ABS ACURA CSX 2006 Service Service Manual

(#'
 

)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0107:
DTC P0108:
YES
NO
YES
NO YES
NO
YES
NO
14-80
Automatic Transmission
DTC Troubleshooting
Manifold Absolute Pressure
(MAP) Sensor Circuit Low Voltage Input
Manifold Absolute Pressure
(MAP) Sensor Circuit High Voltage Input
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it to ON (II) again.
4. Check for Temporary DTCs or DTCs in the PGM-FI SYSTEM with the HDS.
Go to the indicated DTC’s troubleshooting in
the PGM-FI system.
 P0107 (see page 11-80)
 P0108 (see page 11-82) Go to step 5.
5. Check for Temporary DTCs or DTCs in the A/T SYSTEM with the HDS.
Go to step 6.
Intermittent failure, the system is OK at this
time. If any other Temporary DTCs or DTCs were
indicated, go to the indicated DTC’s
troubleshooting.
6. Update the PCM if it does not have the latest software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
7. Start the engine, and wait for at least 2 minutes. 8. Check for Temporary DTCs or DTCs in the A/T
SYSTEM with the HDS.
Check for poor connections or loose
terminals at the PCM. If the PCM was updated,
substitute a known-good PCM (see page 11-7), then
go to step 7. If the PCM was substituted, go to step
1.
Go to step 9.
9. Monitor the OBD STATUS for P0107 or P0108 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 8,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals at the PCM. If the
PCM was updated, substitute a known-good PCM
(see page 11-7), then go to step 7. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 7.
I s DT C P0107 or P0108 i nd i cat ed i n t he PGM -F I SY ST EM?
I s DT C P0107 or P0108 i nd i cat ed i n t he A/ TSY ST EM? I s DT C P0107 or P0108 i nd i cat ed i n t he A/ T
SY ST EM?
Does the HDS ind icate PASSED?
08/08/21 14:39:47 61SNR030_140_0082
ProCarManuals.com
DYNOMITE -2009-


(#'




 )
14-294Transmission End Cover
ATF Feed Pipe Replacement
A
C
G
F
E
D
A
C
F
G
B B
1. Remove the snap rings (A), the ATF feed pipes (B),
and the feed pipe flanges (C) from the end cover (D).
NOTE: Replace the end cover, if the 1st clutch ATF
feed pipe (E) replacement is required.
2. Install new O-rings (F) over the ATF feed pipes.
3. Install the ATF feed pipes in the end cover by aligning the feed pipe tabs with the indentations in
the end cover.
4. Install new O-rings (G) in the end cover, then install the feed pipe flanges over the ATF feed pipes.
5. Secure the ATF feed pipes and the feed pipe flanges with the snap rings.
08/08/21 14:50:14 61SNR030_140_0296
ProCarManuals.com
DYNOMITE -2009-



Outboard Joint Side
16-8Driveline/Axle
Driveshaft Disassembly (cont’d)
A
A
B
A
7. Wrap the splines on the driveshaft with vinyl tape (A) to prevent damaging the boot.
8. Remove the inboard boot. Be careful not to damage the boot.
9. Remove the vinyl tape. 1. Remove the boot bands (A). Lift up the three tabs
(B) using a screwdriver, then release the band. Be
careful not to damage the boot.
2. Slide the outboard boot (A) partially to the inboard joint side. Be careful not to damage the boot.
08/08/21 14:51:24 61SNR030_160_0008
ProCarManuals.com
DYNOMITE -2009-

Î
Î
Î
Outboard Joint Side
Stop ring specifications Model Overall Diameter (A)Wire Diameter
(B)
16-16Driveline/Axle
Driveshaft Reassembly (cont’d)
B
C A
A
B B
A
B A
20. Install a new low profile band (A) onto the boot (B),
then hook the tab (C) of the band.
21. Close the hook portion of the band using commercially available boot band pincers (A), then
hook the tabs (B) of the band.
22. Install the boot band on the other end of the boot, and repeat steps 20 through 21. 1. Wrap the splines with vinyl tape (A) to prevent
damaging the outboard boot.
2. Install new ear clamp bands (B) and the outboard boot, then remove the vinyl tape. Be careful not to
damage the outboard boot.
3. Make sure to check the size of a new stop ring.
To avoid driveshaft and vehicle damage,
make sure you install a new stop ring.
6-speed M/T
model 30.5 mm (1.20 in.) 1.8 mm (0.07 in.)
Except
6-speed M/T
model 24.3 mm (0.96 in.) 1.6 mm (0.06 in.)
Replace.
Replace.
08/08/21 14:51:28 61SNR030_160_0016
ProCarManuals.com
DYNOMITE -2009-


(#'

")


(#'

