display Acura ZDX 2012 Owner's Manual

MODE－To switch between the
category mode and channel mode,
push the interface selector down to
display AUDIO MENU, then turn the
interface dial to select Mode, and
press ENTER on the interface
selector.
Turn the interface dial to select CH
or CAT, then press ENTER on the
interface selector. Move the interface
selector up to go back.
You can also switch the mode by
pressing the TITLE side of the
SCAN/TITLE bar for 3 seconds.
In the category mode, such as Jazz,
Rock, Classical, etc., you can
navigate through all of the channels
within that category. In the channel
mode, you can select all of the
available channels. Each time you press and release the
TITLE side of the bar, the display
changes in the following sequence:
CATEGORY NAME, NAME (artist
name), TITLE (music title), and
CHANNEL NAME (channel name).
On the screen, you will see the
selected CHANNEL (number),
CATEGORY, NAME (artist name),
and TITLE (music title).
You may experience periods when
XM Radio does not transmit the
artist's name and song title
information. If this happens, there is
nothing wrong with your system.
TUNE
－Press either side of the
TUNE bar to change channel
selections. Press the
side of the
bar for higher numbered channels
and the
side for lower numbered
channels. You can also change
channels with the interface selector. Push it down to select AUDIO
MENU. Then turn the interface dial
to select TUNE and press ENTER on
the interface selector. Turn the
interface dial to exit the tune mode
and press ENTER on the interface
dial.
CHANNEL LIST
－Push down the
interface selector to select AUDIO
MENU, then turn the interface dial
to select Channel List and press
ENTER on the selector. Turn the
interface dial to select a channel,
then press ENTER to set your
selection.
CATEGORY (－ or＋)－ Press
either side of the bar to select
another category.
CONTINUED
Playing the XM
®Radio (Models with navigation system)
293
Features
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

SCAN－The scan function gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the channels within that
category are scanned. To activate
SCAN, press the SCAN side of the
SCAN/TITLE bar. You will see
SCAN on the screen and display.
The system plays each channel in
numerical order for a few seconds,
then selects the next channel. When
you hear a channel you want to
continue listening to, press the
SCAN side of the bar to cancel.
CHANNEL SCAN －This function
samples all channels. Push down the
interface selector to select AUDIO
MENU, then turn the interface dial
to select Channel Scan and press
ENTER on the interface selector.
CATEGORY SCAN －This function
samples the stations in the selected
category. Push down the interface
selector to select AUDIO MENU,
then turn the interface dial to select
Category Scan and press ENTER on
the interface selector.
Preset －You can store up to 12
preset channels using the six preset
buttons. Each button stores one
channel from the XM1 band and one
channel from the XM2 band.
To store a channel:
1. Press the
button. Either
XM1 or XM2 will show on the
display.
2. Use the tune, channel list, or scan function to tune to a desired
channel.
Playing the XM
®Radio (Models with navigation system)
29409/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

3. Pick the preset button you want forthat channel. Press and hold the
preset button until you hear a
beep. You can also pick the
number with the interface dial.
Select your desired number and
press and hold ENTER on the
interface selector.
4. Repeat steps 2 and 3 to store the first six channels.
5. Press the
button or scroll
up again. The other XM band will
be shown. Store the next six
channels using steps 2 and 3.
Once a channel is stored, press
and release the proper preset
button to tune to it.
XM Radio Display Messages
‘‘ OFF AIR ’’－ The channel
currently selected is no longer
broadcasting. ‘‘LOADING
’’－ XM is loading the
audio or program information.
‘‘UPDATING ’’－ The encryption
code is being updated. Wait until the
encryption code is fully updated.
Channels 0 and 1 should still work
normally.
‘‘NO SIGNAL ’’－ The signal is
currently too weak. Move the vehicle
to an area away from tall buildings,
and with an unobstructed view of the
southern horizon.
‘‘
’’ － The selected channel
number does not exist, or is not part
of your subscription, or this channel
has no artist or title information at
this time.
‘‘CHECK ANTENNA ’’－ There is a
problem with the XM antenna.
Please consult your dealer.
CONTINUED
Playing the XM
®Radio (Models with navigation system)
295
Features
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

There may be other geographic
situations that could affect XM Radio
reception.As required by the FCC:Changes or modifications not expressly
approved by the party responsible forcompliance could void the user's
authority to operate the equipment. Note Function
U.S. models onlyThis function stores the sound
content played on the selected XM
satellite radio station with the
channel, category, name, and title
information.
To activate this function, press and
hold the
button for about 3
seconds while a song or passage
which you want to store is playing.
You can record for up to 10 seconds.
To stop recording, press the AM/FM
button,button, or another
function button (DISC, HDD, USB/
AUX).
Once you store the recorded sound
file, you can replay it and confirm the
information. The system can store up
to 30 sound files. If you continue to
store more files, the oldest one will
be deleted each time you add new
file.
To replay and see the stored file,
press the AUDIO button to select the
audio display on the navigation
screen.
Push down the interface selector to
display the audio menu. Turn the
interface dial to select Note, then
press ENTER.
NOTE ICON
CONTINUED
Playing the XM
®Radio (Models with navigation system)
297
Features
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Turn the selector dial to select a
sound file, then press ENTER. The
display shows the category, name
and title information of the selected
file and plays the recorded portion of
the song.
To delete a file, push the interface
selector to the right to select
‘‘DELETE. ’’Select ‘‘Delete All ’’or
‘‘ Delete Selected Item, ’’then press
ENTER on the interface selector. Receiving XM Radio Service
If your XM Radio service has expired
or you purchased your vehicle from a
previous owner, you can listen to a
sampling of the broadcasts available
on XM Radio. With the power mode
in ACCESSORY or ON, press the
button. A variety of music
types and styles will play.
Your vehicle has the engine start/
stop button instead of an ignition
switch. For more information on how
to select the power mode, see page
194. If you decide to purchase XM radio
service, contact XM
ꭂRadio at
www.
xmradio.com,
or at 1-800-852-9696. In
Canada, contact XM Canada
ꭂat
www.xmradio.ca,
or call
1-877-209-0079. You will need to give
them your radio I.D. number and
your credit card number. To get your
radio I.D. number, press and release
the
side of the TUNE bar until ‘‘0’’
appears in the display. Your I.D. will
appear in the display.
After you have registered with XM
Radio, keep your audio system in the
satellite radio mode while you wait
for activation. This should take about
30 minutes.
SOUND FILE RECORDED DATE
Playing the XM
®Radio (Models with navigation system)
29809/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

