radio AUDI A5 COUPE 2011 User Guide

Setting power locking
The driver can determine the functions for power locking
in the radio or fv1fv1I*.
In the Central locking menu you can decide which doors
should be unlocked when opening the vehicle.
- Select: [ CAR] function button> Central locking.
For example, if you switch the item Unlocking single door On, the
passenger's door is no longer included in the power locking system,
and will not be unlocked by pressing the unlock button on the master
key remote control.
You can continue to unlock all the doors and the rear lid as before .
Press the opening button on the master key twice .
In addition to this, the
Auto locking can be switched on and off.
When locking the vehicle, all doors and the trunk lid are locked auto ­
matically.
If you switch Trunk lid/tailgate On, then the handle on the rear lid
~ page 51, fig. 42 is locked. In this case the rea r lid can be opened
with the button
cs on the master key~ fig. 35 or with the unlocking
button in the driver's door~
page 51, fig. 41.
When you select
Confirmation tone On, a confirmation tone sounds
when you lock the vehicle .•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Opening and closing
Unlocking and locking the vehicle with the
remote control
Fig. 35 Remote
control: function
buttons
Either the driver's door only or the entire vehicle will unlock
when the unlock button @is pressed once, depending on the
settings in the MMI Central locking menu =>
page 47.
- Press button@(@ ) to unlock the vehicle=> fig. 35 .
- Press button
1'.D (@ ) to lock the vehicle=> & in "General
description" on
page 45.
- Press button C::J (@ ) briefly to unlock the rear lid.
- Press the button
C::J for at least one second to open the
rear lid.
- Push the red !PANIC] button( @) to activate the panic
function. The horn sounds and the turn signals flash. Push
the red [ PANIC] button again to deactivate the panic func­
tion.
If the vehicle is unlocked and no door, the rear lid or the hood is
opened within 60 seconds, the vehicle locks itself again automati­
cally. This feature prevents the vehicle from being accidentally left
unlocked over a long period of time. .,,_
Vehicle care Do-it-yourselt service Technical data

Opening and closing
It depends on the settings in the radio or MMI* whether the entire
vehicle is unlocke d or only cer tain doo rs ~
page 47.
On veh icles w ith a utomat ic transmission*, the selector lever must be
in the
P position, otherwise the vehicle ca nnot be locked .
& WARNING
Read and follow all WARNINGS~ & in "General de scription " on
page
45 .
W Tips
• In order to make sure the locking fu nction is working, you shou ld
always keep your eye on t he vehicle to make sure it is p roperly locked.
• Do not use the remote co ntrol if you are ins ide the car, otherw ise
you may unintentionally lock the vehicle, and then yo u wo uld set off
the ant i-theft alarm when you try to start the engine or open a door.
In case this happens anyhow, push the unlock button
0.
• Use the pa nic function on ly if you are in an emergency situation. •
Applies to veh icles : w ith conven ience key
Unlocking and Locking with convenience
key
The doors and the rear lid can be unlocked and locked
without operat ing the master key.
Unlocking vehicle
Fig . 3 6 Conv enience
key : U nlo cki ng v ehicl e
door
Fig. 37 Conveni en ce
key : Lock ing t he
v ehi cle
- Take hold of the door hand le. The doo r is unlocked auto ­
matical ly.
- Pull t he han dle to open the door.

Locking vehicle
-Move the selector lever to the P position (automatic trans­
mission*), otherwise the vehicle cannot be locked.
- Touch the sensor at the door handle
once ~ page 48,
fig. 37 to lock the vehicle~ & in "General description"
on
page 45 .
The vehicle can be locked and unlocked at any door. It depends on the
settings in the radio or MMI* whether the entire vehicle is unlocked
or one of the doors~
page 47. The master key must be within a
range of about 1.5 m from the appropriate door or the rear lid. It
makes no d ifference whether the master key is in your jacket pocket
or in your brief case.
If you grip the door handle while locking, th is can adversely affect the
locking function.
It is not possible to re-open the door for a brief period directly after
closing it. This allows you to ensure that the doors are properly
locked.
& WARNING
Read and follow all WARNINGS ~ & in "General description" on
page 45.
[ i ] Tips
If your vehicle has been standing for an extended period, please note
the following :
• The proximity sensors are deactivated after a few days to save
powe r. You then have to pull on the door handle once to unlock the
vehicle and a second time to open the vehicle .
• To prevent the battery from being discharged and to preserve your
vehicle's ability to start for as long as possible, the energy manage­
ment system gradually switches off unnecessary convenience func-
Controls and equip ­
ment Safety first
Opening and closing
tions. It is possible that you w
ill not be able to unlock your vehicle
us ing these conven ience f unctions .
• For Declaration of Compliance to United States FCC and Industry
Canada regulations ~
page 343. •
Operating locks with the mechanical key
In the event of a failure of the power locking system, the
driver's door con locked and unlocked with the mechan­
ical key at the lock cylinder.
To unlock the vehicle
Fig. 38 Key turns for
opening and closing
- Insert the mechanical key in to the lock of the driver's
door.
- Turn the mechanical key to position @~ fig . 38.
To lock the vehicle
- Move the selector lever to the P position (automatic trans­
mission*).
- Close all windows and doors properly.
~
Vehicle care Technical data

Clear vision
Adjusting exterior Lighting
The functions are selected in the radio or fvf fvfI *.
- Select : Function button I CAR ]> E xterior lighting .
Coming home*
The coming home function ensures that after
tu rning off the ignition
a nd op enin g th e driv er' s door
the vehi cle periphery is illum inated i n
the dark . In addition, the fron t fog lights, the ta il ligh ts and the
license p late light a re tu rned on . The power-on time can be set for a
period from O (off) to 30 or 60 seconds .
Leaving home *
The leaving home funct ions ensures that
w hen unlocking , the vehicle
periphery is illuminated in t he da rk. In addi tion, the front fog l igh ts,
the tail lights and the license p late light are turned on . This function
can be tu rned on and off.
Auto he adligh ts*
When the light switch is in the AUTO=> page 58 position, the switch­
on point of the l ights can be changed in the automatic driving light
function.
D aytime running lights
T he daytime running lights ca n be tu rn ed on o r off using this func­
tion*. If the function is act ive, the dayt ime runn ing lights are turned
on a utomat ica lly when the ignition is switched on.
[ i ] Tips
T he coming home/ leaving home f unct ion * is avai lab le only wi th the
switch in the AUTO position .•
Daytime running Lights
When you turn on the ignition the daytime running lights
will
come on automatically .
USA models
Th e daytime running lights a re a ct ivated when the lig ht switch
=>
page 58, fig. SO is in the O position or the AUTO position (only in
daylig ht condit ions) . The daytime running lig hts function can be
turned on and off in the radio or MMI* menu
E xterior lighting
=> page 60.
Canada models
Th e dayt ime running lights are act ivated when the lig ht switch
=>
page 58, fig. SO is in the O position, oo oc position or the AUT O posi­
tion (only in day light conditions) . The daytime r unning lights funct ion
cannot be turned off .
& WARNING
Never use daytime runn ing lights to see whe re you a re going . They
are not bright enough and will not l et you see far enough ahead
fo r safety , espe cially at dusk or when it is dark. Be aware of
changes in out side light condition s when you are driving and
r espond by swi tching on your low beams
io .
0 Note
Alw ay s be aware of change s in out side light conditions whil e you
are d riving. Re spond in time to fading d aylight by turning the light
s witch to position
io (or "AUTO ") to turn on you r head lights. •

Clear vision
©·Single wipe
© -Clean the windshield. To eliminate water droplets, the wind­
shield wiper performs one afterwipe operation after several seconds
while driving. You can switch this function off by moving the lever to
posit ion© within 10 seconds of the afterwipe operation. The after­
wipe function is reactivated the next time the ignition is switched on.
Cleaning the headlights*. The headlight washer system* only func­
tions when the light is switched on. The headlights are automat ically
cleaned the first time and every fifth time the lever is moved to posi­
tion ®· They are also cleaned every time you hold the lever in pos it ion
© for longer than 2 seconds.
& WARNING
• The rain sensor is only intended to assist the driver . The driver
is still responsible for manually switching the wipers on according
to the visibility conditions.
• The windshield may not be treated with water-repelling wind­
shield coating agent s. Unfavorable conditions, such as wetness,
darkness, low sun, can result in increased glare. Wiper blade
chatter is also possible.
• Properly functioning windshield wiper blades are required for
a clear view and safe driving=>
page 67, "Replacing windshield
wiper blades" .
0 Note
• In the case of frost, check whether the windshield wiper blades are
frozen to the windshie ld . Switching on the windshield wipers can
damage the wiper blades!
• Prior to using a car wash, the windshield wiper system must be
switched off (lever in position 0). This helps to prevent unintentional
switching on and damage to the windshield wiper system .
[I] Tips
• The w indshield wipe rs are switched off when the ignition is turned
off . Activate the windshield wipers after the ignition is switched back
on by mov ing the windshield w iper lever to any position.
• Worn or dirty windshield wiper blades result in streaking. This can
affect the rain sensor* function. Check your windshie ld wiper blades
regularly.
• The rain sensor* is part of the interval wiping system . Turning off
the ignition will a lso deactivate the rain sensor*. To reactivate the
sensor, switch off the interval wiping function, then switch it back on
again .
• The washer fluid nozzles of the w indshield washer system are
heated at low temperatures when the ignition is on .
• When stopping temporarily, e.g. at a traffic light, the set speed of
the windshield wipers is automatically reduced by one speed .•
Service position
The windshield wiper blades are replaced in the service
position.
Fig . 62 Service posi­
tion
The service position is set in the radio or MMI*.

Seats and storage
Applie s to veh icl es : w ith seat m emo ry
Activating remote control key memory
To be able to recall the stored settings with the remote
control key, the function has to be activated in the radio
orMMI*.
- Select: Function button I CAR]> Seat adjustment>
Driver's seat> Key mem. profile > On.
[ i ] Tips
If you do not want another driver to store their settings on the
remote key, switch off the M emory function using the radio or MMI*
or the !OFF] button ~
page 78. •
A ppli es to veh icles : with seat m em ory a nd MM I
Seat adjustments in MMI
The passenger's seat can be adjusted to various positions
by the driver.
Convenience side view
- Select: Function button I CAR]> Seat adjustment >
Passenger's seat
> Convenience side view.
- Continue to press the control knob until the adjustment
process is complete.
Seat symmetry
Select: Function button I CAR]> Seat adjustment>
Passenger's seat
> Seat symmetry.
- Continue to press the control knob until the adjustment
p rocess is complete.
Using the Convenience side view function, the passenger's seat is
adjusted so that the driver has the best possible view to the right .
When the Convenience side view is set, the specific position of the
driver's seat is taken into consideration.
Using the Seat symmetry function, the passeng er's seat can be
moved to the same position as the driver's seat . The settings for the
driver's seat are import ed and set automat ically.•
Head restraints
Front head restraints
Head restraints that are adjusted according to body size,
along with the seat bealt, offer effective protection.
I
M
-
~ CX) ID
Fig. 73 Front seat:
Adjusting the head
restra int
Fig. 74 Front seat:
Adjusting head
restraint electrically* ..

Warm and cold
Applie s to vehicles : wi th del uxe automatic climate contro l
Setting the temperature
Fig. 97 Temperature
setting regulator
- Rotate the regulator to the left to reduce the tempera-
ture, orto the right to increase the temperature~ fig. 97.
The selected temperature appears on the climate contro l display. The
temperature setting will also appear for a few seconds in the radio or
MMI* display. •
Applie s to vehicles : wit h del uxe automatic cl imate contro l
FanOO
The outomo6colly preset fan speed con be reduced or
increased .
-Press the IS!?] button .
Fig. 98 Fan button
and regulator
- Rotate the regulator to set the desired fan speed (air
volume).
We recommend always running the fan at a low speed when driving
slowly.
To prevent polluted outside air (smell) from entering the interior of
t he vehicle, switch to
recirculation mode by pressing the button 1¢e:>J.
When the radio or MMI* is turned on, the fan speed setting appears
for a few seconds on the screen.
[1] Tips
• It is possible that the fan speed may change automatically. This
occurs to ensure that the desired temperature setting is reached as
quickly as possible .
• The fan speed cannot be regulated separately for the driver and
front passenger. •

Appli es to veh icles: wi th del uxe auto matic c limate contro l
Recirculation mode (~I
The recirculation mode prevents polluted outside air
from entering the vehicle interior.
A ctiva ting
- Press the button [cD] => &.
De activating
- Press the button [cD] again, or
- press the
[AUTO] button.
In recirculation mode, air is drawn from the vehicle interior, filtered
and recirculated . We recommend selecting recirculation mode under
the following conditions:
When driving through a tunnel or in a traffic jam so that exhaust
fumes and odors cannot enter the vehicle interior.
& WARNING
Y ou sh ould not u se the recirc ulati on m ode f or a n exte nded p erio d
si nce no fre sh air is draw n in . With t he air-condi tioning swit ched
o ff, the windows ca n fo g up, whi ch in creases the risk of an
ac cident !•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Warm and cold
App lies to veh icl es: wit h delux e a utoma tic clim ate cont rol
Air distribution [in]
The automatically preset air distribution can be changed.
- Press the [ ·ial button.
Fig. 99 Air distribu­
tion button a nd reg u­
lator
- Rotate the regulator to the desired setting .
You can adjust the air distr ibut ion so that air flows from specific
vents. In position
;J air flows only to the windows, in position :,0, it
flows to the drive r or passenger, and in position
!,J it f lows to the
footwell. There are additional combinations available to adjust air
distribution as needed .
To regulate air distribution automatically, switch to
! AU TO].
When the radio or MMI" is turned on, the air distribution setting
appea rs for a few seconds on the screen. •
Ap plies to v eh icles: with de luxe automat ic cli mate control
Defrost [@]
The windshield and side windows are defrosted or cleared
of condensation as quickly as possible .
-Press the button [@)to turn on the defroster .
Vehicle care Do-it-yourselt service Technical data

