ACURA CSX 2006 Service Repair Manual

µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-208PGM-FI System
DLC Circuit Troubleshooting (cont’d)
ECM/PCM CONNECTOR A (44P)
CANL (RED)
38. Check for continuity between ECM/PCM connectorterminal A37 and body ground.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Repair open in the wire between the ECM/
PCM (A37) and DLC terminal No. 14. 39. Try to start the engine.
Go to the F-CAN circuit troubleshooting
(see page 11-191).
Go to step 40.
40. Turn the ignition switch to LOCK (0).
41. Check the No. 2 IG MAIN (50 A) fuse in the under- hood fuse/relay box.
Repair open in the wire between the No. 2 IG
MAIN (50 A) fuse and the ignition switch. If the wire
isOK,gotostep42.
Repair short in the wire between the No. 2 IG
MAIN (50 A) fuse and the under-hood fuse/relay
box.AlsoreplacetheNo.2IGMAIN(50A)fuse.
Terminal side of female terminals
Is there continuity? Does t he engi ne st ar t and i d l e smoot hl y ?
IsthefuseOK?
08/08/21 14:21:56 61SNR030_110_0208
ProCarManuals.com
DYNOMITE -2009-

Î

´
´
µ
µ
µ
µ
YES
NO
YES
NO
11-209
C PGM-FI MAIN RELAY 1 4P CONNECTOR
B
B
42. Inspect the No. 19 FI MAIN (15 A) fuse in the under- hood fuse/relay box.
Go to step 49.
Go to step 43.
43. Remove the blown No. 19 FI MAIN (15 A) fuse from the under-hood fuse/relay box.
44. Remove PGM-FI main relay 1 (C) from the under- hood fuse/relay box. 45. Check for continuity between body ground and
PGM-FI main relay 1 4P connector terminals No. 1
and No. 3 individually.
Replace the under-hood fuse/relay box
(see page 22-65). Also replace the No. 19 FI MAIN
(15 A) fuse.
Go to step 46.
(cont’d)
Terminal side of female terminals
IsthefuseOK? Is there continuity?
08/08/21 14:21:56 61SNR030_110_0209
ProCarManuals.com
DYNOMITE -2009-


µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-210PGM-FI System
DLC Circuit Troubleshooting (cont’d)
IGP
PGM-FI MAIN RELAY 1 4P CONNECTOR
IGP
PGM-FI MAIN RELAY 1 4P CONNECTOR
46. Disconnect each of the parts or connectors these
parts, one at a time, while checking for continuity
between PGM-FI main relay 1 4P connector
terminal No. 2 and body ground.
 PGM-FI main relay 2 (FUEL PUMP)
 ECM/PCM connector A (44P)
 Each injector 2P connector
 Camshaft position (CMP) sensor B 3P connector
 Crankshaft position (CKP) sensor 3P connector
 Ignition coil relay
 Electronic throttle control system (ETCS) control relay
Replace the part that made the short to body
ground go away when disconnected. Reconnect all
connectors, then update the ECM/PCM if it does not
have the latest software (see page 11-227), or
substitute a known-good ECM/PCM (see page 11-7),
then recheck. If the symptom/indication goes away
with a known-good ECM/PCM, replace the original
ECM/PCM (see page 11-228). Also replace the
No.19FIMAIN(15A)fuse.
Go to step 47.
47. Disconnect the connectors from these parts:  PGM-FI main relay 2 (FUEL PUMP)
 ECM/PCM connector A (44P)
Injectors
 Camshaft position (CMP) sensor B
 Crankshaft position (CKP) sensor
 Ignition coil relay
 Electronic throttle control system (ETCS) controlrelay 48. Check for continuity between PGM-FI main relay 1
4P connector terminal No. 2 and body ground.
Repair short in the wire between PGM-FI
main relay 1 and each part. Also replace the No. 19
FI MAIN (15 A) fuse.
Replace PGM-FI main relay 1. Also replace the
No.19FIMAIN(15A)fuse.
49. Inspect the No. 2 FUEL PUMP (15 A) fuse in the under-dash fuse/relay box.
Go to step 61.
Go to step 50.
50. Remove the blown No. 2 FUEL PUMP (15 A) fuse from the under-dash fuse/relay box.
Terminal side of female terminals Terminal side of female terminals
Does cont i nui t y go aw ay w hen one of t he abov e
component s i s d i sconnect ed ? Is there continuity?
IsthefuseOK?
08/08/21 14:21:57 61SNR030_110_0210
ProCarManuals.com
DYNOMITE -2009-

