Battery ACURA CSX 2006 Service Repair Manual



13-98Manual Transmission
Transmission Installation (cont’d)
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
(P/N 08798-9002) B
A
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) 6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) B
A
C
C
D
40. Apply super high temp urea grease (P/N 08798-
9002) to the end of the slave cylinder pushrod.
Install the slave cylinder (A), then install the clutch
line bracket (B). Be careful not to bend the clutch
line.
41. Install the battery base (A) with the coolant reservoir (B). 42. Install the harness clips (C) and the intake air duct
(D).
43. Install the air cleaner assembly (see page 11-345).
44. Do the battery installation procedure (see page 22-69).
45. Install the under-cowl panel and the cowl cover (see page 20-163).
46. Check the shift lever and the clutch operation.
47. Check the wheel alignment (see page 18-5).
48. Test-drive the vehicle.
08/08/21 14:47:31 61SNR030_130_0100
ProCarManuals.com
DYNOMITE -2009-

Î
ØÚÓ´
µ
Electronic Control System (cont’d)
PCM A/T Control System Electrical Connections
14-48 Automatic Transmission
System Description (cont’d)
41
23
41 24
23 4
40
29
26 2
27
20 21
10
89
35 19
16 17 18
36 39 40 44434230
29 32 16 1817
13 14 15
1211 789
654321
31
36 37 4044
42
27 28 29
33 3424 25
20 21 14 15
654
31 23
31
13
9
87
11 12 1514 13 17 18
16
22
21
20 25
32 35 34
33
3028
27
42 43 44
36 22
39
10
26
SHE
B24
RIGHT SUPP
B16
B40
SDNP
LEFT
F-CAN Transceiver
CANL
A37
CANH
A36
Terminal side of female terminals
A (44P) B (44P) C (44P) C44 C40 B1 B36
B15
ATPS
S
Dash-light Brightness Control Circuit
SG1C14
NC C43
VCC1 C13
B33
SG2 B17
NM B18
VCC2
TATF B27 B11
SHB SHA B10
B20
SHC
B26
SHD LSC
B25 B35
LSB
PG1
B28
ATPFWD
N BAT
D
PG2
ATPP
B13
DATA LINK CONNECTOR
R
CPU
LG1
ATPR
B14 SCS
IGNITION SWITCH
LG2
GAUGE CONTROL MODULE (TACH)
B9OP3SW OP2SW
B8 ATPRVS
B22 ATPD
B12
P
S
R
P
ND B21ATPN
BKSW
A40
BRAKE LIGHTS A31 A27SLS PCM
C36 IG1 B44
LSA
BATTERY
IG1
BRAKE PEDAL
POSITION SWITCH SHIFT LOCK
SOLENOID
TRANSMISSION
RANGE SWITCH A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE A
A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE B
A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE C
SHIFT SOLENOID
VALVE A
SHIFT SOLENOID
VALVE B
SHIFT SOLENOID
VALVE C
SHIFT SOLENOID
VALVE D
ATF
TEMPERATURE
SENSOR
OUTPUT SHAFT
(COUNTERSHAFT)
SPEED
SENSOR
INPUT SHAFT
(MAINSHAFT)
SPEED
SENSOR
2ND CLUTCH TRANSMISSION
FLUID PRESSURE SWITCH
3RD CLUTCH TRANSMISSION
FLUID PRESSURE SWITCH
A/T Gear Position Indicator
Driver Circuit
SHIFT
INDICATOR SHIFT SOLENOID
VALVE E
PADDLE SHIFTER (UPSHIFT SWITCH)
PADDLE SHIFTER (DOWNSHIFT SWITCH)
PCM Connector Terminal Locations
08/08/21 14:38:25 61SNR030_140_0050
ProCarManuals.com
DYNOMITE -2009-

