error 1 ACURA CSX 2006 Service Owners Manual

Icon
Colors Description
23-298Navigation System
System Diagnostic Mode (cont’d)
The System Links function runs automatically and
displays a flashing message at the bottom of the
screen reminding you to have the engine running
for the test. The diagnostic tests the following:
 Most of the wires connecting the navigation components shown in the block diagram.
 The results from the various components shown in the block diagram.
 The microphone is tested by listening to the bong sound produced by the navigation unit from the
speakers when the diagnostic is started. This
requires that the audio system be operating
normally.
When the diagnostic finishes, the icons turn
different colors based on their test status. The color
definitions are shown below and can also be seen
by selecting Help on the System Links screen.
The indication on the screen may not change until
you exit and reenter the Self-Diagnosis mode. In
some cases, you may have to restart the engine for
the indication to change. After you repair the
affected component or harness, repeat this
diagnostic. Explanation of each icon
Each icon color is explained in the table below.
Green The system ran a diagnosis and the results are OK.
Red Errors that require replacement of hardware or harness. Examples
are connection error or memory
diagnosis errors. Troubleshooting
for DTCs.
Yellow Errors that doesn’t require hardware replacement, such as an
open display cover, an incorrect
DVD, leaving the vehicle in
ACCESSORY (I), or because of a
missing accessory, like the
rearview camera.
White The diagnosis is running. The screen functions are locked out
while the diagnosis is runs.
Gray The system cannot automatically check this function. You have to
select the diagnosis item and
manually do additional testing,
like checking the navigation
buttons in the Hard Key test.
When you complete the Hard Key
test and return to the System
Links menu, the gray icon turns
green.
NOTE: By selecting the HELP icon, you can see a
description for each color.
08/08/21 14:16:38 61SNR030_230_0301
ProCarManuals.com
DYNOMITE -2009-

••••••
•••
••• •••
••• ••• ••• •••
•••
••• ••• ••• •••
Icon Icon Color
GREEN RED YELLOW WHITE GRAY
23-300Navigation System
System Diagnostic Mode (cont’d)
Mic
The microphone
detects the
sound ‘‘Pi-Pi-
Pon’’ at the
system link
menu. The microphone
could not detects
the sound ‘‘Pi-Pi-
Pon’’ at the
system link
menu. Executing (Not
completed)
ECU Info. Both V-RAM or D-RAM is OK,
and all Program
Flash, Serial No.,
Model is
available, and
the DVD lid is
closed.Either the
V-RAM or D-
RAM is NG, or
any of the
Program Flash,
Serial No.,
Model is
unavailable.DVD lid is
opened
Executing (Not
completed)
Hard Key All buttons are pressed and are
detected under
Hard key menu.All buttons are
not pressed or
pressed but not
detected under
Hard key menu,
or exit from Hard
key menu
without the
button not
detected. Until changing to
Hard key menu.
Error History Hard Error or
Soft Error is
detected under
Error History
menu. Executing (Not
completed)
Hard Error or
Soft Error is not
detected under
Error History
menu.
DVD DVD mechanism
is normal and
the proper DVD
is installed. Improper DVD is
installed, or DVD
is not installed,
or can not
identify software
version from the
DVD or internal
mechanism
failure.Executing (Not
completed)
Yaw Sensor Result of the Yaw Sensor
diagnosis menu
is OK.Result of the
Yaw Sensor
diagnosis menu
is NG.Result of the
Zero Point
Output under the
Yaw Sensor
diagnosis menu
is NO CHECK.Executing (Not
completed)
Car Status Check these
systems
manually.
08/08/21 14:16:39 61SNR030_230_0303
ProCarManuals.com
DYNOMITE -2009-

´µ ´µ
ÃŽ
ÃŽ ÃŽ
ÃŽ
ÃŽ
´
µ
´
µ
´µ
Hard Key
Yaw Sensor DVD
Aircon
HFL
23-308Navigation System
System Diagnostic Mode (cont’d)
Hard KeyReturn
Return
ZOOM OUT ZOOM IN
CANCEL SET UP MAP
MENU INFO
MODE CH
CH
VOL
VOL
FF
REW
RPT RDM
SEEK UP SCAN
AUDIO
CD/AUX
AM/FMSKIP
SKIP
SEEK DOWN Keep Pushing to Return.
Yaw Sensor
Zero Point Output OK OK
Output Value x.xxxV
Current Offset x.xxxV
Temperature in ECU xx°C
Return
Return
ReturnDVD
Error Detail -
Version 20050404
Maker ID 0x01
Navi Platform 0x01
Connection OK Aircon
HFL
Connection OK
This diagnostic screen checks the status of each of the
hard buttons surrounding the navigation display. When
you press each hard button, the corresponding item on
the screen should flash blue. Touch the return key, or
press and hold the joystick to exit.
NOTE: It is normal for the VOL ( , ) CH ( , ) and
MODEbuttontobeinactive.
This screen gives a quick test of the yaw sensor
functionality based on the two voltages Sensor and
Offset. For more information see the Yaw Rate
Diagnostic. This diagnostic tests the navigation DVD reader.
This diagnostic tests the climate bus connection (AC-SI
and AC-SO) between the navigation unit and climate
control unit. Make sure the engine is running for this
test.
 This checks the 4 wire communication bus between the HFL and the navigation.
 When connection is shown with NG, check the connection between the navigation unit and the
HandsFreeLink control unit.
08/08/21 14:16:42 61SNR030_230_0311
ProCarManuals.com
DYNOMITE -2009-

