mirror ACURA CSX 2006 Service Owner's Guide


(#'
)


(#'
) Defogger Test
22-30722-307
Power Mirror Switch Test/
Replacement Power Mirror Actuator Test
A
Terminal
Position
UP 26 13
5
DOWN LEFT
RIGHT UP
DOWN
LEFT
RIGHT
L
R 1211
10 A
B
Position Terminal
87 6
TILT UP
TILT DOWN
SWING LEFT
SWING RIGHT
1. Remove the driver’s door grip cover (see page 20-7).
2. Disconnect the 13P connector from the power mirror switch (A), then remove the two screws and
power mirror switch.
3. Check for continuity between the terminals in each switch position according to the table.
4. If the continuity is not as specified, remove the screws and replace the switch.
5. Install the power mirror switch in the reverse order of removal. 1. Remove the door panel (see page 20-7).
2. Disconnect the 8P connector (A) from the power
mirroractuator(B).
3. Check actuator operation by connecting power and ground according to the table.
4. If the mirror fails to work properly, replace the mirror actuator.
5. Check for continuity between terminals No. 1 and No. 2 of the 8P connector. These should be
continuity.
6. If the continuity is not as specified, check for:  Anopeninthewire.
 A faulty mirror holder.
Wire side of
female terminals
08/08/21 14:36:52 61SNR030_220_0309
ProCarManuals.com
DYNOMITE -2009-



Î
(#'
 )
22-308 Power Mirrors
Power Mirror Actuator Replacement
A
A A
CB
A
4.9 N·m
(0.5 kgf·m, 3.6 lbf·ft)
1. Remove the mirror holder (see page 20-34).
2. Remove the power mirror (see page 20-33).
3. Disconnect the 8P connector from the mirror.
4. Record the terminal locations and wire colors.
5. Disassemble the power mirror 8P connector (A), and remove all terminals from it.
6. Remove the screws and the mirror visor (A). 7. Remove the screw from the gasket (A).
8. Remove the three screws (A), and separate the
mirror housing (B) from the bracket (C).
08/08/21 14:36:53 61SNR030_220_0310
ProCarManuals.com
DYNOMITE -2009-




Left:
Right:
22-309
A
B
A B
C BLU/RED
BLK/WHT
YEL/RED
PUR
YEL/BLK YEL/WHT
PNK
BLU/RED
BLK/WHT
BLU/GRN
PUR
BLU/BLK YEL/WHT
PNK
9. Remove the four screws, and the actuator (A).
10. Disconnect the 2P connector (B) from the side turn signal light.
11. Route the wire harness (A) of the new actuator through the hole in the bracket (B) and gasket (C).
12. Install the power mirror actuator, bracket, harness clip, and gasket in the reverse order of removal. 13. Insert the new actuator terminals into the
connector in the original arrangement.
14. Apply tape to seal the intersection of the wire harness and the gasket.
15. Reassemble in the reverse order of disassembly. Be careful not to break the mirror when reinstalling
it to the actuator.
16. Reinstall the mirror assembly on the door.
17. Operate the power mirror to ensure smooth operation.
08/08/21 14:36:53 61SNR030_220_0311
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
22-310Rear Window Defogger
Component Location Index
REAR WINDOW DEFOGGER RELAY
UNDER-HOOD FUSE/RELAY BOX
REAR WINDOW DEFOGGER
CLIMATE CONTROL UNIT
(Has built-in rear window defogger switch/
mirror defogger switch) Test, page 22-70
Function Test, page 22-312
Defogger Wire Repair, page 22-313
Replacement, page 21-75
08/08/21 14:36:54 61SNR030_220_0312
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
22-311
Circuit Diagram
IG2 HOT in ON (II) G12C3
CLIMATE CONTROL UNIT LT GRN
BLK
G603 2 BRN
LT GRN LT GRN
BLK No. 2 (IG) (50 A)
G801
1
RED RED UNDER-HOOD FUSE/RELAY BOX
G504BLK
RED
BRN
No. 8
(30 A)
No. 36
(HAC)
(10 A)
ORN
IGNITION SWITCH
IG2
BAT
WHT
BATTERY
No. 1 (BAT) (100 A)
UNDER-DASH
FUSE/RELAY
BOX
REAR
WINDOW
DEFOGGER
RELAY
REAR WINDOW
DEFOGGER
SWITCH
INDICATOR
(Rear window defogger
switch and defogger
timer circuit built into
the climate control unit.)
NOISE
CONDENSER REAR
WINDOW
DEFOGGER POWER
MIRROR
DEFOGGER
RELAY
H1
D1
J4 F17 F8
2 3
5
1
1 MICU
Q16
08/08/21 14:36:55 61SNR030_220_0313
ProCarManuals.com
DYNOMITE -2009-