Î
ØÚ Ó
Ø
Ú
PCM A/T Control System Inputs and Outputs
PCM CONNECTOR A (44P) Wire Color Terminal Name Description Signal
PCM CONNECTOR B (44P) Wire Color Terminal Name Description SignalTerminalNumber
Terminal Number
14-49
A (44P) B (44P) C (44P)
PCM Connector Terminal Locations
A27 PNK SLS (SHIFT LOCK
SOLENOID) Drives shift lock solenoid With ignition switch ON (II), in P, brake pedal
pressed, and accelerator released: about battery
voltage
A31 BRN SCS (SERVICE CHECK SIGNAL) Detects service check signal With service check signal shorted using HDS: about
0V
With service check signal opened: about 5.0 V
A36 WHT CANH (CAN COMMUNICATION SIGNAL
HIGH) Sends and receives
communication signal
With ignition switch ON (II): about 2.5 V (pulses)
A37 RED CANL (CAN COMMUNICATION SIGNAL
LOW) Sends and receives
communication signal
With ignition switch ON (II): about 2.5 V (pulses)
A40 LT GRN BKSW (BRAKE PEDAL POSITION SWITCH) Detects brake pedal
position switch signalWith brake pedal pressed: about battery voltage
With Brake pedal released: about 0 V
NOTE: Standard battery voltage is about 12 V.


B1 BLK/RED
BLKPG2 (POWER GROUND) Ground circuit for PCM
circuitLess than 1.0 V at all times
B8 BLU/RED OP2SW (2ND CLUTCH TRANSMISSION FLUID
PRESSURE SWITCH) Detects 2nd clutch
transmission fluid pressure
switch signalWith ignition switch ON (II):
Without 2nd clutch pressure: about 5.0 V
With 2nd clutch pressure: about 0 V
NOTE: Standard battery voltage is about 12 V.
*1: ’06 model
*2: ’07-09 models
(cont’d)
*1
*2
Terminal side of female terminals
08/08/21 14:38:26 61SNR030_140_0051
ProCarManuals.com
DYNOMITE -2009-

´´´
´
Î
ØÚ Ó
Ú
Electronic Control System (cont’d)
PCM A/T Control System Inputs and Outputs (cont’d)
PCM CONNECTOR B (44P)Wire Color Terminal Name Description SignalTerminalNumber
14-50Automatic Transmission
System Description (cont’d)
A (44P)
B (44P) C (44P)
PCM Connector Terminal Locations




B9 BLU/WHT OP3SW (3RD CLUTCH
TRANSMISSION FLUID
PRESSURE SWITCH) Detects 3rd clutch
transmission fluid pressure
switch signalWith ignition switch ON (II):
Without 3rd clutch pressure: about 5.0 V
With 3rd clutch pressure: about 0 V
B10 BLU/BLK SHA (SHIFT SOLENOID VALVE A) Drives shift solenoid
valve AWith engine running in R, D and S (in 1st, 4th, and
5th gears): about battery voltage
With engine running in P, N, D and S (in 2nd and 3rd
gears): about 0 V
B11 GRN/WHT SHB (SHIFT SOLENOID VALVE B) Drives shift solenoid
valve BWith engine running in P, R, N, D and S (in 1st and
2nd gears): about battery voltage
With engine running in D and S (in 3rd, 4th, and 5th
gears): about 0 V
B12 RED/BLK ATPN (TRANSMISSION RANGE SWITCH NEUTRAL) Detects transmission range
switch N position signalIn N: about 0 V
In any position other than N: more than 5.0 V
B13 BLU/BLK ATPP (TRANSMISSION RANGE SWITCH PARK) Detects transmission range
switch P position signalIn P: about 0 V
In any position other than P: more than 5.0 V
B14 WHT ATPR (TRANSMISSION RANGE SWITCH R) Detects transmission range
switch R position signalIn R: about 0 V
In any position other than R: more than 5.0 V
B15 RED ATPS (TRANSMISSION RANGE SWITCH S) Detects transmission range
switch S position signalIn S: about 0 V
In any position other than S: about battery voltage
B16 BLU/YEL SUPP (PADDLE SHIFTER (UPSHIFT SWITCH)) Detects paddle shifter
(upshift switch) signalIn S:
With paddle shifter (upshift switch) pressed:
about 0 V
With paddle shifter (upshift switch) released:
about battery voltage
B17 WHT/RED NM (INPUT SHAFT (MAINSHAFT) SPEED
SENSOR) Detects input shaft
(mainshaft) speed sensor
signalWith ignition switch ON (II): about 0 V
With engine idling in N: about 2.5 V
B18 YEL/BLU VCC2 (SENSOR VOLTAGE) Provides sensor reference voltageWith ignition switch ON (II): about 5.0 V
B20 GRN SHC (SHIFT SOLENOID VALVE C) Drives shift solenoid
valve CWith engine running in N, D and S (in 1st, 3rd, and
5th gears): about battery voltage
With engine running in P, R, D and S (in 2nd and 4th
gears): about 0 V
NOTE: Standard battery voltage is about 12 V.
Terminal side of female terminals
08/08/21 14:38:26 61SNR030_140_0052
ProCarManuals.com
DYNOMITE -2009-

µ
Ú
PCM CONNECTOR B (44P)
Wire Color Terminal Name Description Signal
TerminalNumber
14-51
B21 YEL/GRN ATPD (TRANSMISSION RANGE SWITCH D) Detects transmission range
switch D position signalIn D: about 0 V
In any position other than D: about battery voltage
B22 RED/WHT ATPRVS (TRANSMISSION RANGE SWITCH RVS) Detects transmission range
switch R position signalIn R: about 0 V
In any position other than R: about battery voltage
B24 YEL SHE (SHIFT SOLENOID VALVE E) Drives shift solenoid valve E With engine running in P and R: about battery
voltage
With engine running in N, D and S (in 1st gear):
about 0 V
B25 BLU/YEL LSC (A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE C) Drives A/T clutch pressure
control solenoid valve C
With ignition switch ON (II): current controlled
B26 GRN/RED SHD (SHIFT SOLENOID VALVE D) Drives shift solenoid
valve DWith engine running in D and S (in 2nd and 5th
gears): about battery voltage
With engine running in P, R, N, D and S (in 1st, 3rd,
and 4th gears): about 0 V
B27 RED/YEL ATFT (ATF TEMPERATURE SENSOR) Detects ATF temperature
sensor signalWith igniting switch ON (II): about 0.2 4.8 V
depending on ATF temperature
(about 1.8 V at operating temperature)
B28 BLU/YEL ATPFWD (TRANSMISSION RANGE SWITCH FWD) Detects transmission range
switch D and S positions
signalIn D and S: about 0 V
In any position other than D and S: about battery
voltage
B33 GRN/BLK SG2 (SENSOR GROUND) Sensor ground Less than 1.0 V at all times
NOTE: Standard battery voltage is about 12 V.
(cont’d)
08/08/21 14:38:26 61SNR030_140_0053
ProCarManuals.com
DYNOMITE -2009-

µµµ
µ
Î
ØÚ Ó
Ú
Ó
Electronic Control System (cont’d)
PCM A/T Control System Inputs and Outputs (cont’d)
PCM CONNECTOR B (44P)Wire Color Terminal Name Description Signal
PCM CONNECTOR C (44P) Wire Color Terminal Name Description SignalTerminalNumber
Terminal Number
14-52Automatic Transmission
System Description (cont’d)
A (44P)
B (44P) C (44P)
PCM Connector Terminal Locations


B35 BRN LSB (A/T CLUTCH
PRESSURE CONTROL
SOLENOID VALVE B) Drives A/T clutch pressure
control solenoid valve B
With ignition switch ON (II): current controlled
B36 BLK PG1 (POWER GROUND) Ground circuit for PCM circuitLess than 1.0 V at all times
B40 BRN SDNP (PADDLE SHIFTER (DOWNSHIFT SWITCH)) Detects paddle shifter
(downshift switch) signalIn S:
With paddle shifter (downshift switch) pressed:
about 0 V
With paddle shifter (downshift switch)
released: about 5.0 V
B44 RED/BLK LSA (A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE A) Drives A/T clutch pressure
control solenoid valve A
With ignition switch ON (II): current controlled
NOTE: Standard battery voltage is about 12 V.
C13 YEL/RED VCC1 (SENSOR VOLTAGE) Provides sensor reference voltageWith ignition switch ON (II): about 5.0 V
C14 GRN/WHT SG1 (SENSOR GROUND) Sensor ground Less than 1.0 V at all times
C36 BLK/GRN IG1 (IGNITION SIGNAL) Detects ignition signal With ignition switch ON (II): about battery voltage
C40 BRN/YEL LG1 (LOGIC GROUND) Ground circuit for PCM circuitLess than 1.0 V at all times
C43 BLK/WHT NC (OUTPUT SHAFT (COUNTERSHAFT) SPEED
SENSOR) Detects output shaft
(countershaft) speed sensor
signalWith ignition switch ON (II): pulses
With vehicle moving: about 5.0 V (pulses)
C44 BRN/YEL LG2 (LOGIC GROUND) Ground circuit for PCM circuitLess than 1.0 V at all times
NOTE: Standard battery voltage is about 12 V.
Terminal side of female terminals
08/08/21 14:38:27 61SNR030_140_0054
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
Ó
Ú
Ø µ
µ ´
Circuit Diagram - PCM A/T Control System
14-78Automatic Transmission
System Description (cont’d)
LT GRN
BRN
SDNP B40
GRN
BLU/YEL BLU
CABLE REEL
2
1 1 2
B16
SUPP
LG2 LG1 PG2
PG1
C40 B1
C44 B36
BLK
BRN/YEL
BRN/YEL
G101 PG SG
16
15
BLK
C(44P)
B(44P)
A(44P)
Terminal side of female terminals
19 1
WHT
RED RED
WHT
17
CANL
A37 A36 CANH
PNK 1
3827
65410 17
6
54938 10
BLK
B13 BLK/GRN BRN
C36
IG1
12 V
GAUGE CONTROL MODULE (TACH) No. 2 (15 A)
UNDER-DASH FUSE/RELAY BOX
No.10(7.5A)
BLU/WHT
RED/BLK
WHT ORN
A40
LT GRN
WHT SLS
A27
RED
BLK BAT
IG1
IGNITION SWITCH
No. 12 (15 A)
BKSW BLK
BLU/WHT
FWD RVS
S ST
P R
N
TRANSMISSION RANGE SWITCH D
B22
ATPRVS
ATPFWD
ATPP
ATPR ATPN ATPD ATPS
YEL/RED
B28
G101
B12
B21
BLU
PNK
RED/BLK
WHT
BLK/BLU
B14 B15
WHT/RED
BLU/BLK YEL/GRN
RED
BLU/YEL
1
2 YEL BLK
G503
PNK D N
R
P
UNDER-HOOD FUSE/RELAY BOX
No. 2 (IG) (50 A)
No. 1 (100 A)
BATTERY
A/T
GEAR
POSITION
INDICATOR
DRIVER
CIRCUIT
CPU STARTER
CUT RELAY
SHIFT LOCK
SOLENOID BRAKE PEDAL
POSITION SWITCH MULTIPLEX INTEGRATED
CONTROL UNIT (MICU)
F-CAN
TRANSCEIVER
DASH-LIGHT BRIGHTNESS
CONTROL CIRCUIT
RIGHT
GRN/ORN
LT GRN
BLK/WHT
LEFT
LT GRN
SHIFT
INDICATOR
RED/WHT
G504 G504
POWERTRAIN CONTROL
MODULE (PCM)
BLK/RED* BLK* *1: ’06 model
*2: ’07 09 models
5V
BLK16
17
6 16
17
7
PADDLE SHIFTER
(DOWNSHIFT SWITCH)PADDLE SHIFTER
(UPSHIFT SW ITCH)
PCM Connector Terminal Locations
S
BRN
WHT
YEL
GND
364144
43
42
27 28
30 33 34 35
32 25
20 21 22 16 18
17
13 14 15
12
11 789
43
1
3123
31
456
15
14
21
20 2524
3433
29
28
27
42 44
40
37
36 31
1
23456 9 87
11 12 1514 13 17 18
16
32
29
30
42 43 44
4039
36
181716 19
3598
10 21
20
27
2
26 29 22
40
23
24
4123
10
26 39
12
08/08/21 14:39:46 61SNR030_140_0080
ProCarManuals.com
DYNOMITE -2009-

µ

(#'

)
14-208Automatic Transmission
Road Test
A
1. Apply the parking brake, and block both rear
wheels.
2. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
3. Shift to D while pressing the brake pedal. Press the accelerator pedal, and release it suddenly. The
engine should not stall.
4. Repeat step 3 in all shift lever positions.
5. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
6. Turn the ignition switch to ON (II), and go to the A/T Data List. Make sure the HDS communicates with
the PCM. If it does not, go to the DLC circuit
troubleshooting (see page 11- 204).7. Prepare the HDS to take a HIGH SPEED SNAPSHOT
(refer to the HDS user guide for more details if
needed):
 Select High Speed icon.
 Select these parameters: – Vehicle Speed
– Output Shaft (Countershaft) Speed (rpm)
– Input Shaft (Mainshaft) Speed (rpm)
– Engine Speed
– APP Sensor A (V)
– ATF Temp Sensor (V)
– Battery Voltage
– Shift Control
– Brake Switch
 Set the Trigger Type to Parameter.
 Adjust the Parameter setting to APP Sensor A above 1.2 V.
 Set the recording time to 60 seconds.
 Set the Trigger point to 30 seconds.
8. Find a suitable level road. When you are ready to do the test, press OK on the HDS.
9. Monitor the HDS and accelerate quickly until the APP Sensor A reads 1.3 V. Maintain a steady
throttle until the transmission shifts to 5th gear,
then slow the vehicle and come to a stop.
10. Save the snapshot if the entire event was recorded or increase the recording time setting as necessary
and repeat step 9.
11. Adjust the Parameter setting to 2.4 V. Retest-drive the vehicle. While monitoring the HDS, accelerate
quickly until the APP Sensor A reads 2.5 V.
Maintain a steady throttle until the transmission
shifts to 5th gear (or reasonable speed), then slow
the vehicle and come to a stop.
12. Save the snapshot if the entire event was recorded or increase the recording time setting as necessary
and repeat step 11.
13. Accelerate quickly until the accelerator pedal is to the floor. Maintain a steady pedal until the
transmission shifts to 3rd gear, then slow to a stop,
and save the snapshot.
08/08/21 14:45:32 61SNR030_140_0210
ProCarManuals.com
DYNOMITE -2009-


Î
Î
(#'



)
14-215
Shift Solenoid Valve Test
A A
18x1.5mm
49 N·m
(5.0 kgf·m, 36 lbf·ft) B
A
B
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
C
1. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
2. Turn the ignition switch to ON (II). Make sure the HDS communicates with the PCM. If it does not, go
to the DLC circuit troubleshooting (see page
11-204).
3. Select Shift Solenoid Valves A, B, C, D, and E Test in the Miscellaneous Test Menu with the HDS.
4. Check that shift solenoid valves A, B, C, D, and E operate with the HDS. A clicking sound should be
heard.
 If a clicking sound is heard, the valves are OK. The test is complete, disconnect the HDS.
 If no clicking sound is heard, go to step 5, and test the solenoid valve.
5. Do the battery removal procedure (see page 22-69).
6. Remove the intake air duct (see page 11-348) and the air cleaner assembly (see page 11-345).
7. Remove the battery tray, the battery base, and the resonator.
8. Raise the vehicle on a lift, or apply the parking brake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
9. Remove the splash shield. 10. Remove the drain plug (A), and drain the automatic
transmission fluid (ATF).
11. Reinstall the drain plug with a new sealing washer (B).
12. Remove the shift solenoid valve cover (A), the dowel pins (B), and the gasket (C).
(cont’d)
Replace.
Replace.
08/08/21 14:46:44 61SNR030_140_0217
ProCarManuals.com
DYNOMITE -2009-

µ
Standard: 12 25
14-216Automatic Transmission
Shift Solenoid Valve Test (cont’d)
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
13. Disconnect the shift solenoid wire harness
connector, and remove it from the transmission
housing.
14. Measure the shift solenoid valve resistance between the following shift solenoid wire harness
connector terminals and body ground:
 No. 1 (GRN): Shift solenoid valve C
 No. 2 (ORN): Shift solenoid valve B
 No. 3 (RED): Shift solenoid valve E
 No. 5 (BLU): Shift solenoid valve A
 No. 8 (YEL): Shift solenoid valve D
15. If the resistance is within the standard, go to step 17 and check the solenoid valve for a clicking
sound. If the resistance is out of standard, go to
step 16.
16. Disconnect the shift solenoid valve connector, and measure the resistance at the solenoid valve
connector. Replace the shift solenoid valve if the
resistance is out of standard, then go to step 20.
17. Connect a jumper wire from the battery positive terminal to the shift solenoid wire harness
connector terminals, and connect another jumper
wire from the battery negative terminal to body
ground individually. A clicking sound should be
heard.
 If a clicking sound is heard, the valves are OK, and the test is complete, connect the connector.
 If no clicking sound is heard, replace the shift solenoid valve (see page 14-217). 18. Replace the shift solenoid harness if the test results
are OK.
19. Install a new O-ring on the shift solenoid wire harness connector, and install the connector in the
transmission housing.
20. Install a new gasket, the dowel pins, and the shift solenoid valve cover.
21. Check the shift solenoid wire harness connector for rust, dirt, or oil, then connect the connector
securely.
22. Refill the transmission with ATF (see step 5 on page 14-232).
23. Install the battery tray, the battery base, and the resonator.
24. Install the air cleaner assembly (see page 11-345) and the intake air duct (see page 11-348).
25. Do the battery installation procedure (see page 22-69).
26. Install the splash shield.
08/08/21 14:46:44 61SNR030_140_0218
ProCarManuals.com
DYNOMITE -2009-