SEN AUDI A6 2012 User Guide

-When you leave the vehicle, always take
the ignition key with you. This will pre­
vent passengers (children, for example)
from accidentally being locked in the ve­ hicle should they accidentally press the
power locking switch in the doors .
- Do not leave children inside the vehicle
unsupervised. In an emergency it would
be impossible to open the doors from
the outside without the key.
- Applies to vehicles with power side door
closer*:
- When closing a door, make sure noth­
ing can interfere with the door. This
could cause serious personal injury.
- You can stop the door from closing at
any time by pulling on the inside or
outside door handle .
@ Tips
-In the event of a crash with airbag de­
ployment all locked doors will be auto­
matically unlocked to give access to the
vehicle occupants from the outside.
- If the power locking system should mal­
function, you can lock the driver's door
using the mechanical key¢
page 36 .
-If the power locking system should fail,
you can still open the fuel tank flap in an
emergency ¢
page 218.
-You are well advised not to keep valua ­
bles inside an unattended vehicle, visible
or not . Even a properly locked vehicle
cannot provide the security of a safe .
- If the LED in the upper edge of the driv­
er's door panel comes on for about 30
seconds after the vehicle is locked, there
is a malfunction in the power locking or
the anti-theft warning system. Have the
malfunction corrected by an authorized
Audi dealership or qualified repair facili­
ty.
Opening and closing 33
Setting power locking
T he driver can determine the functions for
power locking in the MMI .
.,. Select: !CAR !function button> Car systems
control bu tton > Vehicle settings > Central
lo cking .
Unlock doors -
You can decide if All doors or
only the
Dri ver should unlock. The rear lid al­
so unlocks when
All is selected . If you select
Driver in a vehicle with a convenience key* ,
only the door whose handle you pull will un­
lock.
If you select
Driver , all the doors and rear lid
will unlock if you press the
ffi button on the re­
mote control master key twice .
Lock exterior trunk handle -If you selec t On,
the rear lid handle is locked . In this case the
rear lid can be opened with the button
a on
the master key or with the
a button in the
driver's door . In vehicles with a convenience
key* , you can still open the rear lid using the
handle if an authorized master key is near the
proximity sensor .
Fold mirrors* -If you select On, the exterior
rearview mirrors fold in automatically when
you press the
(TI button on the remote contro l
master key or touch the sensor* in the handle .
Lock when driving -If you select On, the vehi ­
cle locks automatically when driving. All of
the doors and rear lid lock.
Tone when locking -When you select On, a
confirmation tone sounds when you lock the
vehicle.

34 Openin g and clo sing
locking and unlocking the vehicle with
the remote control
F ig. 19 Remote control: function buttons
N 0
9 (!)
~
Either the driver's door only or the entire veh i­
cle will unlock when the unlock button
III( @)
is pressed once, depend ing on the settings in
the MMI
¢page 33.
.. Press button III( @) to unlock the vehicle
¢fig .19 .
.. Press button fij (@ ) to lock the vehicle¢.&,
in General description on page 32 .
.. Press b utton c:s (@ ) briefly to un lock the
rear lid .
.. Push the red
!PANIC I button( @) to activate
the panic f unction. The horn sounds and the
turn signals flash. Push the red
!PANIC I but­
ton aga in to deact ivate the panic function.
If the vehicle is unlocked and no door, the rear lid or the hood is opened within 60 seconds,
the vehicle locks itself again automatically.
This feature prevents the vehicle from being
accidentally left unlocked over a long period
of time .
It depends on the settings in the MMI wheth­
er the entire vehicle is unlocked or only cer­
tain doors
¢ page 33.
A WARNING
Read and follow a ll WARNINGS c:> .&. in
General description on page 32.
@ Tips
- In order to make sure the locking func­
tion is working, you should always keep
your eye on the vehicle to make sure it is
properly locked. -
Do not use the remote control if you are
inside the car, otherwise you may unin­
tentionally lock the vehicle, and then you
would set off the anti-theft alarm when
you try to start the eng ine or open a
door. In case this happens anyhow, push
the unlock button
III-
- The vehicle can only be locked when the
selector lever is in the
P posit ion.
- Use the panic function only if you are in
an eme rgency s ituation.
locking and unlocking with convenience
key
Applies to vehicles : with convenience key
The doors and the rear lid can be unlocked
and locked without operating the master key .
Fig . 20 Conven ience key: Lock ing the vehicle
Unlocking vehicle
.. Take ho ld of the door handle. The door is
un locked automatically.
.. Pull the handle to open the door.
locking vehicle
.. Select the P selector lever position . Other­
w ise the vehicle cannot be lo cked.
.. To lock the veh icle, close the door and touch
the sensor in the door handle
on ce c:> fig . 20 .
Do not reach inside the door handle.
T he veh icle can be locked and unlocked at any
doo r. T he master key must be within a range
of about 1.5 m from the appropriate door or
the rear lid. It makes no difference whether
the master key is in your jacket pocket or in
your brief case.

