lock Alfa Romeo 4C 2021 Instructieboek (in Dutch)

KNOWING YOUR CAR
26
❒ introducing the hand in the opening
cleared by the flap, find out the pressure-
fit protective cap 2 fig. 26 and remove it;
❒ in the luggage compartment find the
supplied screwdriver and insert it in the
operating hole;
❒ rotate the screw as shown in fig. 26
until you hear the lock click;
❒ refit the protective cap 2.
25A0L0142
The procedure must be carried out on
both headlights.
For versions with Bi-LED headlights to
avoid dazzling the drivers on the other
side of the road, you need to cover areas
of the headlight according to the Highway
Code of the country you are travelling in.
26A0L0141
Adapt both headlights as shown in fig. 27.
27A0L0145

KNOWING THE INSTRUMENT PANEL TOOLS
30
CONTROL PANEL AND ON-BOARD INSTRUMENTS
DISPLAY WITH METRIC UNITS
1. Engine coolant gauge 2. Clock 3. Tachometer 4. Mode/gear engaged indicator 5. Gear Shift Indicator 6. External temperature
7. Fuel level gauge (the triangle on the right side of the symbol indicates the side of the car with the fuel filler)
8. Area dedicated to the display of the digital warning light related to the displayed message 9. Trip odometer 10. Speedometer
11. “Alfa DNA” system driving mode 12. Messages or information on display 13. Total odometer.
29A0L0118

31
DISPLAY WITH IMPERIAL UNITS
1. Engine coolant gauge 2. Clock 3. Tachometer 4. Mode/gear engaged indicator 5. Gear Shift Indicator 6. External temperature
7. Fuel level gauge (the triangle on the right side of the






symbol indicates the side of the car with the fuel filler)
8. Area dedicated to the display of the digital warning light related to the displayed message 9. Trip odometer 10. Speedometer
11. “Alfa DNA” system driving mode 12. Messages or information on display 13. Total odometer.
30A0L0129

35
Warning lights on panelMeaning What to do
Drive very carefully to the nearest
Alfa Romeo Dealership
to have the system inspected immediately.
20) 21)
Contact Alfa Romeo Authorized Services if you wish to
permanently deactivate the S.B.R. (Seat Belt Reminder)
system buzzer.
The system can be reactivated using the Set-up Menu.
EBD FAULT
The simultaneous switching on of the x(red) and >
(amber) warning lights with the engine on, indicates either
a failure of the EBD system or that the system is not
available. In this case, the rear wheels may suddenly lock
and the vehicle may swerve when braking sharply.
The display shows the dedicated message.
AIRBAG FAILURE
When the key is turned to MAR, the warning light switches
on, but it should switch off after a few seconds.
The warning light on indicates an airbag system failure.
The display shows the dedicated message.
SEAT BELTS NOT FASTENED
(where provided)
The warning light remains on steadily with the car at
stationary and the driver’s seat belt not correctly
fastened.
The warning light will turn on flashing together with the
buzzer when, with car moving, driver’s seat belt are not
fastened correctly.

SAFETY
50
ACTIVE SAFETY SYSTEMS
ABS SYSTEM
This system, which is an integral part of
the braking system, prevents one or
more wheels from locking and slipping in
all road surface conditions, irrespective
of the intensity of the braking action,
ensuring that the vehicle can be
controlled even during emergency
braking and optimising stopping
distances.
System intervention
The driver can feel that the ABS system
has come into action because the brake
pedal pulsates slightly and the system
gets noisier: this is entirely normal with
the system operating.
30) 31) 32) 33) 34) 35) 36)
ASR (AntiSlip Regulation) SYSTEM
37) 38) 39)
This is an integral part of the ESC system
and automatically operates in the event
of one or both drive wheels slipping, loss
of grip on wet roads (aquaplaning) and
acceleration on slippery, snowy or icy
roads, etc.
System intervention
The system intervenes on the engine
power and the brakes.
It is indicated by the flashing of the
warning light on the instrument panel,
to inform the driver that the vehicle is
in critical stability and grip conditions.
HBA (Hydraulic Brake Assist) SYSTEM
40) 41) 42)
The HBA system is designed to improve
the car’s braking capacity during
emergency braking: the HBA system
therefore completes the ABS system.
Maximum assistance from the HBA
system is obtained by continuously
pressing the brake pedal very quickly.
EBD SYSTEM
The EBD system is an integral part of the
ESC system and intervenes during
braking, distributing the brake force
optimally between front and rear wheels.
This guarantees greater braking stability
for the car, preventing sudden locking of
the rear wheels and the consequent
instability of the car.
DTC (Drag Torque Control) SYSTEM
This is an integral part of the ABS
system and intervenes in the case of
sudden downshifting, or during braking
when the ABS intervenes, restoring
torque to the engine and thus preventing
excessive drag at the drive wheels, which
may lead the wheels to lock and a loss of
car stability, above all in low-grip
conditions.