Î
Î
µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
11-211
A
PGM-FI MAIN RELAY 2 (FUEL PUMP) 4P CONNECTOR IG1 ECM/PCM CONNECTOR C (44P)
IG1 (BLK/GRN)
51. Remove PGM-FI main relay 2 (FUEL PUMP) (A)from the under-dash fuse/relay box.
52. Test PGM-FI main relay 2 (FUEL PUMP) (see page 22-70).
Go to step 53.
Replace PGM-FI main relay 2 (FUEL PUMP).
Also replace the No. 2 FUEL PUMP (15 A) fuse.
53. Check for continuity between PGM-FI main relay 2 (FUEL PUMP) 4P connector terminal No. 1 and
body ground.
Go to step 54.
Go to step 57. 54. Jump the SCS line with the HDS.
55. Disconnect ECM/PCM connector C (44P).
56. Check for continuity between ECM/PCM connector
terminal C36 and body ground.
Repair short in the wire between the No. 2
FUEL PUMP (15 A) fuse and the ECM/PCM (C36),
between the No. 2 FUEL PUMP (15 A) fuse and
PGM-FI main relay 2 (FUEL PUMP), or between the
No. 2 FUEL PUMP (15 A) fuse and the immobilizer
control unit. Also replace the No. 2 FUEL PUMP
(15 A) fuse.
Replace the No. 2 FUEL PUMP (15 A) fuse,
and update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
57. Remove the rear seat cushion (see page 20-131).
58. Remove the rear floor upper cross-member and the access panel from the floor (see page 11-334).
59. Disconnect the fuel pump 4P connector.
(cont’d)
Terminal side of female terminals Terminal side of female terminals
Is the relay OK ?
Is there continuity? Is there continuity?
08/08/21 14:23:31 61SNR030_110_0211
ProCarManuals.com
DYNOMITE -2009-




µ
µ µ
µ
YES
NO
YES
NO
11-212PGM-FI System
DLC Circuit Troubleshooting (cont’d)
FUEL PUMP 4P CONNECTOR
FUEL PUMP
(GRN)
ECM/PCM CONNECTOR C (44P)
IG1 (BLK/GRN)
60. Check for continuity between fuel pump 4Pconnector terminal No. 2 and body ground.
Repair short in the wire between the fuel
pump and PGM-FI main relay 2 (FUEL PUMP). Also
replace the No. 2 FUEL PUMP (15 A) fuse.
Check the fuel pump, and replace it if needed
(see page 11-338). Also replace the No. 2 FUEL
PUMP (15 A) fuse. 61. Jump the SCS line with the HDS.
62. Disconnect ECM/PCM connectors A (44P) and C
(44P).
63. Turn the ignition switch to ON (II).
64. Measure the voltage between ECM/PCM connector terminal C36 and body ground.
Go to step 65.
Repair open in the wire between the No. 2
FUEL PUMP (15 A) fuse and the ECM/PCM (C36).
Wire side of female terminals
Terminal side of female terminals
Is there continuity?Is there battery voltage?
08/08/21 14:23:31 61SNR030_110_0212
ProCarManuals.com
DYNOMITE -2009-


Î 

´
µ
µ µ
µ
YES
NO YES
NO
11-213
ECM/PCM CONNECTOR A (44P)
MRLY (GRN)
C B
PGM-FI MAIN RELAY 1 4P CONNECTOR
65. Measure the voltage between ECM/PCM connector
terminal A6 and body ground.
Go to step 70.
Go to step 66.
66. Turn the ignition switch to LOCK (0).
67. Remove PGM-FI main relay 1 (C) from the under- hood fuse/relay box. 68. Measure the voltage between PGM-FI main relay 1
4P connector terminal No. 3 and body ground.
Go to step 69.
Replace the under-hood fuse/relay box
(see page 22-65).
(cont’d)
Terminal side of female terminals Terminal side of female terminals
Is there battery voltage?
Is there battery voltage?
08/08/21 14:23:32 61SNR030_110_0213
ProCarManuals.com
DYNOMITE -2009-


Î


´
µ
µ
µ
µ
YES
NO
YES
NO
11-214PGM-FI System
DLC Circuit Troubleshooting (cont’d)
MRLY (GRN)
ECM/PCM
CONNECTOR A (44P) MRLY
PGM-FI MAIN RELAY 1 4P CONNECTOR
C
B
PGM-FI MAIN RELAY 1 4P CONNECTOR
69. Check for continuity between PGM-FI main relay 1
4P connector terminal No. 4 and ECM/PCM
connector terminal A6.
Test PGM-FI main relay 1 (see page 22-70). If
the relay is OK, update the ECM/PCM if it does not
have the latest software (see page 11-227), or
substitute a known-good ECM/PCM (see page 11-7),
then recheck. If the symptom/indication goes away
with a known-good ECM/PCM, replace the original
ECM/PCM (see page 11-228).
Repair open in the wire between the ECM/
PCM (A6) and PGM-FI main relay 1. 70. Turn the ignition switch to LOCK (0).
71. Remove PGM-FI main relay 1 (C) from the under-
hood fuse/relay box.
72. Measure the voltage between PGM-FI main relay 1 4P connector terminal No. 1 and body ground.
Go to step 73.
Replace the under-hood fuse/relay box
(see page 22-65).
Terminal side of female terminals
Terminal side of female terminals
Terminal side of female terminals
Is there continuity?Is there battery voltage?
08/08/21 14:23:32 61SNR030_110_0214
ProCarManuals.com
DYNOMITE -2009-