It is not possible to re-open the door for a
brief period direct ly after closing it. This al­
low s you to ensure that the doors are properly
l ocked.
It depends on the settings in the MMI wheth ­
er the entire vehicle is unlo cked or one of the
doors
¢page 33.
A WARNING
Read and follow all WARNINGS c> ..&. in
General description on page
32.
@ Tips
-
If your vehicle has been standing for an ex­
tended period, please note the following:
- The proximity sensors are deactivated af-
ter a few days to save power. You then
have to pull on the door handle once to
unlock the veh icle and a second time to
open the veh icle.
- To prevent the battery from being dis­
charged and to preserve your vehicle's
ability to start for as long as possible,
the energy management system gradu­
al ly sw itches off unnecessary conven­
ience functions.
It is possible that you
will not be able to unlock your vehicle us­
ing these convenience functions.
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions~
page 281.
Operating locks with the key
In the event of a failure of the power locking
system, the driver's door can be locked and
unlocked at the lock cylinder.
•
Fig. 21 Key turns for opening and clos ing.
Opening and closing 35
.. Remove the mechanical key Q page 31 .
.. Turn the mechanical key to position @
r::!) fig. 21 to unlock the driver's door .
.. Turn the key to position
@ to lock the d riv­
er's door
q ,&. .
A WARNING
Read and follow all WARNINGS Q ..&. in
General description on page
32.
Locking and unlocking the vehicle from
inside
Fig. 22 Drive r's door: power locking switch
Fig. 23 Rear power locking switch
.. Press t he button [ml to lock the vehicle q ,&. .
.. Press the button Im to unlock the veh icle.
If you lock the vehicle using the power locking
switch, please note the following:
- You cannot open the doors or the rear lid
from the
outside (increased security, for ex­
ample when you are stopped at a red light).
- The diodes in the power locking switches il-
luminate when all the doors are closed and
locked.
- Front doors: you can unlock and open the
doors from the inside by pulling on the door
handle. ..,.

36 Opening and clo sing
- Rear doors : pu ll the door handle once to re­
l ease the lock. Pull the handle
again to open
the door .
- If you have a crash and the airbag is activat­
ed, the doors automatically un lock .
A WARNING
-The power locking switch works with the
ignition off and automatically locks the
entire vehicle whe n it is actuated .
- On a vehicle locked from the outside the
power locking system switch is inopera­
t ive .
- Locking doors from the inside can help
prevent inadvertent door opening during
an acc ident and ca n also prevent unwa nt­
ed entry from the outs id e. Locked doors
can, however, de lay ass istance to ve hicle
o ccupants and hold up res cue efforts
from the o utside in an a ccident or other
emergency.
(D Tips
Your vehicle is locked automatically at a
speed of 9 mph (15 km/h)
Q page 32 . You
can unlo ck the vehicle again us ing the
open ing f unct ion in the power lock ing sys ­
tem switch.
Emergency locking
Each door must be locked separately if the
pow er locking system fails.
Fig . 2 4 Doo r: Em erge ncy loc king
An emergency lock is located on the f ront end
of the passenger's door and the rear doors (on ly visible when door is open) .
.. Remove the mechanical key
Q page 31 .
.. Pull the cover cap out of the opening
~fig . 24 .
.. Insert the key in the ins ide slot and turn it
all the way to the right (right door) or left
(left door) .
Once the door has been closed, it can no lon­
ger be opened from the outside. The doo r can
be opened from the inside by pulling the door
handle. If the child safety lock in a rear door is
activated, you must f irst pu ll the door handle
on the inside . Then you ca n ope n the doo r
from t he outside .
Rear lid
Opening and closing rear lid
Fig. 25 Drive r's doo r: remote rear lid re lea se
Fi g. 2 6 Posit io n of h an dl e in th e r ear l id
Opening the rear lid
.. Press the midd le butto n~ on th e remote
cont ro l maste r key for at least one second,
o r
.. Pull the re lease but to n
l= I in the driver's
door
Q fig. 25, o r
.. Press t he handle on the rear lid
~ fig. 26.

