ground clearance ACURA NSX 1997 Service Repair Manual

3-13
TDesign Specifications
(cont’d)
ITEMMETRICENGLISH
DIMENSIONSOverall length
Overall width
Overall height
Wheelbase
Track F/R
Ground clearance
Seating capacity4,425 mm 174.2 in
1,810 mm 71.3 in
1,170 mm 46.1 in
2,530 mm 99.6 in
1,510/1,540 mm 59.4/60.6 in
130 mm 5.1 in
2
WEIGHT (USA)
Single plate dry, diaphragm spring
Torque converter
239 cm
237.0 sq in
CLUTCHClutch M/T
A/T
Clutch lining area M/T
Gross Vehicle Weight Rating (GVWR)
NOTES
Gear reduction/DENSO
1.4 kW
12 V
30 seconds
Counterclockwise as viewed
from gear end
4.75 kg 10.47 lbs
ENGINEWater cooled, 4-stroke DOHC VTEC
gasoline engine
90 °V6-cylinder, transverse
93.0 x 78.0 mm 3.66 x 3.07 in
90.0 x 78.0 mm 3.54 x 3.07 in
3,179 cm
3(cc) 194 cu in
2,977 cm3(cc) 182 cu in
10.2
Belt driven DOHC
Forced and wet sump
Premium UNLEADED grade gasoline
with 91 Pump Octane Number
or higher
STARTERType/Make
Normal output
Nominal voltage
Hour rating
Direction of rotation
Weight
WEIGHT (CANADA)Gross Vehicle Weight Rating (GVWR)
Synchronized 6 speed forward 1 reverse
Electronically controlled
4-speed forward automatic 1 reverse
Direct 1 : 1Transmission M/T
A/T
Primary reduction
Manual AutomaticType
3.066 2.611
1.956 1.551
1.428 1.025
1.125 0.684
0.914—
0.717—
3.186 1.909Gear ratio 1st
2nd
3rd
4th
5th
6th
Reverse
Single helical gear
4.062 4.428
TRANSMISSION
Final reduction Gear type
Gear ratio
Type
Cylinder arrangement
Bore and strokeC32B1 engine
C30A1 engine
DisplacementC32B1 engine
C30A1 engine
Compression ratio
Valve train
Lubrication system
Fuel required
M/T 1,630 kg 3,593 lbs
A/T 1,655 kg 3,649 lbs
*04-NSX (61SW004)SEC03(01-16) 9/22/04 1:49 PM Page 3-13
ProCarManuals.com

Towing

If the vehicle needs to be towed, call a professional tow-

ing service. Never tow the vehicle behind another vehi-

cle with just a rope or chain. It is very dangerous.

There are three widely used methods of towing a vehicle.

Flat-bed Equipment — The operator loads the vehicle on

the back of a truck. This is the only recommended way

of towing the NSX & NSX-T.

Wheel Lift Equipment — The tow truck driver uses two

pivoting arms which go under the tires (front or rear)

and lift them off the ground. The other two wheels

remain on the ground. This towing method is not rec-

ommended. Because of the NSX & NSX-T's low ground

clearance, the body can be damaged going over large

bumps or up inclines.

Sling-type Equipment — The tow truck uses metal

chains with hooks on the ends. These hooks go around

parts of the frame or suspension and the cables lift that

end of the vehicle off the ground. Damage to the vehi-

cle's suspension and body is almost certain if this

method of towing is attempted.

If the NSX & NSX-T cannot be towed by flat-bed, it

should be towed with the rear wheels off the ground. If,

due to damage, the vehicle must be towed with the rear

wheels on the ground, do the following:

Manual Transmission

• Release the parking brake

• Shift the transmission to Neutral

Automatic Transmission

• Release the parking brake

• Start the engine

• Shift to position, then to position

• Turn off the engine

NOTICE:

• Improper towing preparation will damage the trans-

mission. Follow the above procedure exactly. The car

must be towed on a flat bed if the engine will not

start or the transmission will not shift.

• It is best to tow the vehicle no farther than 50 miles

(80 km), and keep the speed below 35 mph (55 km/h).

• Trying to lift or tow the vehicle by the bumpers will

cause serious damage. The bumpers are not

designed to support the vehicle's weight.ProCarManuals.com

Wheel Alignment

Height

NSX/NSX-T four wheel alignment requires the use of equipment designed specifically for four wheel independent

suspensions and capable of immediate feedback.

NOTE: For proper inspection/adjustment of the wheel alignment, check and adjust the following before checking

the alignment.

• Check that the suspension is not modified.

• Check the tire size and tire pressure.

• Check the runout of the wheels and tires.

• Check the suspension ball joints. (Hold a wheel with your hands, then move the wheel up and down and right

and left to check for wobbling.)

• Check the height of each suspension (see below).

Standard value

Front:

Ground clearance to the center of the lower

control arm bolt
Rear:

Ground clearance to the center of the toe con-

trol arm bolt

Height inspection:

• Before checking for the height, bounce the vehicle up and down several times before measuring.

• Check the height with the vehicle empty, parked on a level surface, with properly inflated tires (tread wear indicators

must not be showing). If the height is out of specification, load or unload the vehicle as necessary.ProCarManuals.com