battery ASTON MARTIN V8 VANTAGE 2010 Workshop Manual

Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-16 Workshop Manual May 2007
6. Install the fuel tank drainage adaptor (see Fig. 1).
7. Connect the external pipe to a fuel recovery unit.
Recover the fuel in accordance with the recovery unit
instructions.
8. Remove the recovery unit and fuel tank drainage adaptor.
9. Disconnect fuel tank sender unit multiplug (see Fig. 2).
10. Release fuel tank sender assembly from bracket. 11. Remove fuel tank sender unit (see Fig. 3).
Installation
1. Install sender unit, secure to bracket and connect
multiplug .
2. Install nuts (x7) securing plate clamp and fuel tank
service cover.
3. Install fuel tank cover with new seal.
4. Install luggage compartment front floor carpet and retainers (x6).
5. Install luggage compartment rear floor carpet
.
6. Connect battery earth lead.
Fuel Vapour Pipe Assembly-Renew
Removal
1. Battery isolation switch off.
Fig. 1
Fig. 2
$
$
Fig. 3
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilat e vehicle and work area to
remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
ItemCode
Fuel Vapour Pipe Assembly-Renew 10.01.KA
Warning
Read and follow all fuel handling instructions (at the beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and disp ose of fuel contaminated
materials safely.
$

Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-17
2. Remove RH front wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
3. Disconnect quick fit connector fuel vapour pipe to tank.
4. Release fuel vapour pipe from fuel line clips (x4).
5. Disconnect quick fit conne ctor fuel vapour pipe
assembly to purge valve T-piece.
6. Remove fuel vapour pipe.
Installation
1. Install fuel vapour pipe and connect to purge valve 'T' piece.
2. Position fuel vapour pi pe in vapour line clips.
3. Connect fuel vapour pipe to fuel tank.
4. Install RH front wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
5. Battery isolation switch on.
Fuel Supply and Vapour Pipe Assembly-
Renew
Removal
1. Depressurise fuel system (see Workshop Manual procedure 10.01.EK Fuel System - Depressurise).
2. Disconnect vehicle battery. 3. Remove RH front wheel arch liner (see Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
4. Position container to collect spillage from fuel supply pipe.
5. Disconnect quick fit connect or fuel supply pipe to tank
6. Release pipe assembly fr om fuel line clips (x3).
7. Disconnect quick fit connect or fuel supply to manifold
supply (fuel rail) and re move pipe assembly.
Installation
1. Connect fuel supply pipe to manifold supply pipe.
2. Position fuel line in fuel line clips (x3).
3. Connect fuel supply pipe to tank.
4. Install RH front wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
5. Connect vehicle battery.
Manifold Supply Fuel Pipe Assembly-
Renew
Removal
1. Depressurise fuel system (see Workshop Manual procedure 10.01.EK Fuel System - Depressurise).
Warning
Fuel vapour is explosive. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to
eliminate fire risk.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediatel y and dispose of fuel contaminated
materials safely.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the vehicle battery.
Warning
Fuel vapour is explosiv e. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to
eliminate fire risk.
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilate vehicle and work area to remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and dispose of fuel contaminated materials safely.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the vehicle battery.

Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-18 Workshop Manual May 2007
2. Disconnect vehicle battery
3. Remove RH wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
4. Position container to collect fuel spillage.
5. Release fuel supply and vapour pipe from pipe clips (3).
6. Disconnect quick fit connector manifold supply pipe to fuel supply and vapour pipe.
7. Disconnect manifold supp ly pipe from fuel rail.
8. Release manifold supply pipe from pipe clips (x3) and
remove pipe.
Installation
1. Position manifold supply pipe and secure in clips (x3).
2. Connect manifold supply pipe to fuel rail.
3. Connect manifold supply pipe to fuel supply and vapour
pipe.
4. Secure fuel supply and vapour pipe in clips (x3).
5. Install wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
6. Connect vehicle battery.
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilat e vehicle and work area to
remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.