38 Openin g and clo sing
- The power windows in the rear doors,
- The interior l ighting buttons.
In order to activate the child safety lock on
the left and the right side, press the two safe­
ty buttons [!l in succession.
Power windows
Controls
The driver can control all power windows .
Fig. 29 Section of the driver's door: Controls
All power window switches are provided with
a tw o-p osition fun ction :
Opening th e window s
• Press the switch to the
firs t stop and hold it
until the window reaches the desired posi­
tion.
• Press the switch br iefly to the
se cond stop
to automatically open the window .
Cl os in g th e window s
• Pull the switch to the
firs t s top and hold it
until the window reaches the des ired pos i­
tion.
• Pull the switch briefly to the
sec on d sto p to
automatically close the window .
P ow er wi ndow switche s
@ Driver's door
® Passenger's door
© Left rear door
® R ight rear door
A WARNING
- When you leave your veh icle -even if on­
ly briefly -always take the ignition key with you. This applies particularly when
children remain in the vehicle. Otherwise
the children could start the engine or op­
erate electrical equipment (e.g. power
windows). The power windows are func­
tional unt il the driver's door or passeng­
er's door has been opened.
- Be careful when clos ing the windows .
Check to see that no one is in the way, or
serio us inju ry cou ld result!
- When locking the vehicle from outside,
the vehicle must be unoccupied since the windows can no longer be opened in an
emergency.
(0 Tips
Afte r the ignition has been switched off,
the w indows can still be opened o r closed
fo r abo ut 10 minutes. The power windows
are not switched off until the driver's door
or passenger's door has been opened.
What to do after a malfunction
The one-touch open and close function must
be reactivated if the battery has been discon­
nected.
• Pull and ho ld the power window sw itch un­
til the w indow is f ully closed.
• Release the sw itch and then pull it again for
at least one second .
Valet parking
The valet parking feature protects the lug­
gage compartment from unauthorized ac­
cess.
F ig. 30 Luggage compartment: valet park ing button

With "valet parking" activated, the rear lid
cannot be opened.
~ Remove the mechanical key¢ page 31.
~ Open the glove compartment and activa te
¢
fig. 30 the "valet parking" feature by
pressing the
I VALE T I button. The indicator
light in the switch illuminates.
~ Close the glove compartment and lock it
with the mechanical key.
~ L eave the master key with the service per ­
sonnel for parking and keep the mechan ical
key w ith you .
When the "valet parking" feature is activated:
- the un locking button for the rear lid
e::5 in
the dr iver's door is inactive
- the button
C::5 on the master key is inactive
- the opening hand le in the rear lid is inactive.
The vehicle can be driven and locked and un­
locked w ith the master key. Access to the lug ­
gage compartment is blocked.
When the valet parking function is switched on, the message
Valet parking activated ap­
pears in the instrument cluster display when
you switch the ig nition on.
Sliding/tilting sunroof
Operation
Fig . 31 Sect io n of t he he adlin er: S lidin g/tiltin g sunroo f
b u tto n
@ Tilting and sliding
~ To tilt the sunroof completely, press the
switch briefly to the second leve l¢
fig . 31
briefly.
~ To close the sunroof completely, pull the
switch briefly to the second level ¢
.&_.
Opening and closing 39
~ To se lect an intermediate position, press/
pull the switch to the first level until the de­
sired position is reached .
@ Opening and closing
~ To open the sunroof completely , slide the
button back br iefly to the second level.
~ To close the sunroof completely, slide the
button forward briefly to the second level
¢ .&_.
~ To select a partially open position, slide the
button forward/back to the first level until
the roof reaches the desired position .
A wind deflector integrated into the sliding/
tilting sunroof adapts automatically to the
speed and sunroof pos ition . This reduces wind
noise to a minimum in all sunroof positions .
You can still close or open the sunroof for up
to ten minutes after you have switched the ig­ nition off . The switch is deactivated once the
driver's or front passenger's door is opened .
Solar protection
The solar protection opens automat ically
when the sunroof opens.
The sun shade can be opened and closed by
hand when the sunroof is closed.
A WARNING
-Pay careful attention when closing the
sliding/tilting sunroof -otherwise serious
injury could result! Always take the key
with you when leaving the vehicle .
(D Note
-
Always close your sliding/tilting sunroof
when leaving your vehicle. Sudden rain can
cause damage to the interior equipment of
your vehicle, particularly the electronic equipment .

42 Clear vision
visibility conditions. For example, fog cannot be detected by the light sensors.
So always switch on the headlights
io
under these weather conditions and
when driving in the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists . Always turn on
the headlights so that you can see ahead and so that others can see your car from
the back.
(D Note
The rear fog lights should only be turned
on in accordance with traffic regulation, as
the lights are bright for following traffic.
@ Tips
-In the event of a light sensor malfunc­
tion, the driver is notified in the instru­
ment cluster display~
page 22.
- You will hear a warning tone if you open
the driver door when the exterior lights
are switched on.
- Please observe legal regulations when
using the lighting systems described .
Emergency flasher
The emergency flasher makes other motorists
aware that you or your vehicle are in an emer­
gency situation.
Fig. 33 Center console : emerge ncy flasher switch
• Press the switch~~ fig. 33 to turn the
emergency flashers on or off.
When the emergency flasher is on, all four
turn signals blink at the same time. The turn signal
indicato r lights ¢ Q in the instrument
cluster, as well as the light in the emergency
fl asher switch ~ blink likewise. The emergen­
cy flashers also work when the ignition is
turned off.
The emergency flashers will turn on automati­
cally if you are in an accident where the airbag
has deployed .
(D Tips
You should turn on the emergency flashers
when:
- you are the last vehicle standing in a traf­
fic jam so that any other vehicles coming
can see you, or when
- your vehicle has broken down or you are
in an emergency situation, or when
- your vehicle is being towed by a tow
truck or if you are towing another vehicle
behind you.
· Adjusting the exterior lighting
The settings ore adjusted in the MMI.
• Select: I CAR I function button > Car systems
control button > Vehicle settings> Exterior
lighting.
Automatic headlights
You can adjust the following settings in the
Automatic headlights menu :
Headlights activation time -You can adjust if
the headlights switch on
Early , Med. or Late
according to the sensitivity of the light sensor .
Audi adaptive light* -You can switch adaptive
light
On and Off .
Daytime running lights
USA models:
You can switch the daytime run­
ning lights
on and off.
Canada models:
The function cannot be
turned off.
It is activated automatically each
time the ignition is switched on. This menu
item is shown "greyed out".

Vision
Sun visors
( J
Fig. 38 Sun v isor
The sun visors for the driver and passenger
can be released from their brackets and
turned toward the doors
c::> fig. 38 @.
The mirror light switches on when the cover
over the vanity mirror @opens.
Sun shad e
Applies to vehicles: with s un shade
Fig . 39 Sun s hade pulled up on th e rear w indow
Fig. 40 Cockp it: sun shade sw itc h
Rear door sunshade*
.,. Pu ll the sun shade out and attach it to the
hoo ks on the upper doo r frame
c::> fig. 39.
Clear vi sion 45
Rea r window sun shad e*
.,. To extend/retract the sun shade, press the
button~
c::> fig . 40 .
You can adjust the settings for the rea r sun
shade so the shade re tracts automatically
when you select the reverse gea r. Select:
CAR
function button > Car system s control b utton
> V ehicle settings > Automatic re ar blind >
O n. The settings are automatically stored and
ass igned to the remote control key. The sun
shade extends again as soon as the vehicle be­
gins traveling forward at a speed greater than
9 mph (15 km/h), as long as the ig nition has
not been sw itched off in the meantime.
,&. WARNING
When lowering or ra is ing the sunshade,
make sure there is nothing in its way and
that it has a free path to travel. This co uld
cause persona l inj ury .
(j} Tips
- If the sun shade is ope rated repeatedly
w ithin a short t ime, the built- in overlo ad
pro te ct io n circuit may be tripped . If th is
occurs, you will have to wait briefly be­
fore yo u can operate the shade again.
- Because of the decrease in the f lexibility
of the shade materia l at temperatures
below freezing, t he e lectr ica l circuit
w hich operates the shade shuts off when
the temperature in the vehicle falls be­
low
14 °F (-10 °C). The shade cannot be
operated until the passenger compart­
ment warms up above t his temperature .