1111....__w __ a _r_ m __ a_n_ d_ c_ o _ l_d _______________________________________________ _
(I] Tips
If the climate control is running in cooling mode, air flows mainly
from vents @ and @. To achieve adequate cooling, you should never
close these vents completely. •
Applies to vehicles: with Deluxe automatic cl imate control plus
Rear air vents
The rear air vents are located in the center console.
- Rotate the thumbwheel to open and close the vents .
- To adjust the direction of the airflow from the outlet,
move the tab in the center of the outlet in the desired
direction . The direction of the air delivered from the vents
can be adjusted horizontally and vertically.
The air vents are actuated either automatically or manually
depending on the operating mode selected. Heated or unheated
fresh air, or cooled air flows from the vents .
The air vents to heat the rear footwell are located under the front
seats.
(I] Tips
If the climate control is operating in cooling mode, air flows primarily
from the vents in the center console. To achieve adequate cooling,
you should never close these vents completely. •
Applies to vehicles: with De luxe automatic climate contro l p lus
Economical use of the climate control
system
Economical use of the climate control system helps save
fuel.
When the climate control system is working in cooling mode,
engine performance is reduced and fuel consumption is
affected. To keep the time the climate control system is on as
short as possible, you should do the following:
- To save fuel, turn off cooling mode by pressing the AC
button (indicator light goes out).
- In addition, if you open the window or the panoramic
sliding/tilting sunroof* while driving, turn off cooling
mode by pressing the AC button (indicator light goes out).
- If the vehicle is extremely hot due to the heat of the sun,
briefly open doors and windows.
~ For the sake of the environment
When you save fuel, you reduce emissions from the vehicle. •
Deluxe automatic climate control
plus - basic settings
Applies to veh icles: with De luxe automatic climate control plus
General information
The basic climate control settings can be adjusted in the
radio or f\1/\11*.
-Select: Function button I CAR] > Control button AC. ~

llffl..__O_ n_ t_h _e_ r_o _ a_ d _________________________________________________ _
Starting and stopping the engine
with convenience key
A pplies to veh ic le s: with conven ience ke y
Starting the engine with the
[START ENGINE S TOP] button
This button switches on the ignition and starts the
engine.
Fig. 108 Convenience
key: START ENGINE
STOP button
-Manual transmission: Fully depress the clutch pedal and
move the shift lever to the neutral position.
- Automatic transmission*: Step on the brake pedal and
move the selector lever to
P or N ==> & .
- Press on the [START ENGINE STOP) button==> fig. 108 -
the engine will start.
By pressing the [START ENGINE STOP I button without depressing
the clutch or the brake peal, the ignition is switched on and switched off by pressing it again.
If the engine does not start immediately, stop trying after 10 seconds
and then try to restart the engine about 30 seconds later. After a cold engine is started, there may be a brief period of
increased
noise because oil pressure must first build up in the hydraulic valve
adjusters. This is normal and not a cause for concern.
Driver message in the instrument cluster display
No key identified
This message appears when the !START ENGINE STOP! button is
pressed if there is no master key inside the vehicle or if the system
does not recognize it. For example, the master key cannot be recog­
nized if it is covered by an object (e .g. aluminum brief case) which
screens the radio signal. Electronic devices such as cell phones can
also interfere with the radio signal.
Press brake pedal to start engine
This message appears ifyou pressthe!START ENGINE STOP!
button to start the engine and do not depress the brake pedal. The
engine can only be started if the brake pedal is depressed.
Press clutch pedal to start engine
Th is message appears with a manual transmission when you press
the [START
ENGINE STOP ! button to start the engine and do not
depress the clutch pedal. The engine can only be started when the
clutch pedal is depressed.
Engage N or P to start engine
This message appears when attempting to start the engine if the
selector lever for the autom atic transmission is not in the
P or N posi­
tion. The engine can only be started with the selector in these posi­
tions.
Key not in vehicle
This message appears along with the symbol if the master key is
removed from the vehicle with the engine running. It is intended to
remind you (e.g. when changing drivers) not to continue the journey
without the master key.
If the master key is no longer in the vehicle, you cannot switch on the
ig nition after stopping the engine and you also cannot start the .,_