QuestionAnswer
23-318Navigation System
System Diagnostic Mode (cont’d)










Why wont the Export or Import
functions work? What do I check as
part of troubleshooting?
The card may not be fully inserted into the slot. Eject the PC card, and
inspect for warping or damage to the edge connector. Never use
excessive force to insert a PC card. This can damage the pins in the
rear of the slot.
The PC card may not contain files that are recognized by the new
navigation unit. Navigation data can only be transferred between
navigation units with the same Model code, and with the same navi
Program flash version.
The flash memory chip type may not be accepted by the system. Only
Compact Flash and ATA cards have been tested.
The card’s PCMCIA adaptor may prevent a known-
good PC card from
being recognized. Avoid multi-slot type PCMCIA adaptors that accept
several different flash memory types.
The card may be full and as a result the files are stored, but without
any data. Export and import appear to function, but move nothing.
Delete unused files from the PC card.
There may not be any files on the PC card. If the PC card has a write
protection switch, make sure it is turned off before using the Export
function.
Although flash memory chips are reliable, occasionally they develop
bad sectors or other formatting errors that prevents them from
accepting files. The PC card should be reformatted using the FAT
format.
The PC card may have been formatted using the format NTFS. Only the
FAT format is accepted by the system.
Hard Disc Drive (HDD) cards may not work properly in the system and
can overheat or quit functioning, particularly in a hot vehicle. They are
not recommended.
Before performing the Import function, ensure that the original
navigation DVD is loaded into the new navigation unit and working
properly.
08/08/21 14:16:45 61SNR030_230_0321
ProCarManuals.com
DYNOMITE -2009-

µ
Error Message Table
Screen Error MessageSolution
23-319
Navigation system is unable to acquire a
proper GPS signal.Make sure there is nothing on the dashboard blocking the GPS
antenna.
If not, move the vehicle to an open space away from tall buildings,
trees, etc.
Aftermarket metallic wi
ndow tinting and other aftermarket devices
can affect the GPS reception.
Navigation unit door is open or No DVD
disc installed. Please check system. Make sure the navigation DVD is the correct color and is not
scratched or damaged. Make sure it is installed with the label side up
and the navigation unit door is snapped fully closed.
No DVD disc, please check system. Check that the navigation DVD is installed with the label side up.
Display temp is too high. System will shut
down until display cools down. This message appears briefly when the display temperature is too
high, and then the display turns off until the temperature cools down.
The system turns back on when the display cools down.
Outside temperature is low, system will
take a while to start up. The temperature is below 30 °C and the navigation unit has
difficulties reading the navigation DVD. The system will start up
when the temperate warms up.
DVD disc reading error (unformatted),
please consult your dealer. Check the navigation DVD for the correct color and software version.
Also check for deep scratches or other damage. Make sure you are
using an official Acura navigation DVD. The system cannot read
other mapping databases or video DVDs. Check any official Acura
service website for more service information about the navigation
system.
Route has not been completed. Please try
again from a different location. Routing to or from a place (new area) that is not in the database. Try
planning a different route to or from a different location that is
clearly displayed on the map (map matched).
No alternate route found. Original route
will be guided. No alternate route method was found. The original route method will
be used.
This destination cannot be found in
database. The destination was not found in the database. Try another
destination nearby, or select the destination with the jog dial.
08/08/21 14:16:45 61SNR030_230_0322
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#

)(#'# 
#


)
µ
µ µ
µ
DTC 1001: DTC 1101:
YES
NO YES
NO
23-32023-320Navigation System
DTC Troubleshooting
FROM System Info Error
Media Bus Send Error
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Turn the ignition switch to LOCK (0), and then back to ON (II).
2. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355),
because there is an internal problem with the
Flash-ROM.
Intermittent failure, the system is OK at this
time. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-255).
Intermittent failure, the system is OK at this
time.
Is DTC 1001 indicated?
I s DT C 1101 i nd i cat ed ?
08/08/21 14:16:45 61SNR030_230_0323
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#

