error 1 ACURA CSX 2006 Service Repair Manual

¦§ ¦§
(#'# 
#
)(#'# 
#
)
µ
µ
µ
µ µ
µ
µ
µ
DTC 1306: DTC 1307:
YES
NO
YES
NO YES
NO
YES
NO
23-32523-325
Vehicle Speed Pulse
DVD Read Error
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then start the engine.
3. Check for the hard error code (see page 23-273).
Go to step 4.
Intermittent failure, the system is OK at this
time.
4. Drive the vehicle and watch the VSP signal.
Replace the navigation unit (see page 23-355).
Do the symptom troubleshooting for vehicle
position icon constantly leaves road, moves
erratically or is very far from actual position
(see page 23-344). NOTE:
 Check the vehicle battery condition first.
 Check any official Honda service website for more information about the navigation system.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Inspect the navigation DVD for scratches or damage.
1. Turn the ignition switch to ON (II).
Go to DVD screen error messages (see page
23-319).
Go to step 2.
2. Clear the heard error code (see page 23-274).
3. Turn the ignition switch to LOCK (0), then back to ON (II).
4. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.
Is DTC 1306 indicated?
Does t he V SP si gnal change f r om 0 t o 1as you drive? Is there a DVD error message?
Is DTC 1307 indicated?
08/08/21 14:16:46 61SNR030_230_0328
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)(#'# 
#
)
µ
µ µ
µ
DTC 1402: DTC 1409:
YES
NO YES
NO
23-32623-326Navigation System
DTC Troubleshooting (cont’d)
Audio Error 2
Audio Error 9
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Check if the audio unit functions are working
properly. If any problems are found, go to the
applicable troubleshooting in audio section.
Intermittent failure, the system is OK at this
time. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Check the XM error codes (see page 23-194).
If any codes are detected, go to the applicable
troubleshooting in audio (XM) section.
Intermittent failure, the system is OK at this
time.
I s DT C 1402 i nd i cat ed ? I s DT C 1409 i nd i cat ed ?
08/08/21 14:16:46 61SNR030_230_0329
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
(#'# 
#)
´ µ
µ
µ µ
µ
DTC 2607:
YES
NO YES
NO
23-327
NAVIGATION UNIT CONNECTOR E (14P)
GA-NET
BUS
(BLU) GA-NET
BUS
(PNK)
JUMPER WIRE
XM Diag
NOTE: Before you troubleshoot, make sure to follow the
general troubleshooting information (see page 23- 266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back ON (II).
3. Go into the Diagnostic Menu, and select the Self- Diagnosis Mode in the Select Diagnosis Items
menu (see page 23-297).
4. Check the System Links.
Go to step 5.
Intermittent failure, the system is OK at this
time.
5. Turn the ignition switch to LOCK (0). 6. Check for poor connections or loose terminals at
navigation unit connector E (14P), USB adapter unit
connector A (14P), and XM receiver connector A
(14P).
Go to step 7.
Repair poor connections or loose terminals,
and recheck the self-diagnosis mode (see page
23-297).
7. Disconnect navigation unit connector E (14P) and XM receiver connector A (14P).
8. Connect navigation unit connector E (14P) terminals No. 9 and No. 10 with a jumper wire.
(cont’d)
Wire side of female terminals
Is the X M icon red? Ar e t he connect i ons OK ?
08/08/21 14:16:46 61SNR030_230_0330
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#)
µ
µ
µ
µ
µ
µ µ
µ
YES
NO
YES
NO
YES
NO YES
NO
DTC 2609:
23-32923-329
16. Check the System Links.
Go to step 17.
Intermittent failure, the system is OK at this
time.
17. Turn the ignition switch to LOCK (0).
18. Disconnect USB adapter unit connector A (14P), and then turn the ignition switch to ON (II).
19. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
20. Check the System Links.
Go to step 21.
Internal short circuit in the USB adapter
unit.
21. Turn the ignition switch to LOCK (0).
22. Connect USB adapter unit connector A (14P).
23. Disconnect XM receiver connector A (14P), and then turn the ignition switch to ON (II).
24. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
25. Check the System Links.
Replace the navigation unit (see page 23-355).
Replace the XM receiver (see page 23-258). NOTE: Before you troubleshoot, make sure to follow the
general troubleshooting information (see page 23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links, then select the ECU Info.
Intermittent failure, the system is OK at this
time.
