Alfa Romeo GT 2006 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
49
Headlamp washers (fig. 65)
These come into operation when the
windscreen washer is turned on with the
dipped/main beam headlights on.
IMPORTANTOn certain versions
when the headlamp washer is operating,
the climate control system automatically
engages inside air re-circulation, to pre-
vent the smell of liquid detergent from
entering the passenger compartment.CRUISE CONTROL
GENERAL
The speed regulator (CRUISE CON-
TROL), with electronic control, makes it
possible to drive the car at the required
speed without pressing the accelerator
pedal. This reduces driving fatigue during
long journeys because the speed memo-
rised is automatically maintained.
IMPORTANTThe device can only be
engaged at speeds between 30 and 190
km/h.
fig. 65
A0A0704bCruise Control must be ac-
tivated only when the
route and traffic allow a
constant speed for a sufficiently
long distance completely safely.
The device is disengaged automatically
in any of the following cases:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR, MSR or VDC system cuts in;
– with Selespeed transmission if a gear
is changed;
– inadvertently moving the Selespeed
gear control lever to N.
CONTROLS(fig. 66)
Cruise Control is controlled by the
ON/OFFknurled ring (A), by the +/–
ring(B) and by the RESbutton (C).
Ring (A) has two positions:
–OFFin this position the device is
deactivated;
fig. 66
A0A0077b

GETTING TO KNOW YOUR CAR
50
TO MEMORISE THE SPEED
Move the ring (A) to ONand take the
car to the required speed normally. Turn
the ring (B) to (+) for at least three sec-
onds, then release it. The car speed is
memorised and it is therefore possible to
release the accelerator pedal.
The car will continue to travel at the
memorised constant speed until one of
the following conditions takes place:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR, MSR or VDC system cuts
in;
– with Selespeed transmission if a gear
is changed;
– inadvertent movement of the
Selespeed gear control lever to position
N.
IMPORTANTIn the case of need
(when overtaking for instance) accelera-
tion is possible simply pressing the accel-
erator pedal; later, releasing the accelera-
tor pedal, the car will return to the speed
memorised previously.
TO RESET THE
MEMORISED SPEED
If the device has been disengaged for
example pressing the brake or clutch
pedal, the memorised speed can be reset
as follows:
– accelerate gradually until reaching a
speed approaching the one memorised;
– engage the gear selected at the time
of speed memorising (4th, 5th or 6th
speed);
– press the RESbutton (C).
TO INCREASE THE
MEMORISED SPEED
The speed memorised can be increased
in two ways:
1) pressing the accelerator and then
memorising the new speed reached (turn-
ing the ring to (B) for more than three sec-
onds);
or
2) momentaneously turning the ring (B)
to (+): each pulse of the ring will corre-
spond to a slight increase in speed (about
1.5 km/h) while pressing continuously
will correspond to a continuous speed
increase. Releasing the ring (B) the new
speed will be memorised automatically. –ONis the normal operating position
of the device. When the ring (A) is in this
position, the warning light
Üon the
instrument cluster turns on.
Ring (B) serves for memorising and
maintaining the car sped or for increasing
or lowering the speed memorised.
Turn the ring (B) to (+) to memorise
the speed reached or increase the speed
memorised.
Turn the ring (B) to (–) to lower the
speed memorised.
Each time the ring is actuated (B) the
speed increases or lowers by about 1.5
km/h.
Keeping the ring turned the speed
changes continuously. The new speed
reached will be maintained automatically.
TheRESbutton (C) resets the memo-
rised speed.
IMPORTANTTurning the ignition key
toSTOPor the ring (A) to OFF, the
speed memorised is cleared and the sys-
tem is switched off.

GETTING TO KNOW YOUR CAR
51
TO REDUCE THE
MEMORISED SPEED
The speed memorised can be reduced in
two ways:
1) disengaging the device (for instance
pressing the brake pedal) and then mem-
orising the new speed (turning the ring
(B) to (+) for at least three seconds);
2) keeping the ring pressed (B) at (–)
until reaching the new speed which will be
memorised automatically.The device may only be engaged in in
4th, 5th or 6th gear, depending on the
speed of the car. Travelling downhill with
the device engaged the car speed may
increase more than the memorised one,
due to the change in the engine load.
The ring (A) may be left constantly at
ONwithout damaging the device. You
are, however, advised to switch the device
off when not in use, turning the ring to
OFF, to avoid memorising speeds by
accident. It is advisable to engage the cruise con-
trol only when the conditions of the traffic
or roads so permit under completely safe
conditions, i.e.: straight and dry roads,
dual carriage ways or motorways, flowing
traffic and smooth road surface. Do not
engage the device in town or in heavy
traffic conditions.When travelling with the
cruise control on, do not
move the gearshift lever to
neutral and do not move the Sele-
speed selector to N.
Cruise control may only
be engaged at speeds be-
tween 30 and 190 km/h.
If the device is faulty or
not working, turn the ring
(A) to OFF and contact Al-
fa Romeo Authorised Services af-
ter checking that the protection
fuse is intact.
ESETTING THE MEMORISED
SPEED
The memorised speed is automatically
reset turning off the engine or moving the
ring (A) to OFF.

GETTING TO KNOW YOUR CAR
52
DASHBOARD
(As concerns right-hand drive versions, see dashboard and instrument panel controls described in the dedicated paragraph at the end of this
manual)
1. Side swivel air vents - 2. Fixed side window air vents - 3. Outer light control lever - 4. Speedometer with mileage recorder and trip recorder and headlamp
aiming display - 5. Fuel level gauge with reserve warning light - 6. Multifunction display - 7. Engine coolant fluid temperature gauge - 8. Rev counter - 9. Tail-
gate release button - 10. Car holder (for versions/markets where applicable) - 11. Radio (for versions/markets where applicable) - 12. Centre swivel air
vents - 13. Fixed upper vent - 14. Glass holder (for versions/markets where applicable) - 15. Fog lamp button - 16. Hazard warning light switch - 17. Rear
fog guard button - 18. Passenger’s front Air bag - 19. Glove-box - 20. Door locking button - 21. Controls for heating, ventilation and climate control - 22. Cig-
ar lighter/ashtray cover - 23. Temperature sensor - 24. Windscreen wiper control lever - 25. Ignition key and switch - 26. Horn - 27. Steering wheel lock-
ing/release lever - 28. Driver’s front Air bag - 29. Set of controls: trip meter reset, headlamp aiming device, trip computer - 30. Bonnet opening lever.
fig. 67
A0A0618b

GETTING TO KNOW YOUR CAR
53
A. Fuel level gauge with reserve warning
light - B. Engine coolant fluid temperature
gauge with maximum temperature warn-
ing light - C. Speedometer - D. Odometer
display (mileage recorder, trip recorder with
headlamp position display - E. Reconfigu-
rable multifunction display - F. Rev counter
Petrol version
A. Fuel level gauge with reserve warning
light - B. Engine coolant fluid temperature
gauge with maximum temperature warn-
ing light - C. Speedometer - D. Odometer
display (mileage recorder, trip meter with
headlamp position display) - E. Reconfigu-
rable multifunction display - F. Rev counter
INSTRUMENT PANEL
Petrol versions
fig. 68 - 1.8 T. SPARK - 2.0 JTS
fig. 69 - 2.0 JTS Selespeed
A0A0656b
A0A0655b

GETTING TO KNOW YOUR CAR
54
fig. 70 - 3.2 V6
fig. 71 - JTD 16V
Petrol versions
A.Fuel level gauge with reserve warning
light - B.Engine coolant fluid temperature
gauge with maximum temperature warn-
ing light - C.Speedometer - D.Odometer
display (mileage recorder, trip meter with
headlamp position display) - E.Reconfigu-
rable multifunction display - F.Rev counter
Diesel versions
A. Fuel level gauge with reserve warning
light - B. Engine coolant fluid temperature
gauge with maximum temperature warn-
ing light - C. Speedometer - D. Odometer
display (mileage recorder, trip meter with
headlamp position display) - E. Reconfigu-
rable multifunction display - F. Rev counter
A0A0687b
A0A0657b

GETTING TO KNOW YOUR CAR
55
SPEEDOMETER
The gauge (A-fig. 72) indicates the
car speed.
MILEAGE RECORDER
Odometer display (B-fig. 72) with
double meter (total and trip) and head-
lamp position display.
The display shows:
– the mileage on the first line (6 fig-
ures)
– the trip meter on the second line (4
figures)
– the position relating to the headlamp
aiming device.
To reset the trip meter, keep the button
(A-fig. 73) on the plate at the side of
the steering column pressed a few sec-
onds.
IMPORTANTIf the battery is discon-
nected the trip meter reading is not
stored.
REV COUNTER (fig. 74-75)
The danger zone (red) indicates exces-
sively high engine speed. Do not drive for
long periods with the pointer in this area.
IMPORTANTThe electronic injection
control system gradually shuts off the flow
of fuel when the engine is “over-revving”
resulting in a gradual loss of engine power.
When the engine is idling, the rev counter
may indicate a gradual or sudden highering
of the speed, this is normal as it takes place
during normal operation, for example when
engaging the climate control system or the
fan. In particular a slow change in the speed
preserves the battery charge.
fig. 73
A0A0082b
fig. 74 - Petrol versions
A0A0666b
fig. 75 - JTD 16Vversions
A0A0667bfig. 72
A0A0665b

GETTING TO KNOW YOUR CAR
56
FUEL LEVEL GAUGE WITH
RESERVE INDICATOR
This shows the amount of fuel left in the
fuel tank.
The warning light
K(A-fig. 76) turns
on to indicate that approx. 7 litres of fuel
are left in the tank.
IMPORTANTUnder certain conditions
(heavy slopes, for instance), the reading on
the gauge may differ from the actual
amount of fuel in the tank and changes in
level may be indicated late.
This condition falls within the operation
logics of the electronic control circuit to
avoid highly unstable readings due to
swaying of the fuel when travelling.
IMPORTANTRefuelling shall always be
performed with engine off and ignition key
atSTOP. If the engine is off but the key is
atMAR, a wrong fuel level could tem-
porarily be indicated. This is due to the inter-
nal system control logic and cannot be con-
sidered as a system malfunctioning.
ENGINE COOLANT FLUID
TEMPERATURE GAUGE WITH
MAXIMUM TEMPERATURE
WARNING LIGHT
This shows the temperature of the
engine coolant fluid and begins when the
fluid temperature exceeds approx. 50°C.
Normally the pointer should be towards
the middle of the scale. If the pointer
reaches the higher temperatures of the
scale (red area) the request for vehicle
performance should be decreased.
The turning on of the
u(B-fig. 76)
warning light(on some versions together
with the message shown on the reconfig-
urablemultifunction display) indicates that
the coolant fluid temperature is too high;
in this case, stop the engine and contact
Alfa Romeo Authorised Services.IMPORTANTThe temperature of the
engine coolant may rise towards the max-
imum values (red zone) when the vehicle
is driven at low speeds, especially when
the ambient air temperature is high. In
this case it is advisable to stop the vehicle
and switch off the engine for a few min-
utes, after which the journey can be
resumed, preferably at a higher speed.
fig. 76
A0A0668b

GETTING TO KNOW YOUR CAR
57
DIGITAL MULTIFUNCTION DISPLAY (where fitted)
The digital multifunction display shows the following: clock, outside temperature, buzzer setting (buzzer on/off), rheostat (light adjust-
ment), condition of the inertial fuel cut-off switch (FPS on).
CONTROL BUTTONS (fig. 75)
To make use of the information the digital display (with the ignition key at MAR) is able to give, you should firstly familiarise with the
control buttons on the plate at the side of the steering column, using them as described in the following paragraphs. Before doing anything
at all, you are advised to read this chapter in full.
To increase the value displayed
To decrease the value displayed Press for less than 1 second (pulse), indicated with
Qin the following
descriptions, to access the various adjustments
Press for more than 2 seconds, indicated with
Rin the following descrip-
tions, to confirm the choice required and return to the previous display
IMPORTANTWhen the standard display is on (clock + outside temperatured), pressing
âorãthe lighting adjustment rheostat is turned on.
fig. 75
A0A0022b

GETTING TO KNOW YOUR CAR
58
CLOCK(fig. 76)
Adjusting the hours
Press the MODE button in
Q, the hours
will flash. Set the hour required using button
âorã.
Every press on the button will increase
by one unit.
Keeping the button pressed obtains auto-
matic fast increase or decrease.
When you are near the value required,
release the control and complete adjust-
ment with single presses.
Then press the MODE button in
Rto
store.
fig. 76Adjusting the minutes
Press the MODE button twice in
Q,
the minutes will flash. Set the minutes
required using button
âorã.
Every press on the button will increase
by one unit.
Keeping the button pressed obtains auto-
matic fast increase or decrease.
When you are near the value required,
release the control and complete adjust-
ment with single presses.
Then press the MODE button in
Rto
store.
OUTSIDE TEMPERATURE (fig. 76)
Outside temperature can be viewed on
the display lower side, under the hour indi-
cation. When the outside temperature is
below or 3° C, the indicator starts flashing
together with the buzzer, to warn the dri-
ver about the possible presence of ice on
the road. The acoustic signal lasts about 2
seconds, while the outside temperature
indicator flashes for about 10 seconds.
The signal of possible presence of ice on
the road is repeated only if the outside
temperature is over 6° C and then reach-
es again 3° C.
A0A0009b
fig. 77
A0A0083b
BUZZER(fig. 77-78)
The buzzer which accompanies the con-
trols may be activated (
ON) or deactivat-
ed (
OFF); proceed as follows:
Press the MODE button 3 times in
Q,
then use button
âorã, to turn the
buzzer on or off.
The press the MODE button in
Rto
store the condition chosen.
clock and outside temperature display
buzzer activated display (ON)