light Acura MDX 2003 Owner's Manua

The power window system has a key-
of f delay f unction. The windows will
stilloperateforuptotenminutes
after you turn off the ignition.
Opening either f ront door cancels
the delay function. You must turn
the ignition switch ON (II) again
bef ore you can operate the windows.
If the driver’s window runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
window, remove the obstacle, then
use the window switch again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it. If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction will be disabled. The
power window system needs to be
reset af ter reconnecting the battery
or installing the f use. You should do
the f ollowing.
Any impact due to road conditions
may cause the auto reverse f unction
work unexpectedly on the closing
window. If it happens f requently,
there is a problem with your power
window system. You should have
your car inspected by your dealer.
You can still close the window by
pulling back on the window switch
lightly and hold it. If the power windows do not operate
properly af ter resetting, have your
vehicle checked by a Acura dealer.Start the engine. Push down on
the driver’s window switch until
the window is f ully open.
Pull back on the driver’s window
switch to close the window
completely, then hold the switch
f or a second or two more.
1.
2.
Power Windows
Inst rument s and Cont rols
Auto Reverse
113

The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this sensing.
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
Mirrors
Inst rument s and Cont rols115
SENSOR
AUTO SWITCH
INDICATOR

Adjust the outside mirrors with the
adjustment switch on the lef t side of
the dashboard:Turn the ignition switch ON (II).
Move the selector switch to L
(driver’s side) or R (passenger’s
side). Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment switch so you can’t
move a mirror out of position by
accidentally bumping the switch.With the selector switch in the
center (of f ) position, the passenger’s
side mirror will pivot downward
slightly when you shif t the
transmission into reverse. This gives
you a better view of the side of the
vehicle while parallel parking. The
mirror returns to its original position
when you take the transmission out
of reverse.
1.
2. 3.
4.
Touring ModelAdjusting the Power Mirrors
Mirrors
Inst rument s and Cont rols116
SELECTOR SWITCH
ADJUSTMENT SWITCH

To apply the parking brake, push the
parking brake pedal down with your
f oot. To release the parking brake,
push on the pedal again. The parking
brake light on the instrument panel
should go out when the parking
brake is f ully released with the
engine running. (see page .)
The outside mirrors are heated to re-
move fog and frost. With the ignition
switchON(II),turnontheheaters
by pressing the button. The light in
the button comes on as a reminder.
Press the button again to turn the
heaters off.
69
Parking Brake
Mirrors, Parking Brake
Inst rument s and Cont rols117
HEATED MIRROR BUTTON
PARKING BRAKE PEDAL
Driving the vehicle with the parking
brake applied can damage the rear
brakes and axles.

Turn the ignition switch ON (II).
You cannot add a new driving
position in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
Seat and outside mirror positions, f or
two dif f erent drivers or driving
conditions,canbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Memory 1 or
Memory 2). Store a driving position as explained
in this section only when the vehicle
is parked.
Adjust the seat to a comfortable
position (see page ). Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
Your Acura has a memory f eature
f or the driver’s seat and outside
mirror positions.
Adjust the outside mirrors f or best
visibility (see page ).3.
1.
2.
116
101
Touring Model
St oring a Driving Posit ion in Memory
Driving Posit ion Memory Syst em
Inst rument s and Cont rols118
MEMO BUTTON

Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.Not pressing a memory button
within 5 seconds.
You can select memorized positions
as f ollows.Make sure the parking brake is set
and the shif t lever is in Park.
Readjusting the seat position.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.The system will move the seat and
outside mirrors to the memorized
positions. The indicator light in the
selected memory button will f lash
during movement. When the
adjustments are complete, you will
hear two beeps and the indicator
light will remain on.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected. 1.
2.
CONT INUED
Select ing a Memorized Posit ion
Driving Posit ion Memory Syst em
Inst rument s and Cont rols119
MEMORY BUTTONS

Press any button on the control
panel: MEMO, 1 or 2.
To stop the system’s automatic ad-
justment;
Push any of the adjustment
switches f or the seat.
Shif t out of Park.
Adjust the outside mirrors. If desired, you can use the
adjustment switches to change the
positions of the seat or outside
mirrors af ter they are in their
memorized position. If you change
the memorized position, the
indicator light in the memory button
will go out. To keep this driving
position f or later use, you must store
it in the driving position memory.
Driving Posit ion Memory Syst em
Inst rument s and Cont rols120

CONT INUED
Make sure you put the sun visor
back in place when you are getting
into or out of the vehicle. Do not use
the sun visor extension over the rear
view mirror.Touseavanitymirroronthebackof
the sun visor, pull up the cover.
The light beside the mirror comes
on only when the parking lights or
headlights are on.Your vehicle has three accessory
power sockets. The f ront accessory
power socket is located under the
audio system. The second socket is
located in the center console
compartment. The rear socket is
behind the third seat on the driver’s
side.
Sun Visor, Vanity Mirror, Accessory Power Sockets
Inst rument s and Cont rols
Vanity Mirror
Accessory Power Sockets
125
FRONT
(Without Rear Entertainment System)

These sockets are intended to supply
power f or 12 volt DC accessories
that are rated 120 watts or less (10
amps). To use an accessory power socket,
the ignition switch must be in
ACCESSORY (I) or ON (II). Tousethesocketintheconsole
compartment, pull the cover up.None of the sockets will power an
automotive type cigarette lighter
element. The rear socket has a maximum
power rating of 120 watts (10 amps.) When both the front and console
sockets are being used, the
combined power rating of both
accessories should be 120 watts or
less (10 amps).
A ccessory Power Socket s
Inst rument s and Cont rols126
FRONT
(With Rear Entertainment System)

When this switch is in the OFF
position:None of the lights come on when a
door or the tailgate is opened.
The individual map lights in the
f ront can be turned on and of f with
the switches next to the lights. The individual map lights in the
f ront come on when any door or
thetailgateisopened.Whenthe
doors and the tailgate are closed,
eachlightcanbeturnedonandoff
with the switch next to the light.
When the switch is in the Door
Activated position:
The cargo area light (3rd row)
cannot be turned on. The individual map lights in the
secondrowcomeonwhenany
door or the tailgate is opened.
When the doors and the tailgate
are closed, each light can be
turned on and off with the switch
next to the light.
The light control switch controls the
interior lights: the individual map
lights by the sun visors, the
individual map lights above the
second row passengers, and the
cargo area light. This switch has
three positions: OFF, Door Activated,
and ON. The individual map lights in the
second row cannot be turned on.
L ight Control Switch
Interior Lights
Inst rument s and Cont rols128
ON
DOOR
ACTIVATED
POSITION OFF