AUDI A8 2017 Owners Manual

~ Check and correc t the seating of the snow
chains after driving a few feet , if necessary . Fo l­
l ow the instructions from the manufacturer .
~ Note the maximum speed of 30 mph (SO km/
h). Note the loca l regulat ions.
Use of snow chains is on ly pe rmitted with certain
rim/tire combinations due to technical reasons.
Check w ith an authori zed Audi dealer or author­
ized Audi Service Fac ility to see if you may use
snow chains .
You must remove the snow chains on roads with­
out snow. Otherw ise, you could impair dr iving
ab ility and damage the tires.
_8 WARNING
Using incorrect snow chains o r insta lling snow
chains incorrectly can result in loss of vehicle
cont rol, which inc reases the risk of an acc i­
dent.
(D Note
- Snow cha ins can damage the rims/wheel
covers* if the cha ins come into d irect con·
tact with t hem . Remove the whee l cove rs*
f irst. Use coate d snow chai ns.
- Using snow cha ins tha t add more than 0.4
i nch (10.5 mm) of he igh t ca n seve rely dam­
age the wheel ho usings and other vehicle
componen ts .
- Do no t install and use s now chai ns if there is
a mal funct ion in the adaptive air suspe n­
s ion, because the vehicle heigh t will be very
l ow . If you drive with snow chains anyway,
the wheel ho usings and other vehicle com­
ponents can be severely damaged.
@ Tips
When using snow chains, it may be useful to
sw itch on sport mode ¢page
127.
Low aspect ratio tires
Your Aud i is factory-equipped with low aspect ra-
o tio tires. These t ires have been thorough ly tested co
~ and been selected specifically for your model for ,.....
~ their supe rb performance, road feel and handli ng 0 0 :c '<t
Wh eel s
under a var iety o f dr iv ing condit ions . Ask your au ­
thorized Audi dea le r for more detai ls.
T he low aspect rat io of t hese tires is indicated by
a nu meral o f
55 or less in the tire's si ze des igna­
tion . The n umera l represents the ratio of the
tire's sidewa ll height in relation to its tread width
expressed in percentage . Conve ntiona l tires have
a height/width ratio of 60 or more .
The performance of low-aspect- ratio tires is par­
ti cula rly sen siti ve to imprope r inflation p res­
sure. It is the refore important that low aspect
rat io tires are inflated to the specified pressure
and that the inflation pressure is regularly
checked and maintained . Tire pressures should
be checked at lea st once a month and always
before a long trip
¢ page 293 .
What you can do to avo id tire and rim
damage
Low aspect ratio tires can be damaged more eas i­
ly by impact w ith potho les, curbs, gullies or
ridges on the road, particularly if the tire is un­
der inflated .
In order to m in imize the occurrence of impact
damage to t he tires of yo ur vehicle , we recom­
me nd tha t you observe the following preca u­
tio ns:
- Always maintain recommended inflat ion pres­
sures. Check you r ti re pressu re every 2,000
m iles (3,000 km) a nd add air if necessary.
- Dr ive carefully on roads w it h potholes, deep
gullies o r ridges. The impact from dr iving
t hrough or over such obst acles can damage
your tires. Impac t with a cur b may also ca use
damage to your tires.
- After a ny impac t, im med iate ly inspect yo ur
t ires or have them inspe cted by the neares t au­
t horized A udi dealer. Replace a damaged tire as
soon as possible.
- I nspect your tires every 2,000 m iles (3,000 km)
for damage and wear. Damage is not a lways
easy to see. Damage can lead to loss of air and
underinflation, wh ich could event ually cause
tire fa ilure . If you believe that a tire may have
been damaged, replace the tire as soon as pos­
sible .
- These tires may wear more quickly than others . .,.
299