51
ESC SYSTEM
The ESC system improves the
directional control and stability of the
car in various driving conditions.
The ESC system corrects the car’s
understeer and oversteer, distributing
the brake force on the appropriate
wheels. The torque supplied by the
engine can also be reduced in order to
maintain control of the vehicle.
25) 26) 27) 28) 29)
The ESC system comprises the active
safety systems such as: ABS, EBD, ASR,
HILL HOLDER, etc.
The ESC system switches on
automatically when the engine is started
and cannot be switched off.
System intervention
This is indicated by the flashing of the
warning light on the instrument panel, to
inform the driver that the car is in critical
stability and grip conditions.
CBC
(Cornering Braking Control) SYSTEM
This system acts when braking on
corners, optimising the distribution of
brake pressure on the four wheels: the
system prevents the wheels on the
inside of the corner (less affected by the
weight of the car) from locking, ensuring
better stability and direction for the car.
HILL HOLDER SYSTEM
This is an integral part of the ESC system
and facilitates starting on uphill or
downhill slopes by operating the brakes:
IMPORTANT The Hill Holder system is
not a parking brake, therefore do not
leave the car without activating the
handbrake, switched the engine off and
engaged first gear, so that the car is
parked in safety conditions (for further
information read paragraph
“When parked” in the chapter “Starting
and driving”).
IMPORTANT There may be situations on
small gradients (less than 8%), with car
laden, in which the Hill Holder system
may not activate thus causing a slight
reversing motion and increasing the risk
of collision with another vehicle or
object. The driver is, in any case,
responsible for safe driving.
“ELECTRONIC Q2” SYSTEM (“E-Q2”)
The DTC system prevents the drive
wheels from possibly locking, which
could happen, for example, if the
accelerator pedal is released suddenly or
in the case of a sudden downshifting in
conditions of poor grip.
In this conditions, the engine braking
effect could cause the drive wheels to
slip, resulting in a loss of vehicle stability.
In these situations, the DTC system
intervenes, restoring torque to the
engine in order to conserve vehicle
stability and increase vehicle safety.

57
SEAT BELTS
All vehicle seats are equipped with seat
belts with three anchor points and a
retractor.
The retractor mechanism operates
locking the belt in the event of sharp
braking or strong deceleration due to an
impact. This allows the belt strap to slide
freely and to adapt to the body of the
occupant. In the event of an accident, the
belt will lock reducing the risk of impact
inside the passenger compartment and
of being projected outside the vehicle.
The driver is responsible for respecting,
and ensuring that all the other occupants
of the vehicle also respect, the local laws
in force in relation to the use of the seat
belts.
Always fasten the seat belts before
setting off.
USING THE SEAT BELTS
The belt should be worn keeping the
torso straight and rested against the
backrest. To fasten the seat belts, hold
the tongue 1 fig. 33 and insert it into the
buckle 2, until it clicks into place.On removal of the belt, if it jams, let it
rewind for a short stretch, then pull it out
again without jerking.
To unfasten the seat belts, press button
3 and guide the seat belt with your hand
while it is rewinding, to prevent it from
twisting.
52))
The retractor may lock when the vehicle
is parked on a steep slope: this is
perfectly normal. Furthermore, the reel
mechanism locks the belt if it is pulled
sharply or in the event of sudden braking,
collisions and high-speed bends.
33A0L0050
GENERAL INSTRUCTIONS FOR USING
THE SEAT BELTS
Comply with (and make sure all car
passengers follow) the local laws in force
regarding the use of seat belts. Always
fasten the seat belts before setting off.
Seat belts must also be worn by
pregnant women: the risk of injury in the
event of an accident is reduced for them
and the unborn child if they are wearing a
seat belt.
Pregnant women must position the lower
part of the belt very low down so that it
passes over the pelvis and under the
abdomen fig. 34.
The belt must not be twisted.
The upper part must pass over the
shoulder and cross the chest diagonally.
34A0L0052