Replace the navigation unit (see page 23-355).VRAM Diag
Is the X M icon red?
Is the X M icon red?
Is the X M icon red? I s V -RAM OK i nd i cat ed ?
08/08/21 14:17:48 61SNR030_230_0332
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)(#'# 
#
)
µ
µ µ
µ
µ
µ
DTC 2610: DTC 2701:
YES
NO
YES
NO
YES
NO
23-33023-330Navigation System
DTC Troubleshooting (cont’d)
DRAM Diag
GPS Diag: Antenna
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links, then select the ECU Info.
Intermittent failure, the system is OK at this
time.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside, away from buildings.
 Check for electronic aftermarket accessories (possibly hidden) mounted near the GPS antenna or
the navigation unit.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links, then select the GPS Ant.
Intermittent failure, the system is OK at this
time.
Go to step 5.
5. Turn the ignition switch to LOCK (0).
6. Check for poor connections at navigation unit connector H (2P).
Replace the GPS antenna (see page 23-358).
Repair the poor connection.
I s D-RAM OK i nd i cat ed ?
Is Antenna OK indicated?
I s t he connect i on OK ?
08/08/21 14:17:48 61SNR030_230_0333
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#)(#'# 
#)
µ
µ µ
µ
DTC 2702: DTC 2703:
YES
NO
YES
NO
23-33123-331
GPS Diag: Receiver in Navi ECUAircon Diag
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside, away from buildings.
 Check for electronic aftermarket accessories (possibly hidden) mounted near the GPS antenna or
the navigation unit.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links, then select the GPS Ant.
Intermittent failure, the system is OK at this
time.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Check for B-CAN DTCs and resolve them before troubleshooting.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 DTC 2703 can be stored when the ignition switch is at ACCESSORY (I). With the ignition switch is in
ACCESSORY (I), the climate control unit is turned off
and the navigation unit loses communication and
stores DTCs. Therefore, there is a possibility that the
system is normal even DTC 2703 is stored. Check
system links (see page 23-297) with the engine
running, and if it shows normal, the system is OK at
this time. If not, do this troubleshooting.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Check the System Links.
Go to step 5.
Intermittent failure, the system is OK at this
time.
5. Turn the ignition switch to LOCK (0).
(cont’d)
Is Receiver in Navi ECU OK indicated? Is the Air con icon r ed?
08/08/21 14:17:48 61SNR030_230_0334
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
(#'# 
#)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
DTC 2705:
23-33423-334Navigation System
DTC Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR D (12P)
AC SI
(YEL)
AC CLK
(BLU) AC SO
(RED)
17. Turn the ignition switch to ON (II).
18. Measure the voltage between body ground and
navigation unit connector D (12P) terminals No. 5,
No. 6, and No. 12 individually.
Repair short to power in the wire(s) between
the navigation unit and the climate control unit.
Replace the climate control unit (see page
21-75). NOTE: Before you troubleshoot, make sure to follow the
general troubleshooting information (see page 23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links.
Go to step 5.
Intermittent failure, the system is OK at this
time.
5. Turn the ignition switch to LOCK (0).
6. Connect the HDS to the DLC (see page 23-359).
7. Clear the DTCs with the HDS.
8. Turn the ignition switch to LOCK (0), and then back to ON (II).
9. Check for DTCs with the HDS.
Do the HFL DTC troubleshooting.
Go to step 10.
10. Turn the ignition switch to LOCK (0).
11. Disconnect navigation unit connector B (24P).
12. Disconnect the HandsFr eeLink control unit 28P
connector.HFL Diag
Wire side of female terminals
I s t her e v ol t age abov e 0.2 V ? Is the HF L icon red?
Ar e t her e any H F L DT Cs i nd i cat ed ?
08/08/21 14:17:49 61SNR030_230_0337
ProCarManuals.com
DYNOMITE -2009-

Îµµ
(#'# 
#)
µ
µ µ
µ
Navigation unit
connector Wire color
YES
NO YES
NO
DTC 2706:
23-33623-336Navigation System
DTC Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR B (24P)
17. Check for continuity between navigation unit
connector B (24P) and body ground according to
the table.
B11 GRN
B12 BLK
B23 WHT
B24 RED
Short to body ground in the wires between
the navigation unit and the HandsFreeLink control
unit. Replace the affected shielded harness.
Replace the HandsFreeLink control unit
(see page 23-388). NOTE:
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Do this test only when the passenger’s compartment temperature is between 20 °C ( 4 °F) and 70 °C
(158 °F).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.Gyro Diag: ECU Temp XX °C
Wire side of female terminals
Is there continuity? I s DT C 27 06 i nd i cat ed ?
08/08/21 14:17:49 61SNR030_230_0339
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#)
µ
µ
µ
µ µ
µ
µ
µ
DTC 2707:
YES
NO
YES
NO YES
NO
YES
NO
23-337
MIC Diag
NOTE: Before you troubleshoot, make sure to follow the
general troubleshooting information (see page 23-
266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and select the Self- Diagnosis Mode in the Select Diagnosis items
menu (see page 23-297).
4. Select the System Links.
Go to step 5.
Go to step 8.
5. Turn the ignition switch to LOCK (0).
6. Check for poor connections or loose terminals at the HandsFreeLink control unit 28P connector, the
HFL-navigation microphone 3P connector, and the
navigation unit B (24P) connector.
Go to step 7.
Repair the poor connections or loose
terminals. 7. Check for DTCs with the HDS.
Troubleshoot the indicated DTC.
Replace the HFL-navigation microphone
(see page 23-358).
8. Select the Mic in the System Links.
9. Press the navigation Talk button on the steering wheel switch, then check the Mic Level (see page
23-311).
Intermittent failure, the system is OK at this
time.
Replace the HFL-navigation microphone
(see page 23-358).
Is the Mic icon red?
Ar e t he connect i ons OK ? Is DTC B1775 or B1776 indicated?
I s t he mi cr ophone l ev el OK ?
08/08/21 14:17:50 61SNR030_230_0340
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ µ
µ
µ
µ
µ
µ
GPS icon is white or not shown Voice guidance cannot be heard, is broken
up, or there is static
Diagnostic Test: Self-Diagnosis Mode
YES
NO
YES
NO Diagnostic Test: Self-Diagnosis Mode
YES
NO
YES
NO
YES
NO
23-34123-341
NOTE: Check the vehicle battery condition first.
 With good reception, the icon is normally green.
 Make sure the GPS antenna is plugged in.
 Check for any aftermarket accessories or metallic window tinting that may be interfering with the GPS
signal.
 Make sure the vehicle is parked outside, away from buildings.
 Refer to GPS Information (see page 23-312) for realtime satellite reception display.
1. Check for aftermarket metallic wi ndow tint on the
rear window and electronic aftermarket
accessories (possibly hidden) mounted near the
GPS antenna or the navigation unit.
Remove tint or the accessories, and
recheck.
Go to step 2.
2. Turn the ignition switch to ON (II).
3. Go into the Self-Diagnosis Mode, and use the System Links diagnostic (see page 23- 297) to check
the GPS antenna.
Check for a kinked, crushed, or disconnected
GPS antenna wire. If the icon is still red, replace the
GPS antenna (see page 23-358).
Check that nothing is blocking the GPS
antenna located under the package shelf and
recheck. Substitute a known-good GPS antenna,
and recheck.
 If the symptom is gone, replace the GPS antenna.
 If the symptom is still present, substitute a known-good navigation unit (see page 23- 355),
and recheck. If the symptom is gone, replace the
original navigation unit. NOTE:
 Check the vehicle battery condition first.
 Check the navigation volume level (see Owner’s Manual).
 Check the connectors for poor connections or loose terminals.
 If the Hard Error Code is stored, check the Hard Error Code troubleshooting first.
 Make sure that the correct DVD color and version are installed.
 Inspect the DVD for dirt or damage.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
1. Turn the ignition switch to ON (II).
2. Press the SET-UP button.
3. Check the volume and voice feedback setting for the navigation system in set-up.
Set the voice feedback to ON, and select an
audible level for the volume.
Go to step 4.
4. Check the audio system operation.
Go to step 5.
Troubleshoot audio system.
5. Select the Self-Diagnosis mode.
6. Check for error code to the Error History.
Refer to the Hard Error Code
troubleshooting.
Replace the navigation unit (see page 23-355).
Is there af termarket metallic window tint orel ect r oni c accessor i es?
Is the GPS Ant icon red? Is ei t her set t o OF F ?
Can y ou hear t he aud i o?
Is the Hard Error Code in stored?
08/08/21 14:17:50 61SNR030_230_0344
ProCarManuals.com
DYNOMITE -2009-