belt AUDI A5 COUPE 2011 Repair Manual

Child Safety --------------------"'----
& WARNING (continued)
• Always move the passenger seat into its rearmost position in
the seat's fore and aft adjustment range, as far away from the airbag as possible before installing the forward-facing child
restraint. The backrest must be adjusted to an upright position.
• Make sure that the PASSENGER AIR BAG OFF light comes on
and stays on all the time whenever the ignition is switched on.
& WARNING
Rearward-facing child restraints:
• A child in a rearward-facing child safety seat installed on the
front passenger seat will be seriously injured and can be killed if
the front airbag inflates -even with an Advanced Airbag System.
• The inflating airbag will hit the child safety seat or infant
carrier with great force and will smash the child safety seat and
child against the backrest, center armrest, door or roof.
• Always be especially careful if you must install a rearward
facing child safety seat on the front passenger seat in exceptional
circumstances.
• A tight tether strap on a rearward-facing child restraint
attached to the front passenger seat can put too much pressure on
the weight-mat in the seat and register a heavier weight in the
Advanced Airbag System. The heavier weight registered can make
the system work as though an adult were on the seat and deploy the Advanced Airbag when it must be suppressed causing serious
or even fatal injury to the child.
• Make sure that the PASSENGER AIR BAG OFF light comes on
and stays on all the time whenever the ignition is switched on.
• If the PASSENGER AIR BAG OFF light does not come on and
stay on, immediately install the rearward-facing child safety seat
in a rear seating position and have the airbag system inspected by
your authorized Audi dealer. •
Controls and equip­ ment Safety first Vehicle operation
Activating the convertible Locking retractor
Use the convertible locking retractor to secure
a child
restraint.
Always heed the child safety seat manufacturer's instruc­
tions when installing a child restraint in your vehicle. To acti­
vate the convertible locking retractor:
- Place the child restraint on a seat, preferably on the rear
seat .
- Slowly pull the belt
all the way out.
- Route it around or through the child restraint belt path
::::>& .
- Push the child safety seat down with your full weight to
get the safety belt really tight.
- Insert the belt tongue into the buckle for that seating
position.
- Guide the safety belt back into the retractor until the belt
lies flat and snug on the child safety seat .
- You should hear a "clicking" noise as the belt winds back
into the inertia reel. Test the convertible locking retractor
by pulling on the belt. You should no longer be able to pull
the belt out of the retractor. The convertible locking
retractor is now activated.
- Make sure that the red release button is facing away from
the child restraint so that it can be unbuckled quickly.
- Pull on the belt to make sure the safety belt is properly
tight and fastened so that the seat cannot move forward
or sideways more than one inch (2.5 cm) . .,
Vehicle care Do-it-yourself service Technical data

-Child Safety ---------' ~-------------------------------------
in. WARNING
Us ing the wrong child restraint or an improperly in stalled child
re straint can cause seri ou s personal injury or death in a cra sh.
• Always make su re that the safety belt ret racto r is locked when
installing a child safety sea t. An unlock ed safety belt retractor
cannot hold the child saf ety seat in place during normal driving or
in a cra sh .
• Always bu ckle the ch ild safety seat firmly in place even if a
c hild i s not sitting in it . A loose child safety se at can fly around
during a sudden stop or in a crash.
• Alway s make sure the seat backre st to whi ch the child re straint
is installed is in an upright posit ion and securely latched into place
and cannot fold forward. Otherwise , the seatba ck with the child
safety seat atta ched to it could fly forward in the event of an acci­
dent or other emergen cy situation.
• Always read and heed all WARNINGS wheneve r us ing a child
re strained in a vehicle is being used=>
page 215. Special precau­
tions apply when installing a chi ld safety seat on the front
pa ssenger seat=>
page 192, "Child restraints on the front seat -
some important things to know ".•
Deactivating the convertible Locking
retractor
The c onver tible l ockin g retract or fo r child res traints will
b e deacti vated a uto matically when the belt is wound all
t h e way back into the retractor .
-Press the red butto n on the safety belt buckle. T he belt
to ng ue will pop out o f the buckle.
- Guide the safety belt alt the way back into its stowed posi­
t ion.
Always let the safety belt retract completely into its stowed position .
Th e sa fety bel t can now be used as an ordinary sa fety belt withou t the
convertib le locking retractor for ch ild restraints.
If the convertib le locking retractor should be activated inadvertently,
th e safe ty be lt must be unfas tene d and guided comple tely ba ck in to
its stowed position to deactivate this feature. I f the convertib le
lo ck in g re tra ctor is not deact ivate d, the safety be lt w ill gr adu ally
become tighter and uncomfortable to wear.
in. WARNING
Improperly installed child safety seats increase the r isk of serious
per sonal injury and death in a collision .
• Never unfasten the safety belt to deactivate the convertible
locking retractor for child restraints while the vehicle is moving .
You would not be restrained and could be seriously injured in an
accident.
• Always read and heed all WARNINGS whenever using a child
restrained in a vehicle is being us ed => page 215. Special precau­
tions apply when installing a child safety seat on the front
pa ssenger seat=>
page 192, "Child re straints on the front seat -
some impo rtant things to know". •

...,. Child Safety P#J'I ____ _,.__ __________________________ _
Location
Fig. 191 Schematic
overview: LATCH
anchorage point loca­
tions
The illustration shows the seating locations in your vehicle which are
equipped with the lower anchorages system. •
Description
The lower anchorage positions are marked for quick
locating.
Fig. 192 Lower
anchorages,covers
marked
Lower anchorages
Fig. 193 Rear seats:
lower anchorage
bracket locations
Th e lower anchorage attachment points are located on the rear end
of the rear seatback.
Remove the covers=> fig. 192 to access the lower anchorage attach­
ment points .
The lower anchorage attachment points are visible=> fig. 193.
Lower anchorages secure the child restraint in the seat without using
the vehicle's safety belts. Anchorages provide a secure and easy-to­
use attachment and minimize the possibility of improper child
restraint installation .
All child restraints manufactured after September 1, 2002, must have lower anchorage attach men ts for the
LATCH system.
Please remember that the lower anchorage points are only intended
for installation and attachment of child restraints specifically certi­
fied for use with
LATCH lower anchorages. Child restraints that are
not equipped with the lower anchorage attachments can still be
installed in compliance with the child restraint manufacturer's
instructions on using vehicle safety belts .
& WARNING
Improper use of LATCH lower anchorages can cause serious
personal injury in an accident.

Child Safety -
-------------------"'---
& WARNING (continued)
• Always carefully follow the child restraints manufacturer's
instructions for proper installation of the child restraint and
proper use of the lower anchorages or safety belts in your vehicle.
• Never secure or attach any luggage or other items to the
LATCH
lower anchorages.
• Always read and heed the important information about child
restraints in this chapter and WARNINGS~ page
215, "Child
Safety ".•
Installing a child restraint with LATCH
Lower anchorages
Whenever you install a child restraint always follow the
child restraint manufacturer's instructions.
Mounting
Fig. 194 Lower
anchorages : proper
mounting
- Make sure the seatback of the rear seat bench is in the
upright position and securely latched in place.
Controls and equip­
ment Safety first Vehicle operation
-
Attach both hook-on connectors with the spring catch
release on the child safety seat onto the LATCH lower
anchorage so that the connectors lock into place
=> fig. 194.
-Pull on the connector attachments to make sure they are
properly attached to the LATCH lower anchorage.
- Pull straps tight following the child restraint manufac­
turer's instructions .
Releasing
-Loosen the tension on the straps following the child
restraint manufacturer's instructions.
- Depress the spring catches to release the anchorage hooks
from the lower anchorages.
Remember: Use tether straps to help keep the child restraint firmly
in place.
& WARNING
Improper use of the LATCH system can increase the risk of serious
personal injury and death in an accident.
• These anchors were developed only for child safety seats using
the "LATCH" system.
• Never attach other child safety seats, belts or other objects to
these anchors.
• Always make sure that you hear a click when latching the seat
in place. If you do not hear a click the seat is not secure and could
fly forward and hit the interior of the vehicle, or be ejected from
the vehicle.
l)l,
Vehicle care Do-it-yourself service Technical data

