error 1 ACURA CSX 2006 Service Manual Online

Muting Logic
LCD Unit LimitationsSymptom Duplication
23-267
The accuracy of the GPS is reduced during these
instances:
 Metallic window tinting above the GPS antenna.
 When only three or less satellite signals are received (Four satellite signals are required for accurate
positioning).
 When driving near high tension power lines.
 When the satellite control centers are experiencing problems.
Whenever the navigation system is giving guidance,
the front speakers are muted. When the voice control
system is being used, all of the speakers are muted. If
the HandsFreeLink is in use, the voice control system is
unavailable and a message appears onscreen.
NOTE: The screen is not touch sensitive. Use the
interface dial and buttons to select items on the screen.  In cold temperatures, the display may stay dark for the first 2 or 3 minutes until it warms up.
 When the display is too hot because of direct summer sunlight, it will remain dark until the temperature
drops (you may see an error message displayed
stating this fact).
 When the humidity is high and the interior temperature is low, the display may appear cloudy.
The display will clear up after some use.
 Fingerprints on the screen may be noticeable. Clean the screen with a soft, damp cloth. You may use a
mild cleaner intended for eye glasses or computer
screens. To avoid scratching the panel, do not rub too
hard or use abrasive cleaners or shop towels.  When the symptom can be duplicated, verify that it is
not a characteristic of the system. Review the
navigation system manual and compare it to a
known-good vehicle (with the same software and
database), under the same conditions. If the
symptom is not the same as the known-good vehicle,
follow the self-diagnostic procedures and the
appropriate troubleshooting procedures.
 When the symptom does not reappear or only reappears intermittently, ask the client about the
conditions when the symptom occurred.
– Always ask the client to demonstrate the problem.
– Trytoestablishpossibleusererrorora misunderstanding of the system.
– Try to establish if outside interference may have been the cause.
– Try to duplicate the symptom under the same conditions the client experienced.
– Vibration, temperature extremes, and moisture (dew, humidity) are factors that are difficult to
duplicate.
– Inspect the vehicle for after-market electronic devices (vehicle locators, amps, radar detectors,
etc.) that may be hidden.
When troubleshooting navigation system problems,
ensure that the known-good vehicle is the same
software version year and model as the vehicle being
serviced. Mixing incompatible navigation DVDs or
other system components can delay the
troubleshooting process by creating symptoms or
issues causing effects unrelated to the original problem.
(cont’d)
08/08/21 14:14:21 61SNR030_230_0270
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
ÃŽ
DVD Handling and CleaningEarliest DVD Version Application for Each
Model
23-270 Navigation System
General Troubleshooting Information (cont’d)
To avoid damaging or leaving fingerprints on the DVD,
always handle it by the edges and place it in a jewel
case whenever it is outside the navigation unit. Deep
scratches or fingerprints on the back of the DVD can
cause intermittent rebooting or other system errors.
Smudges and fingerprints can be carefully removed
using a mild cleaner and tissues designed to clean
eyeglasses. To clean a DVD, use a clean soft cloth. Very
gently wipe across the DVD from the center to the
outside edge, never in a circular motion.
Do not place stabilizer rings or labels on the DVD. Each navigation system DVD contains a map/POI (point
of interest) database and the navigation system
software for each model that it supports. Inserting an
older DVD can cause problems since it lacks the
software to provide the specific features needed for that
model. Unfortunately, the navigation software does not
detect or warn you that the version is outdated, and it
may even appear to operate.
NOTE: Replacing a DVD just because the version
number is higher is not always warranted. A higher
software version does not necessarily mean it contains
newer software for your model. The DVD contains
software for all models that use the same color DVD,
and a revised number may or may not have software
fixes or upgrades for the model in question.
Typical warning symptoms that an outdated DVD is
being used include:
 The Acura model navigation screen may display a Honda logo while booting up.
 A newly introduced model feature or current accessory may not display properly, and Extension
will display instead.
NOTE: Extension may be displayed when using
Music Link, but should never be displayed when XM
is selected.
 The current street (the street being driven on) does not appear properly at the bottom of the map screen
display when the vehicle is driven on a main road.
NOTE: If necessary, compare the operation to the
navigation system of the same model and year
vehicle that has a current DVD.
08/08/21 14:15:39 61SNR030_230_0273
ProCarManuals.com
DYNOMITE -2009-