 )
17-1417-14 Steering
Steering Column Inspection
Steering Lock Replacement
D
B A
E
F
B C
A
B
1. Remove the steering column (see page 17-10).
2. Do these checks:  Check the steering column ball bearing (A) andthe steering joint (B) for play and proper
movement. If any bearing is noisy or has
excessive play, replace the steering column as an
assembly.
 Check the lower slide shaft (C) for smooth movement in and out. If the lower slide shaft is
removed, slip it into the upper shaft by aligning
the paint or stamped marks (D). If it sticks or
binds, replace the steering column as an
assembly.
 Check the sliding capsules (E) for distortion or breakage. If there is distortion or breakage,
replace the steering column as an assembly.
 Check the tilt mechanism and telescopic mechanism for movement and damage.
 Check the absorbing plates (F) for distortion or breakage. If there is distortion or breakage,
replace the steering column as an assembly.
3. Install the steering column (see page 17-12). 1. Remove the steering column (see page 17-10).
2. Center-punch both of the two shear bolts, and drill
the heads of the bolts off with a 5 mm (0.20 in.) drill
bit. Be careful not to damage the switch body when
removing the shear bolts.
3. Remove the shear bolts from the switch body.
4. Install the switch body without the key inserted.
5. Loosely tighten the new shear bolts.
6. Insert the ignition key, and check for proper operation of the steering wheel lock and that the
ignition key turns freely.
7. Tighten the shear bolts (A) until the hex heads (B) twist off.
8. Rewrite the immobilizer control unit-receiver (see page 22-329), and make sure the immobilizer
system works properly.
9. Install the steering column (see page 17-12).
08/08/21 14:53:18 61SNR030_170_0015
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
17-8 Steering
Steering Wheel Installation
A
B
A D
B
C A
39 N·m
(4.0 kgf·m,
29 lbf·ft)
B
1. Before installing the steering wheel, make sure the front wheels are aligned straight ahead, then center
the cable reel (A). Do this by first rotating the cable
reel clockwise until it stops. Then rotate it
counterclockwise about three full turns. The arrow
mark (B) on the cable reel label should point
straight up.
2. Position the two tabs (A) of the turn signal canceling sleeve (B) as shown. Install the steering
wheel on to the steering column shaft, making sure
the steering wheel hub (C) engages the pins (D) of
the cable reel and tabs of the turn signal canceling
sleeve. Do not tap on the steering wheel or steering
column shaft when installing the steering wheel. 3. Install the steering wheel bolt (A), and tighten it to
the specified torque. Connect the cable reel
subharness connector (B). Make sure the wire
harness is routed and fastened properly.
4. Install the driver’s airbag, and confirm that the system is operating properly (see page 24-188).
5. Do the battery terminal reconnection procedure (see page 22-68), and do these tasks:
 Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
 Make sure the horn and turn signal switches work properly.
 Make sure the steering wheel is centered.
6. After installation, check the steering wheel spoke angle. If the steering spoke angles to the right and
left are not equal (steering wheel is not centered),
correct the engagement of the wheel/column shaft
serrations.
08/08/21 14:53:15 61SNR030_170_0009
ProCarManuals.com
DYNOMITE -2009-

(#' '

)
µ
µ µ
µ
µ
µ
DTC 21-01:
DTC 21-02:
YES
NO YES
NO
YES
NO
17-35
Excessive Change of the Vehicle
Speed Signal (Regular Diagnosis)
Comparison between the Vehicle
Speed and the Engine Speed Signal (Regular
Diagnosis)
NOTE:
 If the MIL is on, troubleshoot the fuel and emissions systems first.
 Even though the system is operating normally, the EPS indicator will come on caused by the detecting
condition of DTC 21-01 or DTC 21-02 when you raise
the engine speed with the vehicle stopped.
 Clear the DTC related to the ABS/VSA.
1. Turn the ignition switch to LOCK (0).
2. Raise the vehicle, and support it with safety stands in the proper locations (see page 1-11), and allow
all wheels to rotate freely.
3. Connect the HDS to the data link connector (DLC).
4. Turn off VSA by using the VSA OFF switch.
5. Start the engine, run the vehicle in the 4th (M/T), or D position (A/T).
6. Check the VEHICLE SPEED in the EPS DATA LIST with the HDS.
The system is OK at this time.
Go to step 7. 7. Check for DTCs in the fuel and emissions system
(M/T) or A/T system (A/T) with the HDS.
Troubleshoot the indicated DTC(s).
Go to step 8.
8. Start the engine, and check the tachometer.
Go to step 9.
Troubleshoot the gauge control module (tach)
(see page 22-241).
9. Turn the ignition switch to LOCK (0).
10. Short the SCS line with the HDS.
11. Disconnect ECM/PCM connector A (44P) and EPS control unit connector D (28P).
(cont’d)
Is t he v ehi cl e speed i nd i cat ed ? Is DT C P07 20, P07 21, P07 22 or P07 23
indicated?
I s t he t achomet er w or k i ng cor r ect l y ?
08/08/21 14:54:03 61SNR030_170_0036
ProCarManuals.com
DYNOMITE -2009-