Power Steering (11.02)
Steering (11.00)11-2-2 Workshop Manual Issue 5, January 2010
Maintenance
Power Steering System - Bleed
Procedure
1. Do a check of the fluid level in the PAS fluid reservoir. Add fluid if necessary.
2. Start the engine and let it idle for 20 seconds.
3. Operate the steering fully to the left and then the right through three cycles.
4. Stop the engine.
5. Wait for five minutes then do a check of the fluid level in the PAS fluid reservoir again.
6. Add fluid if necessary.
7. Install the PAS fluid reservoir cap.
Power Steering Pump-Renew
Removal
1. Remove A/C compressor (see Workshop Manual procedure 03.05.BE Compre ssor - Air Conditioning -
Renew).
2. Coolant drain (see Workshop Manual procedure 03.03.AD Coolant - Drain & Refill).
3. Remove PAS fluid from reservoir.
4. Disconnect HP union from PAS pump pipe.
5. Remove bolt P-clip suction hose to body.
6. Remove bolt (x1) HP pump pipe to engine.
7. Remove bolts (x3) PAS pump to engine.
8. Disconnect bottom hose and move aside.
9. Unclip (x1) harness from cylinder head for access.
10. Manouvre pump forward and up.
11. Disconnect suction hose (cut off clip) and remove pump.
12. Remove HP union pipe from pump (mark position on
pump).
Installation
1. Install HP union pipe to pump (align correctly), fit new O-ring.
2. Install pump to vehicle connect suction pipe to PAS pump, align timing marks and fit new clip.
3. Manouvre pump into position.
4. Install bolts (x3) PAS pump to engine (torque).
5. Install bolt (x1) HP pump pipe to engine (torque).
6. Connect bottom hose.
7. Clip (x1) harness from cylinder head for access. 8. Install bolt P-clip suction hose to body (torque).
9. Connect HP union to PAS pump pipe, replace O-ring
(torque).
10. Coolant refill (see Workshop Manual procedure 03.03.AD Coolant - Drain & Refill).
11. Install A/C compressor (see Workshop Manual procedure 03.05.BE Compre ssor - Air Conditioning -
Renew).
12. Top-up PAS fluid.
13. Start and run engine, operate steering lock to lock x2.
14. Top-up PAS fluid.
Power Assisted Steering (PAS) Rack -
Remove and Install
Removal
1. Disconnect the battery ground cable.
2. Remove the front undertray (refer to Workshop Manual Procedure 01.02.NB - Front Undertray).
3. Remove the front wheels and tyres (refer to Workshop Manual Procedure 04.04.ED - Wheel and Tyre - Pair).
4. Remove the front right side wheel-arch liner (refer to Workshop Manual Procedure 01.02.GB - Front Right
Side Wheel-Arch Liner).
5. Put a container in position under the oil tank to collect oil.
6. Remove the drain plug from the oil tank.
Figure 1
7. Let the oil drain into the container.
8. Install and tighten the drain plug into the oil tank (refer to Figure 1).
9. Remove the container.
10. Lower the vehicle.
11. Remove the radiator closing panel (refer to Workshop Manual Procedure 01.02.AA - Radiator Closing Panel).
Repair Operation Time (ROT)
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Power Assisted Steering (PAS) Rack -
Remove and Install 11.02.AA

Power Steering (11.02)
Steering (11.00)
Issue 5, January 2010 Workshop Manual 11-2-11
41. Install the clip that attaches the air intake pipe to the throttle body.
Figure 49
42. Remove and discard the sealing plugs from the two breather pipes and the air intake pipe.
43. Connect the two breather pipes to the air intake pipe.
Figure 50
44. Install the radiator closing panel (refer to Workshop Manual procedure 01.02.AA - Radiator Closing Panel).
45. Fill the oil tank with the correct quantity of oil.
46. Fill the PAS fluid reservoir with the correct quantity of
PAS fluid.