How to Identify Navigation DVD Versions,
and How to Inspect A DVD for Damage
23-271
To determine the navigation version on a particular
model, start the engine, then locate the navigation unit.
Open the DVD door, and push the eject button to eject
the DVD. Hold the DVD by the edges, and check for
these items: Check any official Acura service website for more service information about the navigation DVDs.
 The DVD label color.
 Read the DVD version on the label, and note it on the repair order. The version number is near the bottom
of the label text (for example, ver: 4.23A). You will
need this version number:
– To verify that the DVD version is appropriate for the vehicle. Check any official Honda service website
for more service information.
– Any time you call Tech Line regarding a navigation system issue.
– To answer client inquires concerning update or coverage issue.
NOTE: Client’s may obtain DVDs from sources
outside the normal ordering process. If you
determine this is the case, recommend that your
customer purchase the appropriate DVD from the
Acura Disc Fulfillment Center (see ORDERING A
DVD).
– Check the underside of the DVD for signs of mishandling. Deep scratches, or random scratches,
light swirl marks, or fingerprints can cause random
lock-ups, reboots, erratic voice response, erratic
positioning errors, and DVD read or format errors.
NOTE: A damaged DVD is not covered under
warranty unless the disc is damaged by the
navigation unit. Damage by the navigation unit
typically appears as circular scratches caused by
something rubbing against the DVD as it spins. The
damage may appear as arcs or complete circles on
the DVD reading surface.
– Verify that the underside of the DVD is silver, and not a copy with a blue color. Copies will not work
properly and can cause other symptoms that mimic
hardware problems.  Incorrectly colored DVDs being put into navigation
vehicles. This causes the system to either display
error messages, or causes system malfunctions that
mimic a hardware problem. This results in the client
leaving with a malfunctioning navigation system.
 The DVD version provided to the client is out-of date or incompatible with a particular model. This
inconveniences your client by delaying the repair, or
by causing additional (and unnecessary) returns to
your dealership.
 The client experiences bugs or other issues that have already been resolved in later versions currently
available at the fulfillment desk.
If the DVD is defective, or has any of the issues
mentioned above, return the vehicle to your client and
recommend that they order the proper DVD from the
Acura Disc Fulfillment Center.
NOTE: Navigation DVDs do not come with replacement
navigation units. If you are replacing a navigation unit
because it is defective (following appropriate service
manual troubleshooting), and the DVD does not eject,
order a DVD. See Obtaining a navigation DVD.
(cont’d)
08/08/21 14:15:39 61SNR030_230_0274
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
ÃŽÃŽ
ÃŽ
How to Check Error History
Hardware Error History
Software Error (Soft error) History
23-273
Return
System Links Help
Exit Diag
ReturnReturn
Navi.ECUSelect Diagnosis Items Self- Diagnosis Mode
Detail Information & Setting
(Navi will check internal function. connections, etc.
Perform this test with vehicle stopped and engine running.)
(Individual Diagnostic screens to confirma specific diagnostic screen.)
XM
Error
History
Yaw
Sensor Car Status
ECU Info. Hard Key
DVD Mic
HFL
Press any icon if you want to see details. GPS Ant. R. Camera
Display Radio
A/C
Return
ReturnError History
Hard Error Soft Error
Hard Error
Clear Save
0/0
1. 2705 HFL Diag
2004:12:31 - 19:15:55
2. 2707 Mic Diag 2004:12:31 - 19:15:50
2. 2707 GPS Diag:Antenna
2004:12:31 - 19:15:12
The Error History feature is to record intermittent
navigation issues that occur while using the system.
Sometimes the client complaint cannot be duplicated.
The error history may record the information needed to
diagnose the problem. To check the error history:
1. Start the engine.
2. Press and hold the MAP/GUIDE, MENU, and CANCEL buttons for 3 seconds.
3. When the Select Diagnosis Items menu is displayed, select Detail Information & Setting.
4. When the navigation unit has hard codes, the Error History icon appears yellow when the Self
Diagnosis mode (System links) screen is displ ayed.
When no hard errors are stored, the icon appears
gray. To view the errors with their DTC codes,
select the error history icon. 5. Select Hard Error.
NOTE: Soft errors are for factory use only.
6. The Hard Error screen displays the following information for each error:
 The DTC trouble code for the error
 A brief description of the DTC code
 The date and time when the error occurred.
NOTE:  To see additional errors, use the joystick to select UP or DOWN.
 Select Clear to delete the error history. The Save feature is for factory use only.
7. Use the DTC Symptom Troubleshooting table to troubleshoot the error.
8. Clear the DTCs.
9. Select Return to exit the error history.
Software errors are not available. They are for factory
use only.
(cont’d)
08/08/21 14:15:40 61SNR030_230_0276
ProCarManuals.com
DYNOMITE -2009-