Installation
17-81
A
B C
D
E
93 N·m
(9.5 kgf·m,
69 lbf·ft)
A
B A
B
(P/N 08798-9013)
1. Install a new rubber stop (A) and a new lock washer (B). Align the lock washer tabs (C) with the slots (D)
on the rack end (E) while holding the lock washer in
place. Repeat this step for the other side of the rack
shaft.
2. Hold the flat surface sections of the steering rack with one wrench, and tighten both rack ends with
another wrench. Be careful not to damage the rack
surface with the wrench.
3. Bend the lock washer (A) back against the flat spots (B) on the rack end ball joint housing. 4. Apply multipurpose grease to the circumference of
the rack end joint housing (A) and lock washer.
5. Apply a light coat of silicone grease (P/N 08798-9013) to the boot fitting grooves (B) on the
rack ends.
NOTE: Make sure not to get any silicone grease on
the terminal part of the connectors and switches,
especially if you have silicone grease on your
hands or gloves.
(cont’d)
Replace.
Replace.
08/08/21 14:55:28 61SNR030_170_0082
ProCarManuals.com
DYNOMITE -2009-



17-82EPS Components
Rack End Removal and Installation (cont’d)
A
B
C
D A
B
BA4mm
(0.16 in.)
6. Center the steering rack within its stroke.
7. Clean off any grease or contamination from the boot installation grooves (A) around the gearbox
housing. Install the boots (B) on the rack ends with
the tie-rod clips (C), and fit the boot end in the
installation grooves in the housing properly.
8. After installing the boots, wipe the grease off the
thread section (D) of the rack end. 9. Install the new boot bands by aligning the tabs (A)
with the holes (B) of the band.
10. Close the ear portion (A) of the band with commercially available pincers Oetiker 1098 or
equivalent (B).
11. Slide the rack shaft right and left to be certain that the boots are not deformed or twisted.
08/08/21 14:55:29 61SNR030_170_0083
ProCarManuals.com
DYNOMITE -2009-

(#'

/)
Brakes
Conventional Brake Components......................
......................
ABS (Anti-lock Brake System)
Components (’06-07 Models) . 19-47
......................
......................
VSA (Vehicle Stability Assist) System
Components (’07-09 Models) . 19-95
................................................................
.....................................................................
........................................
............................................................... ................
............................................... ...................
.......................................... ..................................... ..........
........................................ ...................................
..................................... ....................................
.........................................
...................................................... ....................................... ...........
......................................... ....................................
......................................
........................................... .................................
............................................ .............................
............................................................ ................................
................................................................
.....................................................................
........................................
............................................................... ................
............................................... ...................
.......................................... ..................................... ..........
........................................ ...................................
..................................... ....................................
.........................................
...................................................... ....................................... ...........
......................................... ....................................
......................................
........................................... .................................
............................................ .............................
............................................................ ................................
Special Tools . 19-2
Component Location Index . 19-3
Brake System Inspection and Test . 19-4
Symptom Troubleshooting . 19-5
Brake Pedal and Brake Pedal Position Switch
Adjustment . 19-6
Parking Brake Inspection and Adjustment . 19-7
Brake System Bleeding . 19-9
Brake System Indicator Circuit Diagram . 19-10
Parking Brake Switch Test . 19-11
Brake Fluid Level Switch Test . 19-11
Front Brake Pad Inspection and Replacement . 19-12
Front Brake Disc Inspection . 19-19
Front Brake Disc Replacement . 19-21
Front Brake Caliper Overhaul . 19-22
Master Cylinder Replacement . 19-24
Master Cylinder Inspection . 19-25
Brake Booster Test . 19-26
Brake Booster Replacement . 19-27
Rear Brake Pad Inspection and Replacement . 19-29
Rear Brake Disc Inspection . 19-32
Rear Brake Disc Replacement . 19-34
Rear Brake Caliper Overhaul . 19-35
Brake Pedal Replacement . 19-36
Brake Hose and Line Inspection . 19-37
Brake Hose Replacement . 19-38
Parking Brake Cable Replacement . 19-40
Parking Brake Lever Grip and Cover Replacement . 19-41
Brake Pedal Cover Replacement . 19-45
08/08/21 15:00:43 61SNR030_190_0001
ProCarManuals.com
DYNOMITE -2009-