47. Connect the battery ground cable.
48. Bleed the PAS system.
49. Do a check of the engine oi l level. Add oil if necessary.
50. Lift the vehicle.
51. Install the front right side wheel-arch liner (refer to Workshop Manual procedure 01.02.GB - Front Right
Side Wheel-Arch Liner).
52. Install the front wheels and tyres (refer to Workshop Manual procedure 04.04.ED - Wheel and Tyre - Pair)
53. Do a check of the four-wheel alignment.
54. Use the applicable equipment to lift the vehicle and make it safe.
55. Install the front undertray (refer to Workshop Manual procedure 01.02.NB - Front Undertray).
RH/LH Track Rod End-Renew
Removal
1. Raise vehicle on ramp.
2. Remove road wheel(s).
3. Loosen tie rod locknut.
4. Install tool (204 - 524) on front hub, install and tighten
wheel nuts.
5. Lower vehicle to raise suspension sufficient to install ball joint removing tool (204 - 523).
6. Remove nut, track rod end to vertical link.
7. Using (204-523 Ball Joint Sp litter), release track rod end
from vertical link.
8. Remove tool (204 - 524) from front hub.
9. Count number of turns and remove track rod end from tie rod.
Installation
1. Clean track rod end taper and mating face on vertical link.
2. Install track rod end on tie rod the same amount of turns.
3. Install track rod end in vertical link.
4. Install road wheel(s).
5. Lower vehicle on ramp.
6. Carry out full vehicle geometry check/adjust.
7. Torque tie rod ball joint locknut(s).
Power Steering Pump to Rack Hose
Assembly-Renew
Repair Operation Time (ROT)
Repair Operation Time (ROT)

Steering Column (11.04)
Steering (11.00)11-4-2 Workshop Manual Issue 4, November 2008
5. Remove the two screws at the left side of the front face of the column shrouds.
6. Turn the steering wheel to get access to the two screws in the front face of the shrouds at the right side.
7. Remove the two screws at the right side of the front face of the column shrouds.
8. Remove the three screws that attach the bottom shroud to the steering column.
9. On pre-08MY vehicles remove the ignition key from the igniiton switch.
10. Remove the bottom shroud.
11. If a new shroud is to be installed on pre-08MY vehicles, remove the ignition switch grommet.
Install
1. If necessary, install the ignition switch grommet on the bottom column shroud (shroud).
2. Put the shroud in position on the steering column.
3. Install the three screws that attach the shroud to the steering column.
For Pre-08MY vehicles:
4. Put the key in the ignition switch and turn it to position 1 to release the ESCL.
For 08MY vehicles or newer:
5. Put the Emotion Control Unit (ECU) into the docking station at position 2 to release the ESCL.
6. Turn the steering wheel to get access to the two screws in the front face of the shrouds at the left side.
7. Install the two screws at the left side of the front face of the column shrouds. 8. Turn the steering wheel to get access to the two screws
in the front face of the shrouds at the right side.
9. Install the two screws at the right side of the front face of the column shrouds.
10. Put the lower panel on the driver’s side of the instrument panel and engage the seven clips.
Steering Column Gaiter-Renew
Remove
1. Power driver's seat to its lowest and most rearward position.
2. Remove the top and bottom shrouds from the steering column (Refer to ’Top and Bottom Shrouds for the
Steering Column - Remove and Install’, page 11-4-4).
3. Centralise the steering whee l until the steering lock
engages.
4. Remove the ignition key.
5. Disconnect the vehicle battery.
6. Remove the steering wheel (see Workshop Manual procedure 11.06.AB Steering Wheel - Renew).
7. Attach the rotary coupling in position with masking tape.
8. Release the two clips that attach the column switch harness to the load-spread plate.
9. Pull back steering column bulkhead gaiter.
10. Remove and discard pinch bolt, upper column to intermediate shaft.
11. Remove the four Torx bolts that attach the upper column mounting.
12. Release upper column from intermediate shaft.
13. Support steering column assembly.
14. Remove gaiter from steering column.
Install
1. Install the gaiter on the steering column.
2. Put the upper steering column assembly in position and connect it to the intermediate shaft.
3. Position the upper column to the mounting, install and torque the four Torx bolts.
4. Install and torque the column pinch bolt.
5. Put the steering column gaiter in position.
6. Remove masking tape from the rotary coupler.
7. Install steering wheel (see Workshop Manual procedure 11.06.AB Steering Wheel - Renew).
Figure 1
Note: The top screw goes thro ugh the top shroud and a tab
on the bottom shroud to attach it.