ÃŽ

ÃŽ

ÃŽ

ÃŽ



How to Clear Error History
Hard error history is displayed
Soft error history is displayed (Soft errors are for
factory use only)Hard error history clear
Soft error history clear (Soft errors are for factory
use only)
23-274Navigation System
General Troubleshooting Information (cont’d)
Return
Return Return
ReturnHard Error
Clear Save
0/0
1. 2705 HFL Diag
2004:12:31 - 19:15:55
2. 2707 Mic Diag 2004:12:31 - 19:15:50
2. 2707 GPS Diag:Antenna
2004:12:31 - 19:15:12
Soft Error
1. APPLI 31000001 (2004:12:31 - 19:15:08)
00000000
2. APPLI 31000001 (2007:03:01 - 10:53:54)
3. APPLI 12004100 (2004:12:31 - 19:15:12)
Clear Save
0/0
00000000 00000000 00000000
00000000 00000000 00000000 00000000
00000001 00000105 ffffff2c 00000000 Hard Error
Yes No
Clear Error History
Soft Error Yes No
Clear Error History
1. Do the steps in How to check Error History.
2. Select Clear in the error menu.
NOTE: By selecting Clear, all software and hardware errors stored in history are erased at the same
time.
 Save is for factory use only. 3. After selecting Clear, then selecting Yes, both Hard
Error history and Soft Error history are cleared at
thesametime.
4. Press return to exit.
08/08/21 14:15:40 61SNR030_230_0277
ProCarManuals.com
DYNOMITE -2009-

(#'#
)
DTC Description CircuitFailure DetectionPageAlso Check for
23-275
DTC Troubleshooting Index




1001 FROM system Info
Error Navigation unit internal data error. (see page 23-320) Low or weak battery
voltage
1101 Media Bus Send Error Media
condition
monitoringNavigation unit internal media error. (see page 23-320) Low or weak battery
voltage
1201 DVD High Temp DVD drive Navigation unit temperature above the upper limit. Failure in navigation unit fan circuit. (see page 23-321) Low or weak
battery voltage
High temperature
around the
navigation unit
1202 DVD Low Temp DVD drive Navigation unit temperature below the lower limit. (see page 23-321) Low or weak
battery voltage
High temperature
around the
navigation unit
1301 GPS Antenna Error GPS AntennaGPS antenna circuit malfunction. (see page 23-322) Low or weak battery
voltage
1302 GPS Receiver Error 1 GPS
ReceiverGPS antenna circuit malfunction.
Navigation unit internal GPS receiver
malfunction. (see page 23-323) Low or weak battery
voltage
1303 GPS Receiver Error 2 GPS
ReceiverNavigation unit internal GPS receiver
malfunction. (see page 23-324) Low or weak battery
voltage
1305 Gyro Error 2: ECU Temp XX °C Gyro Navigation unit internal gyro malfunction. (see page 23-324) Low or weak battery
voltage
1306 Vehicle Speed Pulse Vehicle
Speed PulseVSP circuit malfunction. (see page 23-325) Check for F-CAN
DTCs
1307 DVD Read Error DVD Scratched/Dirty DVD or navigation unit internal DVD ROM drive. (see page 23-325) Low or weak battery
voltage
1402 Audio Error 2 CD Mechanical malfunction in the CD changer. (see page 23-326) Low or weak battery voltage
1409 Audio Error 9 XM XM Antenna/circuit malfunction. (see page 23-326) Low or weak battery voltage
2607 XM Diag XM GA-NET Bus circuit malfunction Open/Short. XM Antenna circuit malfunction. (see page 23-327)
2609 VRAM Diag ECU VRAM Navigation unit internal VRAM malfunction. (see page 23-329)
2610 DRAM Diag ECU DRAM Navigation unit internal DRAM malfunction. (see page 23-330)
2701 GPS Diag: Antenna GPS GPS antenna malfunction. (see page 23-330)
2702 GPS Diag: Receiver in Navi GPS GPS antenna malfunction. (see page 23-331)
2703 Aircon Diag Aircon Communication error between climate control unit and navigation unit (open/short). (see page 23-331) Check for F-CAN
DTCs
2705 HFL Diag HFL HandsFreeLink control unit internal malfunction. (see page 23-334) Check for F-CAN DTCs
2706 Gyro Diag: ECU Temp XX °C Gyro Navigation unit internal malfunction. (see page 23-336)
2707 Mic Diag Mic Mic circuit malfunction Open/Short. (see page 23-337)
Flash ROM
management
08/08/21 14:15:41 61SNR030_230_0278
ProCarManuals.com
DYNOMITE -2009-

SymptomDiagnostic procedure Also check for
23-277

















 







Voice guidance cannot be heard, is
broken up, or there is static
Symptom Troubleshooting
(see page 23-341) Volume or voice feedback setting
(see Owner’s manual)
Navigation unit
Stereo amplifier
Harness/fuses/switches
Voice control does not work/
respond Symptom Troubleshooting
(see page 23-342) Navigation unit
The wrong color DVD is installed
The DVD is damaged or dirty
Microphone harness/switches
HandsFreeLink control unit
Navigation cannot control HVAC by
voice command Symptom Troubleshooting
(see page 23-346) The wrong color DVD is installed
Harness/fuses/switches
Wrong navigation unit (model
code)
Navigation cannot control XM radio Symptom Troubleshooting (see page 23-350)Low or weak battery
Navigation cannot control audio
system Symptom Troubleshooting
(see page 23-349)Wrong color DVD
Navigation display buttons do not
work or respond properly Symptom Troubleshooting
(see page 23-340) Navigation unit
Open/short between the XM
receiver or the GA-Net bus
The wrong color DVD is installed
The DVD is damaged or dirty
Today’s Destinations button is dim
and not selectable in the Enter
destination by screen (grayed-out) The client has not entered a group
of locations for Today’s Destinations.
This is normal. The button is only
selectable if the client is using this
functionSee Owner’s Manual
Some set-up and information
functions of the navigation system
are grayed-out and do not work Client did not select OK from
Disclaimer screen. Refer to System
Function Diagram (see page 23-289)
Previous Destinations button is dim
and not selectable in the Enter
destination by screen (grayed-out) The vehicle may be new, or the
customer deleted the destination.
Enter a destination, and allow the
system to route to it. After the trip,
the Previous Destinations button
will be selectable
Address cannot be found or system
gives poor routing Verify proper operation and
system limitations using the
owner’s manual.
See Answering client question
Navigation coverage in general
troubleshooting
Refer to Database limitation in the
navigation system manual to
report database errorsDatabase limitations (address not
in database)
The wrong color DVD is installed
OPEN/CLOSE function of the display
does not work Symptom Troubleshooting
(see page 23-351) Navigation unit
Harness
Navigation display will not close Symptom Troubleshooting (see page 23-352) Navigation unit
Harness
Navigation display does not open or
opens part way Symptom Troubleshooting
(see page 23-352) Navigation unit
Harness
(cont’d)
08/08/21 14:15:41 61SNR030_230_0280
ProCarManuals.com
DYNOMITE -2009-