While waiting for activation, make
sure your vehicle remains in an open
area with good reception. Once your
audio system is activated, CAT
(category) or CH (channel) will
appear in the display, and you’ll be
able to listen to XM Radio
broadcasts. XM Radio will continue
to send an activation signal to your
vehicle for at least 12 hours from the
activation request. If the service has
not been activated after 36 hours,
contact XM Radio. In Canada, contact
XM CANADA
ꭂ.
Playing the XM
®Radio (Models with navigation system)
299
Features
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

SCAN/TITLE BAR VOL/ꂻ(VOLUME/POWER) KNOB
DISC BUTTON
TUNE BAR PRESET BUTTONS
SKIP BAR
AUDIO BUTTON CATEGORY BAR NAVIGATION SCREEN
DISPLAY
DISC SLOT
EJECT BUTTON
Playing a Disc (Models with navigation system)30009/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Your vehicle’s audio system has an
internal disc player. To operate the
disc player, the power mode must be
ACCESSORY or ON.
Your vehicle has the engine start/
stop button instead of an ignition
switch. For more information on how
to select the power mode, see page
194.
The DISC player can play these disc
formats:●CD (CD-DA, CD-TEXT)●CD-R/CD-RW (MP3, WMA, AAC)●DVD-A●DVD-R/DVD-RW (MP3, WMA,
AAC)
If you have a disc that is a
combination of CD-DA tracks and
MP3/WMA/AAC files, you can
choose the format to listen to by
pressing and holding the DISC
button until you hear a beep. The disc packages or jackets should
have one of these marks.
The disc player can also play MP3,
WMA, or AAC format saved on CD-
R/RW or DVD-R/RW (see page 306).
NOTE:
If a file on an MP3, WMA or AAC
disc is protected by digital rights
management (DRM), the audio
system skips to the next file.
Depending on the software the files
were made with, it may not be
possible to play some files, or display
some text data.
DVD-A discs not meeting DVD
verification standards may not be
playable.
Video CDs and DVD-V format discs
will not work in this unit.
Some CD-DA and CD-ROM mixed
discs are not playable.
You cannot load and play 3-inch (8-
cm) discs in this system.
CONTINUED
Playing a Disc (Models with navigation system)
301
Features
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

It is possible to select up to 999 files
for inclusion in CD-Rs and CD-RWs,
and up to 3,500 files for inclusion in
DVD-Rs and DVD-RWs.Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.
Manufactured under license under
U.S. Patentꭨ’s: 5,451,942; 5,956,674;
5,974,380; 5,978,762; 6,487,535 &
other U.S. and worldwide patents
issued & pending. DTS and DTS
Digital Surround are registered
trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc.
© 1996-2008 DTS, Inc. All Rights
Reserved. To Load a Disc
Insert a disc about halfway into the
disc slot. The drive will pull the disc
in the rest of the way to play it. You
operate the disc player with the same
controls used for the radio. The
number of the current track is shown
in the display. When playing a disc in
MP3, WMA or AAC, the numbers of
the current folder and file are shown.
The system will continuously play a
disc until you change modes.
For information on how to handle
and protect compact discs, see page
365.
To Play a Disc
Select the disc player by pressing the
DISC button. The system will begin
playing the last selected track on the
disc. You will see the current track
position highlighted.
Title information will be displayed by
a list when the information is found
in the Gracenote
ꭂAlbum Info
(Gracenote
ꭂMedia Database) on the
built-in hard disk drive. When you
play a CD recorded with text data,
you will see the genre, artist name,
album and track name on the screen.
When you play MP3/WMA/AAC
discs, you will see the genre, artist
name, album name and track name
on the screen. If the disc was not
recorded with this information, it will
not be displayed.
Playing a Disc (Models with navigation system)30209/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Each time you press the TITLE side
of the SCAN/TITLE bar, the display
changes from artist name to album
name, to track name and then to
normal display that shows the track
number and the elapsed time. When
playing a disc in MP3/WMA/AAC,
the display mode changes from
folder name, to file name, to artist
tag, to album tag, to track tag, and
then to normal display.To Change Tracks
Each time you press and release the
side of the skip bar, the player
skips forward to the beginning of the
next track. Press and release the
side of the skip bar to skip backward
to the beginning of the current track.
Press the
side again to skip to the
previous track. To move rapidly
within a track, press and hold either
side of the skip bar.
When you insert a CD for the first
time, the system automatically starts
recording to the hard disc. For
information on recording from music
CDs, see page 315. To Choose a Track
You can also choose a track directly
from a track list. If there are no track
names, you will see
‘‘No Title’’
displayed. Turn the interface dial to
select the desired track, then press
ENTER on the interface selector.
TRACK LIST
CONTINUED
Playing a Disc (Models with navigation system)
303
Features
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu