hood open Acura ZDX 2012 Owner's Manual

When you lock the doors, some
exterior lights blink and the system
beeps once. If no exterior lights blink
and/or no beeper sounds, check to
see if the tailgate or hood is open.
To change the‘‘KEYLESS ACCESS
LIGHT FLASH ’’setting, see page
120.
To change the ‘‘KEYLESS ACCESS
BEEP ’’setting, see page 121.
Within 2 seconds of pressing the
door lock button to lock the doors or
locking the doors with remote, pull
the handle to make sure the doors
are actually locked. The door unlock
sensors will not operate for about 2
seconds after the doors are locked. The door lock button does not work
if:
●The remote is not within the
operating range.●Any door is open.●The power mode is not set to
VEHICLE OFF (LOCK).●The remote is in the keyless
access slot.●The remote is too close to the
vehicle.●The remote battery is dead.●The vehicle battery is dead.
Door Lock PreventionIf you open the driver's door, pull its
lock tab rearward on the door, and
shut it when the remote is inside the
vehicle, the driver's door will unlock.
Make sure you carry the remote with
you when you lock the doors.
This function is also activated on the
front passenger's door. If you open
the front passenger's door, and shut
it after pulling its lock tab rearward
when the remote is inside the
vehicle, all doors will unlock.
CONTINUED
Keyless Access System
187
Instruments and Controls
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Before closing the tailgate, make
sure the remote is not inside the
vehicle.
If you close the tailgate when the
remote is inside the vehicle, and all
the doors are locked, the system
beeps, and all the doors unlock.
Keep the tailgate closed at all times
while driving to avoid damaging the
tailgate, and to prevent exhaust gas
from getting into the interior. See
Carbon Monoxide Hazardon page
58. Keyless Access Remote
LOCK
－Press this button once to
lock all doors and the tailgate. Some
exterior lights will flash. When you
push the LOCK button twice within 5
seconds, you will hear a beep to
verify that the doors and the tailgate
are locked and the security system is
set. You cannot lock the doors or the
tailgate if any door or the tailgate is
open, if the remote is in the keyless
access remote slot, or if the power
mode is in any position except the
VEHICLE OFF (LOCK).
When you cannot set the security
system because the tailgate or hood
is open, no exterior light blinks and/
or no beeper sounds.
LED
UNLOCK
BUTTON
PANIC
BUTTON LOCK
BUTTON
TAILGATE
BUTTON
CONTINUED
Keyless Access System
189
Instruments and Controls
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

The security system helps to protect
your vehicle and valuables from
theft. The horn sounds and a
combination of headlights, position
lights, side marker lights and
taillights flashes if someone attempts
to break into your vehicle or remove
the audio unit. This alarm continues
for 2 minutes, then the system
resets. To reset an activated system
before the 2 minutes have elapsed,
unlock the driver's door with the key
or the remote transmitter/keyless
access remote.
The security system automatically
sets 15 seconds after you lock the
doors, hood, and the tailgate. For the
system to activate, you must lock the
doors and the tailgate from the
outside with the key, driver's lock
tab, door lock master switch, or
remote transmitter/keyless access
remote. The security system
indicator on the instrument panel
starts blinking immediately to show
you the system is setting itself.
Once the security system is set,
opening any door, the tailgate, or the
hood without using the key or the
remote transmitter/keyless access
remote, will cause it to alarm. It also
alarms if the audio unit is removed
from the dashboard or the wiring is
cut.The security system will not set if the
hood, tailgate, or any door is not fully
closed. If the system will not set,
check that the doors, the tailgate and
the hood are fully closed.
Do not attempt to alter this system or
add other devices to it.
SECURITY SYSTEM INDICATOR
Security System37809/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Before you begin driving your
vehicle, you should know what
gasoline to use and how to check the
levels of important fluids. You also
need to know how to properly store
cargo or packages. The information
in this section will help you. If you
plan to add any accessories to your
vehicle, please read the information
in this section first.Break-in Period
...........................
454
Fuel Recommendation
................
454
Service Station Procedures
.........
455
Refueling
.................................
455
Tighten Fuel Cap Message
.....
456
Opening and Closing the
Hood
...................................
457
Oil Check
................................
458
Engine Coolant Check
............
459
Fuel Economy
.............................
460
Accessories and
Modifications
..........................
463
Carrying Cargo
...........................
465
Before Driving
453
Before Driving
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