Note: The top screw goes thro ugh the top shroud and a tab
on the bottom shroud to attach it.
Note: The top screw goes thro ugh the top shroud and a tab
on the bottom shroud to attach it.
Repair Operation Time (ROT)
ItemCode
Steering Column Gaiter-Renew 11.04.BB
WAR NI NG
LEAVE THE VEHICLE FOR TWO MINUTES AFTER YOU
DISCONNECT THE BATTERY ,BEFORE YOU DO WORK ON THE AIRBAG SYSTEM. IF YOU DO NOT, THE
AIRBAG SYSTEM CAN OPERATE AND CAUSE INJURY.

Steering Column (11.04)
Steering (11.00)
Issue 4, November 2008 Workshop Manual 11-4-3
8. Connect vehicle battery.
9. Install the steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering Column - Remove and
Install’, page 11-4-4).
10. Put the driver’s seat and the steering column in their initial positions.
Upper Steering Column Assembly-
Renew
Remove
1. Power driver's seat to it s lowest and most rearward
position.
2. Remove the top and bottom shrouds from the steering column (Refer to ’Top and Bottom Shrouds for the
Steering Column - Remove and Install’, page 11-4-4).
3. Disconnect vehicle battery.
4. Centralise the steering whee l until the steering lock
engages.
5. Remove the ignition key.
6. Disconnect the battery.
7. Remove the steering wheel (Refer to ’Steering Wheel- Renew’, page 11-6-1).
8. Attach the rotary coupling in position with masking tape.
9. Disconnect steering column switch multiplugs (x5).
10. Remove screw securing load-spread plate to column and collect column shrouds mounting bracket.
11. Release clips (x2) from column switch harness to load- spread plate.
12. Pull back steering co lumn bulkhead gaiter. 13. Remove and discard pinch bolt from upper column to
intermediate shaft.Figure 1
14. Remove the four Torx screws from the upper column mounting.
15. Release upper column from intermediate shaft.
16. Disconnect multiplug from steering sensor and remove
steering column assembly.
17. Unclip steering column sw itches from column and
remove switch gear.
18. Mark fitted position of rotary coupler and remove rotary coupler.
19. Remove gaiter from steering column.
20. Remove Torx screws (x3) from securing steering sensor to mounting bracket.
21. Remove sensor.
22. Remove Torx screws (x3) that secure steering sensor mounting bracket to column and remove bracket.
Install
1. Position steering sensor mounting bracket, install and tighten Torx screws (x3).
2. Install the steering sensor, install and tighten Torx screws (x3).
3. Install gaiter on steering column.
4. Install steering column switch gear and secure clips.
5. Install the rotary coupler to marked position and secure
with masking tape.
6. Position upper steering column assembly and connect to intermediate shaft.
7. Connect multiplug to steering sensor.
8. Position upper column to mounting bracket, install and torque tighten Torx bolts (x4).
9. Install and torque tighten column pinch bolt.
10. Connect multiplugs (x5).
11. Position load-spread plate and secure harness clips (x2).
12. Install load-spread plate and secure with screw.
Repair Operation Time (ROT)

Steering Column (11.04)
Steering (11.00)11-4-4 Workshop Manual Issue 4, November 2008
13. Remove masking tape from rotary coupler.
14. Install the steering wheel (Refer to ’Steering Wheel- Renew’, page 11-6-1).
15. Install air temperature pipe to lower instrument panel
and install panel.