69
PARKING THE VEHICLE
Always remove the ignition key when
leaving the car.
When parking and leaving the car,
proceed as follows:
❒ engage the gear (on a slope, engage
first gear if the vehicle is facing uphill or
reverse if it is facing downhill) and leave
the wheels steered;
❒ stop the engine and engage the
handbrake.
Block the wheels with a wedge or a stone
if the car is parked on a steep slope.
Wait until the indication of the gear
engaged disappears on the display
before releasing the brake pedal.
76)
IMPORTANT NEVER leave the car with
the transmission in neutral.
HANDBRAKE
To engage the handbrake, pull lever
1 fig. 42 upwards until the car is secured.
When the handbrake is engaged and the
ignition key is at MAR, the xwarning
light will switch on in the instrument
panel.
To release the handbrake, raise the lever
1 slightly, hold down button 2 and lower
the lever.
The xwarning light on the instrument
panel turns off.
Four or five clicks are generally enough
when the car is on level ground, while ten
or eleven may be required if the car is on
a steep slope and laden.
77)
IMPORTANT Carry out these
manoeuvres with the brake pedal
pressed.
42A0L0066
76)Never leave children unattended in
the vehicle. Always remove the key from
the ignition device when leaving the
vehicle and take it with you.
77)The car must be braked after a few
clicks of the handbrake: if this is not so,
contact the dedicated Alfa Romeo
Dealership to have it adjusted. Always
park the car safely as indicated by the
Highway Code and as described above.
IMPORTANT

STARTING AND DRIVING
74
The car always starts in neutral. When
1st gear is requested, the system forces
the selection of AUTO mode.
IMPORTANT If 10 seconds elapse with
the ignition key in the MAR position and
the display does not show the gear
engaged, turn the key to the STOP
position, wait for the display to go out
and then repeat the manoeuvre.
If the fault persists, contact a dedicated
Alfa Romeo Dealership.
ACOUSTIC SIGNAL
For safety reasons, there is a buzzer
warning when parking the car with the
gearbox in neutral (N) (the warning is
heard when the ignition key is turned to
the STOP position).
With the vehicle stationary, the engine
started and (1st) or (R) engaged, the
system activates the buzzer and
automatically put the gearbox in neutral
(N) when:
❒ the accelerator and/or the brake
pedal are not operated for at least 3
minutes;
❒ the brake pedal is pressed for longer
than 10 minutes;❒ the driver’s door is opened and the
accelerator pedal or the brake pedal are
not operated for at least 1.5 seconds;
❒ a fault is detected in the gearbox.
PARKING THE CAR
When parking and leaving the car,
proceed as follows:
❒ engage the gear (on a slope, engage
first gear if the vehicle is facing uphill or
reverse if it is facing downhill) and leave
the wheels steered;
❒ stop the engine and engage the
handbrake.
Block the wheels with a wedge or a stone
if the car is parked on a steep slope.
Wait until the indication of the gear
engaged disappears on the display
before releasing the brake pedal.
IMPORTANT: NEVER leave the car with
the transmission in neutral.
IMPORTANT NOTES
❒ With car stationary and gear engaged,
always keep the brake pedal pressed
until you decide to set off, then release
the brake and accelerate gradually.
❒ During prolonged stops with the
engine running, it is advisable to keep the
gearbox in neutral (N).❒ In order to safeguard the efficiency of
the clutch, do not use the accelerator to
keep the car stationary (e.g. when
stopped on an incline). Clutch overheating
could damage it:
use the brake pedal instead or the
handbrake and only press the accelerator
pedal when you wish to set off.
❒ If, with reverse gear (R) engaged, you
have to engage 1st gear or vice versa,
only do this when the car is completely
stationary and with the brake pedal
pressed.
❒ Although it is strongly discouraged, if
you are going downhill and for unknown
reasons you let the car move forward
with the gearbox in neutral (N), when
there is a request to engage a gear the
system will automatically engage the
best gear in relation to the speed of the
actual to allow the correct transmission
of the drive torque to the wheels;.

REPLACING AN
EXTERIOR BULB
FRONT LIGHT CLUSTERS
These contain the bulbs for the side
lights/daytime running lights (DRL),
dipped beam headlights, main beam
headlights and direction indicators.
The bulbs are arranged as follows
in fig. 55:
1 Side lights/daytime running lights
2 Dipped/main beam headlights
3 Direction indicators.
55A0L0091
To replace the bulbs for the dipped and
main beam headlights and for the
direction indicators open the
corresponding protective flaps on the
inner wheel arch
fig. 56 that can be located by steering
the wheel completely.
1 direction indicator bulb protective
flap
2 dipped/main beam headlight bulb
protective flap.
SIDE LIGHTS/DAYTIME
RUNNING LIGHTS (DRL)
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
56A0L0092
DIPPED/MAIN BEAM HEADLIGHTS
To replace the bulb, proceed as follows:
❒ steer the wheel completely;
❒ open the protective flap
2 fig. 56 by rotating the fixing screw;
❒ take out the electric connector
1 fig. 57 and then rotate the bulb holder 2
clockwise and remove it;
❒ remove the bulb and replace it;
❒ refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector 1;
❒ close the protective flap 2 fig. 56.
57A0L0093
IN AN EMERGENCY
84