lffll.,___C_h_ i_ ld _ S_ a_ f_ e_ t...:: y ;....__ _________________________________________ _
in. WARNING
Improper installation of child restraints will increase the r isk of
injury in an accident.
• Always follow the child restraint system manufacture r's
instructions for proper in stallation of the child restraint sy stem
and proper use of tether straps as well as the lower anchorages or
s afety belts in your vehicle .
• Always read and heed the important informat ion and WARN·
INGS about child safety and the installation of child restraint
systems ~
page 215, "Child Safety ".•
Tether anchors and tether straps
Fig . 1 9 5 T ether
a n ch ors : rece ss fl aps
behind th e rear seat ­
bac ks
The tether anchors for the rear seat ing pos itions are located i n
recesses in the rear win dow sh elf ~ fig. 195 .
A tet he r i s a st raight o r V-shaped strap t hat attac hes the top pa rt of
a ch ild restraint to spec ia l anchorage points in the vehicle .
T he p urpo se of the tethe r is to reduce t he f orwar d movemen t of the
child restraint in a crash, in order to help reduce t he risk of head injury
t ha t could be caused by st riking the ve hicle in terior .
Forward fac ing ch ild restraints manufactured after September 1,
1 999, are required by U.S . federa l reg ulations to comply with child head movement performance req
uirements . T hese new performance
re qu iremen ts m ake a tet he r ne cessa ry on most new child sa fe ty
seats.
in. WARNING
Improper installation of child restraints will inc rease the risk of
injury and death in a cra sh .
• Alw ays follow the instructions pro vided by the manuf acturer
of the child restraint you intend to install in your Audi.
• Improper use of child re straint anchors (including tether
anchors) can lead to injury in a collision. The anchor s are designed
to withstand only those loads imposed by co rrectly fitted child
restraint s.
• Never mount two child restraint systems on one LATCH lower
anchor point .
• Never attach two child restraint systems to one tether strap or
tether anchorage.
• Never attach a tether strap to a tie-down hook in the luggage
compartment .
• Never u se child restraint tether anchorage s to secure safety
belts or other kinds of occupant rest raints.
• Never secure or atta ch any luggage or other items to the LATCH
lower anchorages or to the tethe r ancho rs.
• If a tether or other strap is used to attach a child restraint to
the front passenger seat , make sure that it is not so tight , that it
causes the weight -sensing mat to mea sure more weight than is
actually on the seat.
• The heavier weight register ed can make the Advanced Airbag
System work as though an adult were on the seat and deploy the
Advanced Airbag when it must be suppre ssed causing serious or
even fatal injury to the child.
• If you must install a rearward facing child safety seat on the
front passenger seat because of e xcept ional circumstances and
the PASSENGER AIR BAG OFF light does not come on and stay on,
~

ffl.___C_ h_ il_d _ S_a _ f_ e _ t--= y '------------------------------------------------
& WA RNING (conti nued)
• A tight tether or other strap on a rearward-facing child
restraint attached to the front passenger seat can put too much
pressure on the weight -mat in the seat and registe r a hea vier
weight in the Advanced Airbag System . The heavier w eight regis­
tered can make the system work as though an adult were on the
s eat and deploy the Advanced Airbag when it mu st be suppressed
causing se rious or e ven fatal injury to the child.
• If you must install a rearward facing child safety seat on the
front p assenger seat because of e xceptional circumstances and
the PASSENGER AIR BAG OFF light does not come on and stay on,
immed iately install the rearward-facing ch ild safety seat in a rear
s eating position and have the airbag system inspected by your
authorized Audi dealer .•
Additional Information
Sources of information about child
restraints and the ir use
There are a number of sources of additional information abo ut child
restrain t selec tion, insta llation and use:
NHTSA adv ises that the best chi ld safety seat is the o ne that fits you r
child and fits in your vehicle, and that you will use correctly and
c ons iste ntly .
Try before you buy !
U.S National Highway Traffic Safety Administration
T e l. : 1-888-327 -4236 (T TY: 1-800 -424 -9 153)
www.n htsa.gov
National SAFE KIDS Campaign
Tel. : (202) 662-0600
www.safekids .org
Safety BeltSafe U.S.A
T e l. : (8 00) 74 5-SAF E (E ng lish)
Tel.: (800) 747 -SANO (Spa nish)
www.carseat .or g
Transport Canada Information Centre
Te l. : 1 (800) 333-0371 or call 1 (6 13) 998 -8 6 16 if yo u are in t he
Ottawa area
www. tc.gc.ca/roads afety
Audi Customer CARE
T el.: (800) 822-2834 •

Intelligent technology
~----------------------------------------------
Intelligent technology
Notice about data recorded by
vehicle control modu Les
Your vehicle is not equipped with an Event Data Recorder (EDR),
installed by some manufacturers for the express purpose of
capturing data for retrieval after an accident or crash event. EDR's are
sometimes called "crash recorders".
Some state laws restrict the retrieval or downloading of data stored
by ED R's that were installed in a vehicle for the express purpose of
retrieving data after an accident or crash event without the owner's
consent.
Although your vehicle is not equipped with an EDR, it is equipped with
a number of e lectronic control modules for various vehicle systems
such as, for example, eng ine function, emission control, as well as for
the airbags and safety belts.
These electronic control modules also record vehicle-related data
during normal vehicle operation for diagnostic and repair purposes .
The recording capacity of the electronic control modu les is limited to
data (no sound is recorded) and only a sma ll amount of data is actu­
ally recorded over a very limited period of time and stored when a
system fault or other condition is sensed by a control unit. Some of
the data then stored may relate to vehicle speed, direction, braking
as well as restraint system use and performance in the event of a
crash or other condition. Stored data can only be read and down­
loaded with special equipment .•
Electronic stabilization Program
(ESP}
Ce-ieral lnforrrc:t~on
The ESP improves the vehicle stability.
Fig. 197 ;';. OFF
button
Fig. 198 Center
console with;';.
OFF
button
ESP is designed to he lp you maintain vehicle control in situations
where the car approaches the limits of "grip", especially when accel­
erat ing and cornering. ESP reduces the risk of skidding and improves
stability under all road conditions.