16. Connect the vehicle battery.
17. Install the steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering Column - Remove and
Install’, page 11-4-4).
18. Put the driver’s seat and the steering column in their initial positions.
Top and Bottom Shrouds for the Steering
Column - Remove and Install
Remove the Bottom Shroud
1. Release the seven clips and remove the lower panel from the driver’s side of the instrument panel.
For Pre-08MY vehicles:
2. Put the key in the ignition switch and turn it to position 1 to release the Electronic Steering Column Lock
(ESCL).
For 08MY vehicles or newer:
3. Put the Emotion Control Unit (ECU) into the docking station at position 2 to release the ESCL.
4. Turn the steering wheel to get access to the one or two screws in the front face of the shrouds at the left side. 5. Remove the one or two screws at the left side of the
front face of the column shrouds.
6. Turn the steering wheel to get access to the one or two screws in the front face of the shrouds at the right side.
7. Remove the one or two screws at the right side of the front face of the column shrouds.
8. Remove the three screws that attach the bottom shroud to the steering column.
9. On pre-08MY vehicles remove the ignition key from the ignition switch.
10. Remove the bottom shroud.
11. If a new shroud is to be installed on pre-08MY vehicles, remove the ignition switch grommet.
Remove the Top Shroud
1. Release the steering column adjustment lever.
2. Move the steering wheel to the longest column position.
3. Push the adjustment lever back to lock the steering wheel.
4. Remove the top shroud.
Install the Top Shroud
1. Put the top shroud in position on the steering column.
Install the Bottom Shroud
1. If necessary, install the ignition switch grommet on the bottom column shroud (shroud).
2. Put the shroud in position on the steering column.
3. Install the three screws that attach the shroud to the steering column.
For Pre-08MY vehicles:
4. Put the key in the ignition switch to release the ESCL.
For 08MY vehicles or newer:
5. Put the Emotion Control Unit (ECU) into the docking station at position 2 to release the ESCL.
6. Turn the steering wheel to get access to the one or two screws in the front face of the shrouds at the left side.
7. Install the one or two screws at the left side of the front face of the column shrouds.
8. Turn the steering wheel to get access to the one or two screws in the front face of the shrouds at the right side.
9. Install the one or two screws at the right side of the front
face of the column shrouds.
10. Put the lower panel on the driver’s side of the instrument panel and engage the seven clips.
Caution
Align the steering wheel and the rack to the centre position during assembly. If you do not, the rotary
coupling can be damaged. Al so, it can be difficult to
align the steering wheel in the straight-ahead position.
Repair Operation Time (ROT)
Figure 1
Note: The top screw goes thro ugh the top shroud and a tab
on the bottom shroud to attach it.
Note: The top screw goes thro ugh the top shroud and a tab
on the bottom shroud to attach it.
Note: The top screw goes thro ugh the top shroud and a tab
on the bottom shroud to attach it.

Steering Column (11.04)
Steering (11.00)
Issue 4, November 2008 Workshop Manual 11-4-5
Steering Column Lower Shaft Assembly-
Renew
Remove
1. Operate the driver's seat to its lowest and most rearward position.
2. Raise the vehicle and make it safe.
3. Remove the left side front wheel arch liner (see Workshop Manual procedure 01.02.FB Wheel Arch
Liner - Front - LH - Renew).
4. Remove and discard the link bolt that attaches the lower steering column shaft to the coupling.
5. Release the shaft link for the lower steering column from the coupling.
6. Lower the vehicle.
7. Remove the top and bottom shrouds from the steering column (Refer to ’Top and Bottom Shrouds for the
Steering Column - Remove and Install’, page 11-4-4).
8. Disconnect the vehicle battery.
9. Turn the steering to the centre posiiton to engage the column lock and remove the ignition key.
10. Remove the steering wheel (Refer to ’Steering Wheel-
Renew’, page 11-6-1).
11. Use masking tape to hold the rotary coupling in position.
12. Release the two clips that attach the column switch
harness to the load-spread plate.