Î
µ
µ
µ
µ µ
µ
YES
NO
YES
NO
YES
NO
11-215
IGP
ECM/PCM CONNECTOR A (44P) IGP (ORN) PGM-FI MAIN RELAY 1 4P CONNECTOR
ECM/PCM CONNECTORS
B(44P) PG2 (BLK/RED)
PG1 (BLK)
C (44P)
LG2
(BRN/YEL)
LG1
(BRN/YEL) PGMETCS
(BLK)(BLK)*
*: ’07-09 models
73. Check for continuity between PGM-FI main relay 1 4P connector terminal No. 2 and ECM/PCM
connector terminal A8.
Go to step 74.
Repair open in the wire between the ECM/
PCM (A8) and PGM-FI main relay 1.
74. Test PGM-FI main relay 1 (see page 22-70).
Go to step 75.
Replace PGM-FI main relay 1. 75. Disconnect ECM/PCM connector B (44P).
76. Check for continuity between body ground and
ECM/PCM connector terminals B1, B36, C2, C40,
and C44 individually.
Go to step 77.
Repair open in the wire between the ECM/
PCM (B1, B36, C2, C40, C44) and G101; A/T model
(see page 22-16), M/T model (see page 22-18).
(cont’d)
Terminal side of female terminals
Terminal side of
female terminals
Terminal side of female terminals
Is there continuity?Is PGM-FI main relay 1 OK ? Is there continuity?
08/08/21 14:23:33 61SNR030_110_0215
ProCarManuals.com
DYNOMITE -2009-



µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
11-216PGM-FI System
DLC Circuit Troubleshooting (cont’d)
ECM/PCM CONNECTOR C (44P)
VCC1 (YEL/RED) ECM/PCM CONNECTOR B (44P)
VCC2 (YEL/BLU) (YEL)*
*:K20Z3engine
77. Check for continuity between ECM/PCM connector terminal C13 and body ground.
Go to step 78.
Go to step 79.
78. Continue to check for continuity between ECM/PCM connector terminal C13 and body ground, while
disconnecting these connectors, one at a time:
 MAP sensor 3P connector
 Output shaft (countershaft) speed sensor 3P connector (K20Z2 engine)
Replace the part that caused an open when it
was disconnected.
Repair short in the wire between the ECM/
PCM (C13) and the MAP sensor or the output shaft
(countershaft) speed sensor (K20Z2 engine). 79. Check for continuity between ECM/PCM connector
terminal B18 and body ground.
Go to step 80.
Go to step 81.
80. Continue to check for continuity between ECM/PCM connector terminal B18 and body ground, while
disconnecting these connectors, one at a time:
 EGR valve 6P connector (K20Z2 engine)
 Input shaft (mainshaft) speed sensor 3P connector (K20Z2 engine)
 Output shaft (countershaft) speed sensor 3P connector (K20Z3 engine)
Replace the part that caused an open when it
was disconnected.
Repair short in the wire between the ECM/
PCM (B18) and the EGR valve (K20Z2 engine), the
input shaft (mainshaft) speed sensor (K20Z2
engine) or the output shaft (countershaft) speed
sensor (K20Z3 engine).
Terminal side of female terminals Terminal side of female terminals
Is there continuity?
Does cont i nui t y go aw ay w hen one of t he abov ecomponent s i s d i sconnect ed ? Is there continuity?
Does cont i nui t y go aw ay w hen one of t he abov epar t s i s d i sconnect ed ?
08/08/21 14:23:33 61SNR030_110_0216
ProCarManuals.com
DYNOMITE -2009-



µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
11-217
ECM/PCM CONNECTOR C (44P)
VCC3 (BLU) ECM/PCM CONNECTOR A (44P)
VCC4
(BRN)
81. Check for continuity between ECM/PCM connectorterminal C12 and body ground.
Go to step 82.
Go to step 83.
82. Continue to check for continuity between ECM/PCM connector terminal C12 and body ground, while
disconnecting the throttle body 6P connector.
Repair short in the wire between the ECM/
PCM (C12) and the throttle body.
Replace the throttle body; K20Z2 engine
(see page 11-348), K20Z3 engine (see page 11-349). 83. Check for continuity between ECM/PCM connector
terminal A25 and body ground.
Go to step 84.
Go to step 85.
84. Continue to check for continuity between ECM/PCM connector terminal A25 and body ground, while
disconnecting the APP sensor 6P connector.
Repair short in the wire between the ECM/
PCM (A25) and the APP sensor.
Replace the accelerator pedal module; K20Z2
engine (see page 11-269), K20Z3 engine (see page
11-270).
(cont’d)
Terminal side of female terminals Terminal side of female terminals
Is there continuity?
Is there continuity? Is there continuity?
Is there continuity?
08/08/21 14:23:34 61SNR030_110_0217
ProCarManuals.com
DYNOMITE -2009-