____________________________________________ C_l_e _a_ n_ i n--= g,___ a_n_ d----' p,___ r_o _t_ e_ c_ t_ i _o_ n __ _
The intensity of the color determines the visual characteristics and
appea rance. If the s urface of the leather has a typical natu ral look,
then the leather is a nappa leather that has been left in a relatively
natura l condition. This leather offers partic ularly good comfort and
breathes well. Fine veins, closed grains, insect b ites, sk in folds, and
subtle var iations in co lor remain visible. These character istics demon­
st rate that the mater ia l is nat ura l.
Natural nap pa leather is not covered by a color fin ish. It is therefore
mo re sensitive to soiling and we ar, which is some thi ng you need to
consider if children, animals or other factors mig ht prove to be partic­
ularly hard on the leather.
By contrast, leather types that a re cove red by a colo red fi nish layer
are more durab le . This has a positive effect on the leather's resistance
to wear and so ilin g in daily use. On the othe r hand, the typical charac­
teristics of natura l leather are barely or not apparent . However, this
does not mean that the leathe r itse lf is of inferio r quali ty.
Care and handling
Be cause of the exclusive na ture of t he types of leat her t ha t Audi uses
and their unique properties (such as sensitivity to oils, grease, soiling,
e tc. ), yo u will need to be somewhat c arefu l with these leat hers , a nd
a certain type of care is requ ired. For example, dark clothing mate­
r ia ls can dis co lor leather seats (especially if s uch cloth ing is damp and
was not dyed correctly). Dust and dirt particles in pores, folds, and
seams can have an ab rasive effect and can damage the leathe r
surface as well as weaken seams.
T he leather s ho ul d be cleaned regularly as needed . After having been
used for a relatively long time, your leather seats will a cquire a rich
aged f in ish. This is a characterist ic of natura l leather and a s ign of
t rue quality.
In order to maintain the value of this natural product over the life of
yo ur vehicle, you sho uld fo llow the recommendations below :
Safety first
0 Note
• To keep you r leat he r from b leach ing out, do not a llow it to be
exposed to bright s unlight for long periods of time . If yo u have to
leave t he veh icle parked o utside for long pe riods, cover the leather to
protect it from direct exposure to sunlight.
• Sharp objects on clot hing, such as z ippers, rivets or sha rp pieces
on belts can leave permanent scratches or scrape mar ks on the
surfa ce of the leathe r.
(I] Tips
• After ea ch t ime you clean the le athe r and at regular inte rvals, use
a leather preservat ive cream that contains UV-blockers and that
works into the leather . This cream will nourish and moistu rize the
leather, helping it to breathe and stay supp le. It also he lps to build up
a protect ive coa ting on the surface .
• Clean the leather every 2 -3 months, and clean any areas t hat get
so ile d.
• Remove fresh marks made by ballpoint pens, ink, lipstick, shoe
polish, etc. as soon as poss ible.
• Preserve the color of the leather as needed by using a special
c o lored leat he r car e cream to touch up a reas of uneven color. •
Applies to vehicles: w it h na tur al leat her
Cleaning and caring for leather upholstery
and trim
Natural leather requires s pecial care and attention .
Normal cleaning
-Clean soiled areas w it h a slightly moistened cotton or
woolen cloth.
Vehicle care Technical data

____________________________________________ C_l_e _a_ n_ i n--= g=--- a_n_ d----' p,__ r_o _t_ e_ c_ t_ i _o_ n __ lffll
- Once the sta in is no longer v isible, use a soft dry cloth or
tissue to soak up t he mois ture.
Do not use leathe r cle an in g p rodu cts on Alc ant ara® .
You may use a suitable shampoo for removing dust and d irt.
Dust an d grit in the pores and seams can scratch and damage the
surface. If the car is left standing in th e su n fo r long p eriods, th e
Alcantara ® sho uld be protected against direct sun light to prevent it
from fading. S lig ht co lor var iat io ns w ill develop in no rm al use a nd are
not a n ind ication of mater ial deterio ration.
0 Note
• N ever use chem ica l solvents (e .g . lighter fluid, turpentine), waxes,
shoe polish or sim ilar pr od uct s on A lc antar a® su rfa ces .
• To avo id damage, have stubborn sta ins removed by a commerc ia l
cl eaning spe cialis t.
• Do not use brushes, stif f sponges or sim ilar ly abrasive clea ning
aids .•
Safety belts
O nly well -maintained s afety belts work reli ably when
nee ded .
- Keep bel ts clean.
- F or cl ean ing , u se a mild so ap and wa ter so lut io n. Let belts
dr y t ho ro ughly and a way fr om direct s unlig ht .
- Do not a llow in ertia re el safety b elt s to retrac t be fore they
are co mpletely dry.
- Chec k t he co ndition of yo u r safety be lts
regularly .
Heavily soiled safety be lts may not retract properly.
Safety first
& WARNING
Damaged safety belts can break in a crash.
• Anything that might damage your safety belts could mean
that you and your passengers would not be adequately protected
in an accident.
• Safety belt performance depends on correct installation . Never
remove belt s from the vehicle to clean them .
• Do not use chemical cleaning agents , bleach or dyes. They have
corrosive properties which weaken the webbing.
• When cleaning your safety belts , inspect them fo r damage . If
you discover damage, see your authorized Audi dealer.
• Always read and heed all WARNINGS and other information
~page 256. •
Engine compartment
B e especi ally careful when clean ing the engine co m part ­
me nt.
Always switch off the ign ition before cleaning the engine~& .
Plenum panel
Remove leaves from the plenum pane l in front of the win dshi eld
under the eng ine hoo d. Thi s preven ts the water d rain holes fro m
becoming blocked, and it prevents debris from enter ing th e veh icle
in ter ior thro u gh t he heat ing and ven tilat ion ducts.
Corrosion protection
Th e eng ine com partment and transm iss io n have bee n co rros io n­
protected at the facto ry .
G oo d ant i- cor ros io n trea tmen t is very i mport an t, pa rt icu larly in t he
wi nte r. If the ve hicle is freq uently d riven on sa lt treated roads, the
entire engine compartment and plenum pane l sho uld be tho roug hly .,
Vehicle care Technical data

lffll __ C_h_ e_c _k _i_n -=g :a,__ a_n_ d_ f_ i_ l _li _n _,g;._ __________________________________________ _
& WARNING (continued )
-First, fully apply the parking brake , move selector lever of
automatic transmission to "P" (Park); put manual transmi s­
sion in Neutral.
- Alway s use extreme caution to prevent clothing, jewelry , or
long hair from getting caught in the radiator fan , V-belts or
other moving part s, or from contacting hot parts. Tie back hair
before starting , and do not wear clothing that will hang or
droop into the engine .
• Minimize expo sure to em is sion and chemical hazards=>& .
& WARNING
California Proposition 65 Warning:
• Engine exhaust , some of its constituents, and certain vehicle
c omponents contain or emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and reproductive harm. In
addition , certain fluid s contained in vehicle s and certain products
of component wear contain or emit chemicals known to the State
of California to cause cancer and birth defects or other reproduc­
tive harm.
• Battery posts, terminals and related acces sories contain lead
and lead compounds, chemicals known to the State of California
to cause cancer and reproductive harms. Wash hand s after
handling .
0 Note
When adding fluids, a lways make sure that they are poured into the
proper container or filler opening, otherwise serious damage to
veh icle systems w ill occur.
<£' For the sake of the environment
T o de tect leaks in time, inspect the veh icle floo r pa n from u nder neat h
regu larly. If you see spots from oil or other vehicle fluids, have your
vehicle inspe cted by an au thor ized Aud i dea le r.•
Engine compartment
Engine compartment
These are the most important i tems that y ou can chec k.
Fig. 205 Typ ical layout f or contain ers and engine o il filler cap
(D Jump start poi nt( +) unde r a cover . .... ..... .. .... 288, 3 29
@ Brak e fluid reservo ir ( ) . . . . . . . . . . . . . . . . . . . . . . . . 284
® Engine oil fill er cap(~) . . . . . . . . . . . . . . . . . . . . . . . . 279
© Coolant e xpansion tank (- L ) . . . . . . . . . . . . . . . . . . . . . 282
® Jump start point( -) with hex head screw ........... 288,329.,.