)µµ
µ
µ(#'# 
#
)
µ
µ µ
µ
DTC 1201: DTC 1202:
YES
NO YES
NO
23-32123-321
DVD High Temp
DVD Low Temp
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 This code sets when the internal temperature of the navigation unit ECU rises above 70 °C (158 °F). The
unit is designed to shut down to protect the
navigation unit ECU. This could be caused by an
inoperative navigation unit ECU fan or if the
passenger’s compartment temperature exceeds the
maximum. Do the troubleshooting when the unit is
within the allowable temperature range.
1. Check that the temperature is below 70 °C (158 °F) in the passenger’s compartment.
2. Clear the hard error code (see page 23-274).
3. Turn the ignition switch to LOCK (0), and then back to ON (II).
4. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time. If the unit repeatedly comes back with the
DTC, replace the navigation unit. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 This code sets when the internal temperature of the navigation unit ECU falls below 20 °C ( 4 °F). The
unit is designed to shut down to protect the
navigation unit ECU. This is usually caused by very
cold exterior temperatures. Do the troubleshooting
when the unit is within the allowable temperature
range.
1. Check that the temperature is above 20 °C ( 4 °F) in the passenger’s compartment.
2. Clear the hard error code (see page 23-274).
3. Turn the ignition switch to LOCK (0), and then back to ON (II).
4. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.
I s DT C 1201 i nd i cat ed ? I s DT C 1202 i nd i cat ed ?
08/08/21 14:16:45 61SNR030_230_0324
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#

)
µ
µ µ
µ
µ
µ
DTC 1301:
YES
NO YES
NO
YES
NO
23-322Navigation System
DTC Troubleshooting (cont’d)
GPS Antenna Error
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside, away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Go to step 4.
Intermittent failure, the system is OK at this
time. 4. Turn the ignition switch to LOCK (0).
5. Check for poor connections or loose terminals at
the navigation unit connector H (2P).
6. Clear the hard error code.
7. Turn the ignition switch to LOCK (0), and then back to ON (II).
8. Check for the hard error code.
Go to step 9.
Intermittent failure, the system is OK at this
time.
9. Turn the ignition switch to LOCK (0).
10. Replace a known-good GPS antenna (see page 23-358).
11. Turn the ignition switch to ON (II).
12. Clear the hard error code.
13. Turn the ignition switch to LOCK (0), and then back to ON (II).
14. Check for the hard error code.
Replace the original GPS antenna.
Replace the navigation unit (see page 23-355).
Is DTC 1301 indicated? Is DT C 1301 ind icated ?
Is DT C 1301 ind icated ?
08/08/21 14:16:45 61SNR030_230_0325
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)
µ
µ µ
µ
µ
µ
DTC 1302:
YES
NO YES
NO
YES
NO
23-323
GPS Receiver Error 1
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside, away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Go to step 4.
Intermittent failure, the system is OK at this
time. 4. Turn the ignition switch to LOCK (0).
5. Check for poor connections or loose terminals at
the navigation unit connector H (2P).
6. Clear the hard error code (see page 23-274).
7. Turn the ignition switch to LOCK (0), and then back to ON (II).
8. Check for the hard error code (see page 23-273).
Go to step 9.
Intermittent failure, the system is OK at this
time.
9. Turn the ignition switch to LOCK (0).
10. Replace a known-good GPS antenna (see page 23-358).
11. Turn the ignition switch to ON (II).
12. Clear the hard error code (see page 23-274).
13. Turn the ignition switch to LOCK (0), and then back to ON (II).
14. Check for the hard error code (see page 23-273).
Replace the original GPS antenna.
Replace the navigation unit (see page 23-355).
Is DTC 1302 indicated? Is DTC 1302 indicated?
Is DT C 1301 ind icated ?
08/08/21 14:16:45 61SNR030_230_0326
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)µµ(#'# 
#
)
µ
µ µ
µ
DTC 1303: DTC 1305:
YES
NO YES
NO
23-32423-324Navigation System
DTC Troubleshooting (cont’d)
GPS Receiver Error 2
Gyro Error 2: ECU Temp XX °C
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside and away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside and away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
 Do this test only when the dash temperature is between 20 °C ( 4 °F) and 70 °C (158 °F).
1. Clear hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.
Is DTC 1303 indicated?
Is DTC 1304 indicated?
08/08/21 14:16:46 61SNR030_230_0327
ProCarManuals.com
DYNOMITE -2009-