SymptomDiagnostic procedure Also check for
23-278Navigation System
Symptom Troubleshooting Index (cont’d)

















PC card will not play/card icon on
audio screen cannot be selected
Symptom Troubleshooting
(see page 23-234)Navigation unit
Navigation display stays on with
ignition switch in LOCK (0) Symptom Troubleshooting
(see page 23-349) Harness/fuses/switches
Aftermarket accessories
connected to the system
DVD read error messages Symptom Troubleshooting (see page 23-346) Navigation unit
The wrong color DVD is installed
Damaged DVD
Navigation system will not go
beyond the disclaimer screen and
displays the OK button See navigation display buttons do
not work or respond properly
The wrong color DVD is installed
Scratched or damaged DVD
Navigation unit
The navigation anti-theft code card
is lost or missing See anti-theft feature (see page
23-266)
The vehicle icon lags behind when
the vehicle turns See self-inertial navigation
limitations (see page 23-266) Aftermarket accessories
connected to the system
GPS antenna/cable
Navigation screen is darker than
normal or takes time to brighten
when it is cold See LCD unit limitations (see page
23-267)
The navigation clock is off by 1 to 3
hours after replacing the navigation
unit See service precautions (see page
23-268)
Perform map matching (see page
23-269)
GPS antenna/cable
Check and adjust the clock
settings
A new navigation DVD is needed See obtaining a navigation DVD (see page 23-269)
Time is not correct Reset Time Adjustment in set-up The wrong colored DVD or version is installed
The DVD is scratched or dirty See DVD Handling and Cleaning (see page 23-270)Navigation unit
The wrong DVD was installed and
now the system does not function
properly See Precaution client Sneak
Previews (see page 23-272)
Install the correct version DVD
Check any official Honda service
website for more service
information about the navigation
system.
A specific city cannot be found See How to answer client questions about navigation coverage
(see page 23-272) The DVD is scratched or dirty
Refer to Database limitation in the
navigation system manual to
report database errors
The Honda Globe Screen (not the
Acura Globe Screen) appears every
time the vehicle is started Symptom troubleshooting
(see page 23-354)
Also see the symptom The wrong
DVD was installed and now the
system does not function properly
08/08/21 14:15:41 61SNR030_230_0281
ProCarManuals.com
DYNOMITE -2009-

ItemDefinition
23-288Navigation System
System Description (cont’d)
LCD
Liquid Crystal Display (the navigation screen)
Map matching The received GPS information allows the navigation system to position the vehicle on the map. MAP
matching has occurred if the map screen displays the current street name in the bottom-shaded area.
Mic Abbreviation for the microphone used for receiving voice commands. It is located near the map light in the
ceiling. The ANC circuit may also use it to check its tuning.
MID Multi-Information Display
MW Maneuver Window. While on route to a destination, this window displays information about the next
maneuver.
Navi Abbreviation for the Navigation System.
Off-road tracking See bread-crumbs.
Off route This occurs when the user leaves mapped roads. Off road tracking dots (bread-crumbs) are displayed If the
option is enables in the setup menu. The user can use them to return to a mapped road. The bottom of the
navigation screen displays not on a digitized road.
Outlying areas These are rural areas that typically have only their main roads mapped. All other roads are shown in light
brown for reference only, since the have not been verified.
Paired Linking your call phone to the HFL.
PC Card Slot The PC Card (PCMCIA, type II) slot is for factory use only. Make sure that the sliding door is closed at all
times, if opened, an error message is displayed on the screen.
PCM Powertrain Control Module. This unit supplies the navigation system speed signal, also refered to as PCM.
PCMCIA A computer industry defined term referring to the PC Card slot standard.
PIN Personal Identification Number, a random 4 digit number created by the customer to protect personal
information.
POI Point Of Interest. These are the businesses, schools, etc. found under the places option on the main menu.
Polygon Colored areas on the map screen denoting parks, schools, etc. See the Navigation System Manual Driving to
Your Destination for a list of the assigned colors.
QWERTY Keyboard layout resembling the typewriter keys. The keyboard layout can be changed to an alphabetical
layout in the Setup mode.
SCS connector The service check signal 2-pin connector used to put the navigation system into the diagnostic mode.
Security code Code needed to activate the navigation system. You can get the security code from the in by entering the
navigation unit serial number. You can find the serial number on the diagnostic screens (unit check, Navi
ECU), or on the underside of the navigation unit.
Tuning A continual update of internal navigation system scaling factors. See the individual sensor tuning
discussions under either System Description, or System Diagnosis Mode (see page 23-297).
Unverified streets These streets have not been verified for turn restrictions, one-way, etc. They appear light brown on the map.
You can enter address destinations in these areas, but depending on your Unverified. Routing choice in
setup, voice guidance may end at the last verified street closest to your destination.
USB Universal Serial Bus. The USB is used for playing the compressed audio files (MP3, WMA, and AAC) on the
external device through the audio unit.
Verified streets These streets consist of the detailed metropolitan coverage areas, and other inter-town connection roads.
These roads are shown in black or red on the map. (interstates are red)
VP Vehicle Position. When in map mode, this circular icon shows the vehicle position on the map.
VR Voice Recognition. This allows voice control of many of the navigation functions. The hardware consists of
the microphone, voice control switch (navigation TALK/BACK buttons), and the center speaker. See the
overview for more information.
VSP Vehicle Speed Pulse. This pulse signal coming from the PCM (VIA the CSS) is used to update the Vehicle
position on the map. These pulses do not indicate direction (forward or backward). When in reverse, the
navigation receives a signal and directs the VP to move backwards on the map.
XM This device receives information from the XM satellites and passes XM audio information to the audio unit.
In addition, traffic information is sent to the navigation unit.
Yaw sensor This device is located in the navigation system control unit and senses the side-to-side twisting force
generated when the vehicle turns. See a detailed description of how this sensor works in system description.
08/08/21 14:15:44 61SNR030_230_0291
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
ÃŽ
(#'#
)
Start-up procedure and Diagnostic Menu System Links
23-297
System Diagnostic Mode
Return System LinksHelp
Exit Diag
ReturnReturn
Navi.ECUSelect Diagnosis Items Self- Diagnosis Mode
Detail Information & Setting
(Navi will check internal function. connections, etc.
Perform this test with vehicle stopped and engine running.)
(Individual Diagnostic screens to confirma specific diagnostic screen.)
XM
Error
History
Yaw
Sensor Car Status
ECU Info. Hard Key
DVD Mic
HFL
Press any icon if you want to see details. GPS Ant. R. Camera
Display Radio
A/C
Start the vehicle, and at the disclaimer screen use the
navigation display hard buttons as described below:
Make sure the battery is in good condition, then press
and hold the three buttons MAP/GUIDE, MENU, and
CANCEL, for about 3 seconds. The display screen goes
directly to the Select Diagnosis Items menu shown
below.
 Self-Diagnosis Mode (runs the automatic diagnosis of the navigation system)
 Detail Information & Setting (allows you to manually diagnose the navigation system) 1. By selecting Self-Diagnosis Mode from the
navigation screen main menu. The message at the
bottom of the screen flashes indicating the
diagnostic is running. Make sure you enter the
audio anti-theft code.
NOTE: The system cannot complete a full diagnosis unless the engine is running.
 DTC 2703 can be stored when the ignition switch is at ACCESSORY (I). With the ignition switch is
in ACCESSORY (I), the climate control unit is
turned off and the navigation unit loses
communication and stores DTCs. Therefore,
there is a possibility that the system is normal
even DTC 2703 is stored. Check system links with
the engine running, and if it shows normal, the
system is OK at this time.
2. Select the icon you want to diagnose. Push in the select the icon to see the details of that diagnostic
function.
(cont’d)
08/08/21 14:15:48 61SNR030_230_0300
ProCarManuals.com
DYNOMITE -2009-