Page 176 of 457
4-29
FRONT AND REAR BRAKESCHAS
WARNING
13 Nm (1.3 mkg, 9.4 ftlb)
NOTE:
30 Nm (3.0 mkg, 22 ftlb)
WARNING
EAS00607
ASSEMBLING AND INSTALLING THE
FRONT BRAKE MASTER CYLINDER
Before installation, all internal brake com-
ponents should be cleaned and lubricated
with clean or new brake fluid.
Never use solvents on internal brake com-
ponents.
Recommended brake fluid
DOT 4
1. Install :
brake master cylinder kit
circlip
New
dust boot
2. Install:
brake master cylinder
1
Install the brake master cylinder holder with
the “UP” mark
a facing up.
Align the end of the brake master cylinder
holder with the punch mark
b on the right han-
dlebar.
First, tighten the upper bolt, then the lower bolt.
There should be 2 2.5 mm (0.08 0.10 in)
for clearance between the right handlebar
switch and the brake master cylinder holder.
3. Install:
copper washers
New
brake hose
union bolt
brake light switch coupler
Proper brake hose routing is essential to in-
sure safe motorcycle operation. Refer to
“CABLE ROUTING”.
ProCarManuals.com