13. Pull back the steering column bulkhead gaiter.
14. Remove and discard the pinch bolt that attaches the upper column to the intermediate shaft.
15. Remove the four Torx bolts that attach the upper column mounting.
16. Release the upper column from lower steering column shaft.
17. Use an applicable support to hold the steering column assembly.
18. Remove the lower steering column shaft.
Installation
1. Install the lower steering column shaft.
2. Raise the vehicle and make it safe.
3. Connect the lower steering shaft to the coupling.
4. Install a new bolt but do not torque at this stage.
5. Lower the vehicle.
6. Put the upper steering column assembly in posiiton.
7. Connect it to the intermediate shaft.
8. Put the upper column in position on its mounting.
9. Install and torque the four Torx bolts.
10. Install and torque column pinch bolt. 11. Put the steering column gaiter in position.
12. Remove the masking tape
from the rotary coupler.
13. Install steering wheel (Refer to ’Steering Wheel-Renew’, page 11-6-1).
14. Install the steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering Column - Remove and
Install’, page 11-4-4).
15. Raise the vehicle and make it safe.
16. Torque tighten lower steering column shaft link bolt.
17. Install LH front wheel arch liner (see Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
18. Lower the vehicle.
19. Connect the vehicle battery.
20. Put the driver’s seat and the steering column in their
initial positions.
Repair Operation Time (ROT)
Caution
Align the steering wheel and the rack to the centre position during assembly. If you do not, the rotary
coupling can be damaged. Also, it can be difficult to
align the steering wheel in the straight-ahead position.

Steering Column Switches (11.05)
Steering (11.00)
Issue 4, November 2008 Workshop Manual 11-5-1
Steering (11.00)
Steering Column Switches (11.05)
Maintenance
Ignition Switch-Renew (Pre-08 MY Only)
Remove
1. Operate the driver's seat to its lowest and most rearward position.
2. Remove the steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering Column - Remove and
Install’, page 11-4-4).
3. Disconnect the vehicle battery.
4. Turn the steering wheel to the centre position until the steering lock engages.
5. Remove the screw that attaches the load-spread plate to the column.
6. Remove the mounting bracket for the column shrouds.
7. Release the two clips that attach the column switch harness to the load-spread plate.
8. Release the steering column switch from the column (to give access).
9. Release the ignition switch from the column.
10. Disconnect the electrical connector from the ignition
switch.
Install
1. Connect the electrical connector to the ignition switch.
2. Install the ignition switch onto the column.
3. Install the steering column switch.
4. Put the load-spread plate in position and attach the two harness clips.
5. Install the screw that attaches the load-spread plate.
6. Install the steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering Column - Remove and
Install’, page 11-4-4).
7. Connect the vehicle battery.
8. Operate the driver's seat to its initial position.
Steering Column Stalk Assembly Switch-
Renew (Pre-08 MY Only)
Remove
1. Operate the driver's seat to its lowest and most rearward position.
2. Remove the top and bottom shrouds from the steering column (Refer to ’Top and Bottom Shrouds for the
Steering Column - Remove and Install’, page 11-4-4).
3. Remove the screw that attaches the load-spread plate to the steering column and remove the load-spread plate.
Figure A11-04-1668
4. Collect the mounting bracket for the column shrouds.
5. Release the two clips that attach the column switch harness to the load-spread plate.
6. Disconnect the three electrical connectors from the steering column switches.
7. Release the clips and remove steering column switches from the column.
Install
1. Install the steering column switches and make sure that the clips engage.
2. Connect the three electrical connectors to the column switches.
3. Put the load-spread plate in position and install the two harness clips.
4. Install the screw to attach the load-spread plate.
5. Install the top and bottom steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering
Column - Remove and Install’, page 11-4-4).
6. Connect the vehicle battery.
7. Put the drivers seat and the steering column back to their initial positions.
Repair Operation Time (ROT)Repair Operation Time (ROT)