The message should go off after
several days of normal driving once
you tighten or replace the fuel fill
cap. To scroll to another message,
press the INFO button. The
‘‘TIGHTEN FUEL CAP ’’message
will appear each time you restart the
engine until the system turns the
message off.
If the system still detects a leak in
the vehicle's evaporative emissions
system, the malfunction indicator
lamp (MIL) comes on. If the fuel fill
cap was not already tightened, turn
the engine off, and check or
retighten the fuel fill cap until it
clicks at least once. The MIL should
go off after several days of normal
driving once the cap is tightened or
replaced. If the MIL does not go off,
have your vehicle inspected by a
dealer. For more information, see
page 593. Opening and Closing the Hood
1. Park the vehicle, and set the
parking brake. Pull the hood
release handle located under the
lower left corner of the dashboard.
The hood will pop up slightly.
2. Put your fingers under the frontedge of the hood near the center.
Slide your hand to your left until
you feel the hood latch handle.
Push this handle up until it
releases the hood. Lift up the
hood.
If the hood latch handle moves stiffly,
or if you can open the hood without
lifting the handle, the mechanism
should be cleaned and lubricated.
HOOD RELEASE HANDLE
LATCH
CONTINUED
Service Station Procedures
457
Before Driving
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Synthetic Oil
You may use a synthetic motor oil if
it meets the same requirements
given for a conventional motor oil: it
displays the API Certification Seal
and it is the proper weight. You must
follow the oil and filter change
intervals shown on the multi-
information display.
Engine Oil Additives
Your vehicle does not require any oil
additives. Additives may adversely
affect the engine or transmission
performance and durability.Changing the Engine Oil and
Filter
Always change the oil and filter
according to the maintenance
messages shown on the multi-
information display. The oil and filter
collect contaminants that can
damage your engine if they are not
removed regularly.
Changing the oil and filter requires
special tools and access from
underneath the vehicle. The vehicle
should be raised on a service station-
type hydraulic lift for this service.
Unless you have the knowledge and
proper equipment, you should have
this maintenance done by a skilled
mechanic.
1. Run the engine until it reaches
normal operating temperature,
then shut it off.
2. Open the hood, and remove theengine oil fill cap. Remove the oil
drain bolt and washer from the
bottom of the engine. Drain the oil
into an appropriate container.
WASHER
DRAIN BOLT
Adding Engine Oil, Changing the Engine Oil and Filter54609/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Headlight Aiming
The headlights were properly aimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustments should be done by your
dealer or another qualified
technician.
Low/High Beam Headlight Bulb
Replacement
The low/high beam headlight bulbs
are a type of high voltage discharge
tube. High voltage can remain in the
circuit even with the light switch off
and the key removed (or the vehicle
is in VEHICLE OFF (LOCK) mode
on models with keyless access
system). Because of this, you should
not attempt to examine or change a
low/high beam headlight bulb
yourself. If a low/high beam
headlight bulb fails, take the vehicle
to your dealer to have it replaced.Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
1. Open the hood.
2. Remove the front bulkhead cover
and engine compartment covers
(see page 544).
3. Remove the socket by turning it one-quarter turn counterclockwise.
4. Pull the bulb straight out of its socket.
5. Push the new bulb straight intothe socket until it bottoms.
6. Insert the socket back into the headlight assembly. Turn it
clockwise to lock it in place.
7. Turn on the lights to make sure the new bulb is working.
FRONT TURN SIGNAL/PARKING LIGHT
SOCKETBULB
SIDE MARKER LIGHT
SOCKET BULB
CONTINUED
Lights
555
Maintenance
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Replacing a Daytime Running
Light Bulb1. Open the hood.To change the bulb on the driver's
side, remove the clips by pushing
the center of the clips. Lift the
grommet over the stud bolt and
rotate the heat shield
counterclockwise. To change the bulb on the
passenger's side, remove the
power steering fluid reservoir by
pulling it out of its stay.
2. Remove the front bulkhead cover and engine compartment covers
(see page 544).
3. Remove the electrical connectorfrom the bulb by pushing on the
tab and pulling the connector
down. 4. Remove the bulb by turning it one-
quarter turn counterclockwise.
5. Install the new bulb into the hole, and turn it one-quarter turn
clockwise to lock it in place.
6. Push the electrical connector back onto the bulb. Make sure it is on
all the way.
7. Test the lights to make sure the new bulb is working.
8. Reinstall the front bulkhead cover and engine compartment covers.
On the driver's sideReinstall the heat shield.On the passenger's sideReinstall the power steering fluid
reservoir.
CLIP HEAT SHIELD
GROMMET
STUD BOLT
CONNECTOR BULB
Lights55609/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Check the condition of the wiper
blades at least every 6 months.
Replace them if you find signs of
cracking in the rubber, and areas
that are getting hard or if they leave
streaks and unwiped areas when
used.
To replace a wiper blade:
1. Raise each wiper arm off thewindshield, lifting the driver's side
first, then the passenger's side.Do not open the hood when the wiper
arms are raised, or you will damage the
hood and the wiper arms.
2. Disconnect the blade assemblyfrom the wiper arm:
●Put a cloth on the edge of the
lock tab to prevent scratches,
then push up on the lock tab
carefully with a flat-tip
screwdriver.●Slide the blade assembly toward
the wiper arm until it releases
from the wiper arm.
WIPER ARMS
LOCK TAB
Wiper Blades56409/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu

Although this seems like a simple
procedure, you should take several
precautions.
A battery can explode if you do
not follow the correct
procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.
You cannot start your vehicle by
pushing or pulling it.
To Jump Start Your Vehicle:1. Open the hood, and check the physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or frozen, do not try
jump starting until it thaws.If a battery sits in extreme cold, the
electrolyte inside can freeze. Attempting
to jump start with a frozen battery can
cause it to rupture.
2. Turn off all the electricalaccessories: climate control, audio
system, lights, etc. Put the
transmission in Park, and set the
parking brake.
The numbers in the illustration show
you the order to connect the jumper
cables.
3. Connect one jumper cable to the
positive (＋ ) terminal on your
vehicle's battery. Connect the
other end to the positive (＋ )
terminal on the booster battery.BOOSTER BATTERY
CONTINUED
Jump Starting
587
Taking Care of the Unexpected
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu