Fuel Abarth 500 2013 Owner handbook (in English)

62
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
AT THE FILLING
STATION
Use unleaded petrol only, with octane
number (R.O.N.) not lower than 95.
IMPORTANT An inefficient catalyst leads
to harmful exhaust emissions, thus con-
tributing to air pollution.
IMPORTANT Never use leaded petrol,
even in small amount or in an emergency,
as this would damage the catalyst beyond
repair.
REFILLING
To ensure full fuel tank refilling, perform
two topping up after the first stop of the
nozzle. Do not top up further; this may
cause anomalies in the fuel supply system.
FUEL FILLER CAP fig. 60
The cap Bis provided with a loss pre-
vention device Cwhich secures it to the
lid A.
Unscrew cap Busing the ignition key. The
airtight closing may determine a slight in-
crease of pressure in the tank. A suction
noise when you release the cap is there-
fore entirely normal. When refuelling, fas-
ten the cap to the device inside the lid as
shown in figure.Do not approach naked
flames or lit cigarettes to the
fuel filler: fire risk. Keep your
face away from the fuel filler
to prevent breathing in harmful vapours.
fig. 60F0S059Ab
PROTECTING THE
ENVIRONMENT
The devices for curtailing petrol engine
emissions are the following:
❒three-way catalytic converter;
❒Lambda sensors;
❒fuel evaporation prevention system.
In addition, do not let the engine run, even
for a test, with one or more spark plugs
disconnected.
The catalytic converter de-
velops high temperature dur-
ing operation. Do not park on grass,
dry leaves, pine needles or other flam-
mable material: fire risk .
WARNING
046-062 ABARTH 500 1ed GB:046-064 ABARTH 500 GB 24-05-2012 9:51 Pagina 62

80
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE CAR
STARTING PROCEDURE FOR
PETROL VERSIONS
Proceed as follows:
❒ensure that the handbrake is up;
❒put the gear lever into neutral;
❒press the clutch pedal down to the
floor without touching the accelerator;
❒turn the ignition key to AVVand let
it go the moment the engine starts.
If the engine does not start at the first at-
tempt, return the ignition key to STOP
before repeating starting.
If, when the ignition key is at MAR, war-
ning light
Yremains lit together with
warning light Uturn the key to STOP
and then back to MAR; if the warning li-
ght remains on, try with the other keys
provided with the car.
If you still do not manage to start the en-
gine, go to an Abarth Dealership.
STARTING THE
ENGINE
The car is provided with an electronic en-
gine lock device: refer to “The Fiat CO-
DE system” paragraph in “Your car” if you
cannot start the engine.
The engine may be noisier during the first
seconds of operation, particularly after a
long period of inactivity. This does not im-
pair functionality and reliability and is typ-
ical of hydraulic tappets: the distribution
system selected for the petrol engines of
your car in order to limit the maintenance
required.
In the first period of use, we
recommend to avoid excessi-
ve stress for the car (for in-
stance excessive accelera-
tions, extended travel at maximum
speed, sudden braking etc.).
With engine off, do not leave
the key in the ignition switch
on MAR to prevent draining
the battery.
It is dangerous to have the
engine running in closed en-
vironments. The engine depletes the
oxygen and discharges carbon dioxi-
de, carbon monoxide and other toxic
gases.
WARNING
Remember that the servo-
brake and electric power
steering are not operational until the
engine has been started, therefore
more effort than usual is required on
the brake pedal and steering wheel.
WARNING
Never jump start the engine
by pushing, towing or driving
downhill. This could cause a
flow of fuel into the catalytic
converter and damage it beyond re-
pair.
079-086 ABARTH 500 1ed GB:079-086 ABARTH 500 GBdx 24-05-2012 9:55 Pagina 80

81
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE CAR
HANDBRAKE
The handbrake lever is located between
the two front seats.
Pull the lever upwards to operate the
handbrake.
PARKING THE CAR
Proceed as follows:
❒stop the engine and engage the hand-
brake;
❒engage a gear (on a slope, engage first
gear if the car is faced uphill or rever-
se if it is faced downhill) and leave the
wheels steered.
If the car is parked on a steep slope, it is
further advisable to block the wheels with
a wedge or stone.
Do not leave the ignition key on MARto
prevent draining the battery. Always re-
move the key when you leave the car.
Never leave children unattended in the
car. Always remove the ignition key when
leaving the car and take it out with you. HOW TO WARM UP THE
ENGINE AFTER IT HAS JUST
STARTED
Proceed as follows:
❒drive off slowly, letting the engine turn
at medium speed. Do not accelerate
abruptly;
❒do not demand maximum performan-
ce for the first few kilometres. Wait un-
til the engine coolant temperature gau-
ge starts moving.
STOPPING THE ENGINE
Turn the ignition to STOPwhile the en-
gine is idling.
IMPORTANT After a taxing drive, you
should allow the engine to “catch its
breath” before turning it off by letting it
idle to allow the temperature in the engi-
ne compartment to fall.
A quick burst on the accele-
rator before turning off the
engine serves absolutely no
practical purpose, it wastes
fuel and is damaging especially to tur-
bocharged engines.The car must be braked after
a few snaps of the lever,
otherwise, contact the Abarth Dea-
lership for regulation.
WARNING
When the handbrake lever is pulled up
and the ignition key is on MAR, the in-
strument panel warning light
xwill turn
on.
Proceed as follows to release the hand-
brake:
❒slightly lift the handbrake and press re-
lease button A-fig. 1;
❒hold button Apressed and lower the
lever. Warning light xon the instru-
ment panel will go out.
Press the brake pedal when carrying out
this operation to prevent the car from
moving accidentally.
fig. 1F0S076Ab
079-086 ABARTH 500 1ed GB:079-086 ABARTH 500 GBdx 24-05-2012 9:55 Pagina 81

82
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE CAR
CONTAINING
RUNNING COSTS
Here are some useful tips to save fuel and
minimize polluting emissions of CO
2and
other pollutants (nitric oxide, unburnt hy-
drocarbons, fine dusts etc…).
GENERAL CONSIDERATIONS
Car maintenance
Have checks and adjustments carried out
in accordance with the “Service schedule”.
Tyres
Check tyre pressure regularly at least on-
ce every four weeks: excessively low pres-
sure will increase consumption because
rolling resistance will be higher.
Unnecessary loads
Do not travel with an overloaded boot.
Do not travel with too much luggage
stowed in the boot. The weight of the car
(especially when driving in town) and its
trim greatly affect consumption and stabi-
lity.
USING THE MANUAL
GEARBOX
To engage the gears, press the clutch pe-
dal fully and shift the gear lever into one
of the required positions (the diagram is
shown on the knob fig. 2).
IMPORTANT Reverse may only be enga-
ged when the car is at a standstill. With
the engine running, wait for at least 2 se-
conds with the clutch pedal fully pressed
before engaging reverse to prevent da-
mage to the gears and grating.
In addition, to assist the transmission of the
drive torque, a limit on the engine revs du-
ring take off at 2700 rpm can be noticed.
When the clutch pedal is released and the
vehicle is being driven, the engine revs re-
striction is disabled.
To engage reverse gear Rfrom neutral,
move the lever to the right and then
backwards.
IMPORTANT The clutch pedal must be
used for gear shift only. Never drive with
the foot resting, even if slightly, on the
clutch pedal. For versions/markets, whe-
re provided, the clutch pedal control elec-
tronics can intervene interpreting the
wrong drive style as a faultPress the clutch pedal fully to
change gears correctly. For
this reason, there must be no
obstacles on the floor under
the pedals: ensure that rubber mats (if
any) are correctly positioned, not in-
terfering with the pedals.
Do not drive with the hand
resting on the gear lever, be-
cause this pressure, even if light, over
time can wear gear inner compo-
nents.
WARNING
fig. 2F0S077Ab
079-086 ABARTH 500 1ed GB:079-086 ABARTH 500 GBdx 24-05-2012 9:55 Pagina 82

83
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE CAR
Accessories fitted on
longitudinal bars
If not used, remove from the roof acces-
sories such as: longitudinal bars, ski rack,
luggage rack, etc. These accessories de-
crease aerodynamic penetration of the car
and have a negative effect on consumption.
It is better to use a trailer to transport
particularly bulky objects.
Electric devices
Use electric devices only for the amount
of time needed. Rear heated window, ad-
ditional headlights, windscreen wipers and
heater fan need a considerable amount of
energy, therefore increasing the require-
ment of current increases fuel consump-
tion (up to +25% in the urban cycle).Climate control
The climate control system leads to higher
fuel consumption (up to +20% on avera-
ge): use air vents only when the external
temperature allows to.
Spoilers
The use of non-certified aerodynamic
items may adversely affect air drag and
consumption levels.DRIVING STYLE
Starting
Do not warm the engine up with the car
standing: the engine warms up very slowly
in these conditions, increasing consump-
tion and emissions. It is advisable to start
off immediately and slowly keeping the en-
gine speed down: the engine will warm up
much faster this way.
Unnecessary actions
Avoid revving up when starting at traffic
lights or before stopping the engine. The
latter action, like doubling the clutch, is un-
necessary and causes increase of con-
sumption and pollution.
Gear selection
Use a higher gear as soon as traffic and
road conditions allow. Using a low gear
for faster acceleration will increase con-
sumption.
In the same way improper use of a high
gear increases consumption, emissions an
engine wear.
079-086 ABARTH 500 1ed GB:079-086 ABARTH 500 GBdx 24-05-2012 9:55 Pagina 83

84
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE CAR
CONDITIONS OF USE
Cold starting
Short distances and frequent cold start-ups
will prevent the engine from reaching op-
timal running temperature. Consequently,
both consumption (from +15 to +30% on
urban cycle ) and emissions will increase.
Traffic and road conditions
Rather high consumption is caused by
heavy traffic, for instance when travelling
in a queue with frequent use of low gears
or in cities with many traffic lights. Moun-
tain and rough roads also have a negative
effect on consumption.
Traffic hold-ups
During prolonged hold-ups (level crossings)
the engine should be switched off.SNOW TYRES
Use snow tyres of the same size as the
normal tyres provided with the car.
Abarth Dealership will be happy to pro-
vide advice concerning the most suitable
type of tyre for the customer’s require-
ments.
For the type of tyre to be used, inflation
pressures and the specifications of snow
tyres, follow the instructions given in pa-
ragraph “Wheels” in section “Technical
specifications”.
The performance of these tyres is consi-
derably reduced when the tread thickness
is less than 4 mm. Replace them in this ca-
se.
Due to their specific features, the perfor-
mance of snow tyres is much lower than
that of normal types in normal conditions
or long motorway stretches. Limit perfor-
mance according to the use for which they
were approved. Top speed
Fuel consumption considerably increases
as speed increases. Keep your speed as
even as possible, avoiding unnecessary
braking and acceleration which cause ex-
cessive fuel consumption and increase
emissions.
Acceleration
Sudden acceleration has a very negative
effect on consumptions and emissions: ac-
celerate gradually.
079-086 ABARTH 500 1ed GB:079-086 ABARTH 500 GBdx 24-05-2012 9:55 Pagina 84

87
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
GENERAL WARNINGS ..................................................... 88
LOW BRAKE FLUID............................................................ 88
HANDBRAKE ON................................................................ 88
AIR BAG FAILURE ................................................................88
FRONT PASSENGER AIRBAG DEACTIVATED ........... 89
HOT ENGINE COOLANT................................................ 89
LOW BATTERY CHARGE ................................................. 90
ABS SYSTEM FAILURE......................................................... 90
EBD SYSTEM FAILURE ........................................................90
LOW ENGINE OIL PRESSURE.......................................... 90
“DUALDRIVE” ELECTRIC POWER
STEERING FAILURE ............................................................ 91
INCOMPLETE DOOR LOCKING .................................... 91
ENGINE EOBD / INJECTION
CONTROL SYSTEM FAILURE ......................................... 91
FUEL RESERVE ....................................................................... 92
FIAT CODE PROTECTION
SYSTEM FAILURE..................................................................92
REAR FOG LIGHTS.............................................................. 92
GENERIC FAILURE INDICATION ................................. 93
ENGINE OIL PRESSURE SENSOR FAILURE .................. 93
FUEL CUT-OFF INERTIAL SWITCH
INTERVENTION ...................................................................93
EXTERNAL LIGHTS FAILURE .......................................... 93ESP SYSTEM FAILURE ........................................................ 93
HILL HOLDER FAILURE .................................................... 93
SIDELIGHTS AND LOW BEAMS..................................... 93
FOLLOW ME HOME ........................................................... 93
FRONT FOG LIGHTS ........................................................ 94
LEFT-HAND DIRECTION INDICATOR ........................ 94
RIGHT-HAND DIRECTION INDICATOR.................... 94
SPORT FUNCTION ACTIVATION.................................94
MAIN BEAM HEADLIGHTS............................................... 94
POSSIBLE ICE ON THE ROAD.........................................94
SPEED LIMIT EXCEEDED .................................................. 94
LIMITED RANGE ................................................................. 94
BRAKE PAD WEAR ............................................................ 94
SEAT BELTS NOT FASTENED .......................................... 94
W W
A A
R R
N N
I I
N N
G G

L L
I I
G G
H H
T T
S S

A A
N N
D D

M M
E E
S S
S S
A A
G G
E E
S S
087-094 ABARTH 500 1ed GB:087-094 ABARTH 500 GB 24-05-2012 9:53 Pagina 87

92
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
Go to a Abarth Dealership as
soon as possible if warning
light
Udoes not light up
when the key is turned to
MAR or if, while travelling, the warn-
ing light comes on either steady or
blinking (along with a message on the
display). The operation of warning light
Umay be checked by the traffic po-
lice using specific devices. Follow the
laws in force in the country where you
are driving.
K
FUEL RESERVE
(amber)
Turning the ignition key to
MARthe warning light turns on, but it
should go off after a few seconds.
The warning light turns on when about 5
litres of fuel are left in the tank.
IMPORTANT The warning light will blink
to indicate a system failure. Go to a Abarth
Dealership to have the system checked.
CAR PROTECTION
SYSTEM FAILURE -
FIAT CODE (amber)
If with the ignition key at MAR, the warn-
ing light stays on, this indicates a possible
failure (see “Fiat Code system” in section
“Your car”).
IMPORTANT Warning lights
Uand Ywill come on at the same time to indicate
a Fiat CODE system failure.
If with the engine running the warning light
Yflashes, this means that the car is not
protected by the engine inhibitor device
(see “Fiat Code system” in section “Your
car”).
Contact Abarth Dealership to have all the
key stored.
Y
REAR FOG LIGHTS
(amber)
The warning light comes on
when the rear fog lights are turned on.
4
GENERIC FAILURE
INDICATION
(amber)
The warning light turns on in the follow-
ing circumstances.
Engine oil pressure
sensor failure
The warning light turns on when failure
is detected in parking sensors. Go to a
Abarth Dealership to have the fault fixed
as soon as possible.
Parking sensor failure
The warning light turns on and the mes-
sage is shown on the display when a park-
ing sensor fault is detected. Contact a
Abarth Dealership.
è
If the light flashes, release the accelerator
pedal to lower the speed of the engine un-
til the warning light stops flashing; contin-
ue the journey at moderate speed, trying
to avoid driving conditions that may cause
further flashing and contact Abarth Deal-
ership as soon as possible.
087-094 ABARTH 500 1ed GB:087-094 ABARTH 500 GB 24-05-2012 9:53 Pagina 92

SIDE/TAILLIGHTS
AND LOW BEAMS
(green)
FOLLOW ME HOME
(green)
Side/taillights and low beams
The warning light turns on when
side/taillights or low beams are turned on.
Follow me home
The warning light will turn on when this
device is active (see “Follow me home”
in section “Your car”).
The display will show the dedicated mes-
sage.
93
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
Fuel cut-off inertial switch
intervention/fuel cut-off not
available
The warning light turns on when the fu-
el cut-off inertial switch intervenes or
when the fuel cut-off system is not avail-
able.
The display will show the dedicated mes-
sage.
External lights failure
The warning light comes on when an ex-
ternal light failure is detected.ESP SYSTEM FAILURE/
HILL HOLDER FAILURE
(amber)
ESP system failure
Turning the ignition key to MARthe
warning light turns on, but it should go off
after a few seconds.
If the warning light does not go out or re-
mains on whilst driving, go to an Abarth
Dealership.
The display will show the dedicated mes-
sage.
NoteWarning light flashing when driving
indicates that the ESP system is active.
Hill Holder failure
Turning the ignition key to MARthe
warning light turns on, but it should go off
after a few seconds.
The warning light turns on to indicate a
Hill holder system failure. In this case, con-
tact Abarth Dealership as soon as possi-
ble.
The display will show the dedicated mes-
sage.
3á
087-094 ABARTH 500 1ed GB:087-094 ABARTH 500 GB 24-05-2012 9:53 Pagina 93

97
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
IN AN
EMERGENCY
Proceed as follows:
❒Connect positive terminals (+ sign near
the terminal) of the two batteries with
a jump lead;
❒With a second lead, connect the nega-
tive terminal (–) of the auxiliary battery
to an earthing point
Eon the engine or
the gearbox of the car to be started;
❒Start the engine;
❒When the engine has been started, re-
move the leads reversing the order
above.If after a few attempts the engine does not
start, do not insist any further but contact
the nearest Abarth Dealership.
IMPORTANT Never connect the negative
terminals of the two batteries directly:
sparks could ignite explosive gas released
from the battery. If the auxiliary battery is
installed on another car, prevent acciden-
tal contact between metallic parts of the
two cars.BUMP STARTING
Never jump start the engine by pushing,
towing or driving downhill.
This could cause a flow of fuel into the cat-
alytic converter and damage it beyond re-
pair.
IMPORTANT Remember that the brake
booster and the power steering system
are not operating until the engine is start-
ed, a greater effort will therefore be re-
quired to press the brake pedal or turn
the steering wheel.
095-122 ABARTH 500 1ed GB:095-122 ABARTH 500 GB 24-05-2012 9:56 Pagina 97