46 Clear vis ion
Wiper and washer
system
Switching the windshield wipers on
F ig. 4 1 Windsh ie ld wipe r lever
Move the windshield wiper lever to the corre­
spond ing pos ition:
@ -Windshie ld wipers off
(I) -Rain sensor mode . The windshield w ipers
switch on once the vehicle speed exceeds ap­
proximately 2 mph (4 km/h) and it is raining.
The higher the rain sensor sens it ivity is se t
(switch @to the right), the earlier the wind ­
shield wipers react to moisture on the wi nd­
shie ld. You can deact ivate rain sensor mode in
the MMI, which w ill then activate intermi ttent
mode. Selec t:
ICAR I function bu tton > C ar s ys­
t e m s
contro l bu tton > Dri ver a ssis t > Rain
se nsor
> Off . In intermittent mode, you can
adjust the interval time using the switch @.
@-Slow wiping
@-Fast wiping
©-Single wipe. If you hold the lever in this
posi tion longer, the wipers sw itch from slow
wiping to fast wip ing .
® - Clean the windshield . The wipers wipe
one time after several seconds of driv ing to
remove water drop le ts. You can switch this
function off by mov ing the lever to position ®
within 10 seconds after the afterw ipe . The af­
terw ipe fun ct ion is react ivated the next time
you swit ch the ig nitio n on .
Clean ing the headlights . The headlight wash ­
e r system* only functions when the lights are
switched on . The headlights and the night vi- s
ion system camera * are cleaned automatical ­
ly the first time the lever is press in position
® and every 8 times it is pressed after that.
They a re also cleaned every time you ho ld the
lever in posit ion ® for longer than 8 seconds.
A WARNING
--The rain sensor is only designed to assist
and support the dr iver .
It rema ins enti re­
ly the d river's responsibility to monitor
outs ide weather cond itions and to ma n­
u a lly activate the wipe rs as soon as rai n
or drizzle reduces visibility through the
windshie ld .
- The windsh ield mu st not b e tre ate d w ith
water -repellent materials . They can in ­
crease glare under poor v isibility condi­
tions such as wetness, da rkness, or when
the sun is low on the hor izon. In addi­
tion , they can cause the w indshield w ip­
ers to chatter.
- Properly function ing windsh ield wiper
b lades are req uired for a clea r view and
safe driving
i::> page 47, Replacing
windshield wiper blades.
(D Note
- In the case of frost, check whether the
w indshield wiper blades are fr ozen to
the windsh ield . Sw itching on the wind ­
shield wipers can damage the wiper blades!
- Pr ior to us ing a car wash, the w indshield
w iper system must be sw itched off ( lever
in posit ion 0). This he lps to prevent un in­
t en tional switch ing o n and dam age to
t he winds hield wiper system.
- Do not use the w ipers to clear a frosted
w indow. Us ing the wipers as a conve n­
ient ice scraper will destroy the wiper
blades.
(D Tips
- T he windshie ld wipers are sw itched off
w hen the ig nit io n is off . Activate the
windshield wipers after the ignition is
switched back o n by moving the w ind­
shield wiper lever to any position.

-Worn or dirty windshield wiper blades
result in streaking. This can affect the
rain sensor function. Check your wind­
shield wiper blades regularly .
- The washer fluid nozzles of the wind­
shield washer system are heated at low
temperatures when the ignition is on.
- When stopping temporarily, e.g. at a
traffic light, the set speed of the wind­
shield wipers is automatically reduced by
one speed .
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear.
Fig. 42 Removing winds hie ld w iper bla des
Service position
• Switch the windshield wipers
off (position
@ ¢page 46, fig. 41).
• Switch the ignition off and move the wind­
shield wiper lever to position @¢
page 46 ,
fig. 41.
Or
• Select in the MMI: !CAR !function button>
Car systems control button > Servicing &
checks > Wiper service position > On. The
windshield wipers move into the service po­
sition.
Removing the wiper blade
• Fold the windshield wiper arm away from
the windshield.
• Press the locking knob@¢
fig. 42 on the
wiper blade . Hold the wiper blade firmly.
• Remove the wiper blade in the direction of
the arrow.
Clear vision 4 7
Installing the wiper blade
• Insert the new wiper blade into the mount
on the wiper arm @unti l you hear it latch
into place.
• Place the wiper arm back on the windshield.
• Switch the ignition on.
• Press the windshield wiper lever.
Or • Select:
I CAR ! function button > Car systems
control button > Servicing & checks > Wiper
service position
> Off.
.&_ WARNING
- If the windshield wipers smear the wind­
shield, clean the wiper blades with wind­
shield washer fluid. If the wiper blades
are extremely dirty, you can also clean
them with a soft sponge or cloth.
- For your safety, you should replace the
wiper blades once or twice a year. See
your authorized Audi dealer for replace­
ment blades.
(D Note
-The windshie ld wiper blades must only
be folded away when in the service posi­
tion! Otherwise, you risk damaging the
paint on the hood or the windshie ld wip­
er motor.
- You should not move your vehicle or
press the windshield wiper lever when
the wiper arms are folded away from the
windshield. The windshield wipers would move back into their original position
and could damage the hood and wind­
shield .
- To help prevent damage to the wiper sys­
tem, always loosen blades which are fro­
zen to the windshield before operating
w ipers.
- To help prevent damage to wiper blades,
do not use gasoline, kerosene, paint
thinner, or other solvents on or near the
wiper blades .
- To help prevent damage to the wiper
arms or other components, do not at­
tempt to move the wipe rs by hand.