Wheels
- Please a lso remember that, wh ile these tires
deliver responsive handling, they may ride less
comfortably and ma ke more noise than other
cho ices.
Reduc ed performance in winter /cold s eason
condit ions
All tires are designed for certain purposes. The
low aspect ratio, ultra high performance t ires
or iginally i nstalled on your vehicle are intended
for maximum dry and wet road performance and
handling . They are not s uitable for cold, snowy or
icy weathe r cond itions.
If you drive under those
circumstances, you s hou ld equ ip your ve hicle
with a ll-season or win ter tires, wh ic h offe r bette r
traction under those con dit ions . We suggest you
use the recommended snow or all -season tires
specified fo r your vehicle, or their equivalent.
Refer to¢
page 298 for more deta iled info rm a­
tion regarding w in ter tires.
Uniform tire quality grading
- Tread wear
- Traction AA A B C
- Temperatu re ABC
Qua lity grades can be found where applicable on
the t ire side wall betwee n tread s hou lde r and
maximum sect io n w id th
¢pag e 283, fig. 265.
For e xample: Tread wear 2 00 , Traction AA , Tem­
perature
A .
All passenger car tires must conform to Federa l
Safety Requirements in addition to these grades.
Tread wea r
The tread wear grade is a comparat ive ra ting
based on the wear rate of the tire when tested
under contro lled conditions on a specified gov­
ernment test course.
F or examp le, a t ire graded
150 would wear one
and one ha lf
( 1 1/2) times as well on the govern ­
ment course as a tire g raded
100 .
The rela tive perfo rmance of tires depe nds upon
the actua l condi tions of their use, howeve r, and
may depart significant ly from the norm d ue to
300
variations in driving habits, service p ract ices an d
differences in road characteristics and climate.
Traction
The traction grades, from hig hest to lowest, a re
AA, A, B and
C. Those grades rep resent the tire's
ability to stop o n wet p avement as measure d un­
der controlled conditions on specified govern ­
ment test s urfaces of asphalt an d concrete. A tire
marked C may have poor traction performance
¢ _& .
Temperature
The temperature grades are A ( the highest), B,
and C, representing the tire 's resistance to the
generatio n of heat and its ability to dissipate
heat when tested under contro lled conditions on
a specified indoor laboratory test wheel.
Sustained high temperature can cause the mate­
rial of the tire to degenerate and reduce tire life,
and excessive temperature can lead to s udden
tire failure¢ &.
The grade C cor responds to a level of perform ­
ance which all passenger car tires must meet un­
der the Federal Motor Vehicle Safety Standard
No.
109. Grades Band A represent hig her levels
of performance on the laboratory test wheel than
t h e m inim um requ ired by law .
A WARNING
-
The tract io n grade assigned to this t ire is
based on st raig ht-a head b raking tr action
tes ts, and do es not in clude acceler ation, cor­
nerin g, hyd roplaning or pe ak traction ch arac­
teristics.
A WARNING
T he temperat ure grade fo r thi s tire is esta b­
lishe d for a tire that is properly inflated and
not ove rloaded. Excessive speed, underinfla -
tion, o r excessive load ing, either separately or
in comb inat ion, can cause heat bu ildup and
-
possible tire failure. ..,.

C) C0 ....
"' " "' .... 0 0 :r <t
_& WARNING
Temperature grades apply to tires that are properly inflated and not over or underinflat­
ed .
Tire Pressure Monitoring
System (AS, S8)
(D General notes
A ppl ies to: AS, 58
Each t ire, including the spare (if provided),
should be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
veh icle manufact urer on the vehicle placard or
tire inflation pressure label. (If your vehicle has
tires of a different size than the size indicated on
the vehicle placard or tire inflation pressure la­
be l, you should determine the proper tire infla­
tion pressure for those tires).
As an added safety feature, your veh icle has been
equipped with a tire pressure monitoring system
(TPMS) that illuminates a low tire pressure te ll­
tale when one or more of your tires is significant­
ly under-inflated . Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi ­
cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure. Under-inflation
also reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and stop­
ping ability .
Please note that the TPMS is not a substitute for
p roper tire maintenance, and it is the driver's re­
sponsib ility to ma intain correc t tire p ressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your veh icle has also bee n eq uipp ed w ith a TPM S
mal function indicator to indicate when the sys­
tem is not operat ing properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one mi nute and then remain cont inuously
illuminated . This sequence will continue upon
Wheels
subsequent vehicle start-ups as long as the mal ­
function exists .
When the malfunction indicator is illuminated ,
the sys tem may not be able to detect or signal
low tire pressure as intended . TPMS malfunctions
may occur for a variety of reasons, including the
i nsta llation of replacement or alternate tires or
whee ls on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replac ing one or
more tires or wheels on your vehicle to ensure
that the replacement or a lternate tires and
whee ls allow the TPMS to continue to function
properly.
If the Tire Pressure Monitoring System
indicator appears
Applies to: A8, 58
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Fig. 269 I n strument cluste r: indicator light with messa ge
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread c ircumfer­
ence and vibration characteristics of the individu­
al tires.
If the press ure changes in one or more
tires, this is indicated in the instrument cluster
display with an indicator light
[I] and a message.
If only one tire is affected, the location of that
tire will be indicated.
T he tire press ures must be stored in the Infotain­
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle
c:> page 302. The tire pressure moni­
toring system only monitors the tire pressure you have stored . Refer to the t ire pressure label for ..,.
301

Wheels
the recommended tire pressure for your vehicle
¢page 293, fig. 268.
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if:
- the tire pressure in one or more tires is too low.
- the tire has structural damage .
- the tire was replaced or the tire pressure was
changed and it was not stored¢
page 302.
-the spare tire* is installed.
Indicator lights
IE Loss of pressure in at least one tire¢&. .
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem ¢
page 302 .
mm (Tire Pressure Monitoring System) Tire
pressure: System malfunction!.
Ifmm appears
after switching the ignition on or while driving
and the
IE indicator light in the instrument clus­
ter blinks for approximately one minute and then
stays on , there is system malfunction . Try to
store the correct tire pressures¢
page 302. If
the indicator light does turn off or turns on again
after a short period of time, drive to an author­
ized Audi dealer or authorized Audi Service Facili­
ty immediately to have the malfunction correct­
ed .
A WARNING
- If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steer ing or braking maneu­
vers . Stop as soon as possible and check the
t ir es and their pressure .
- The driver is responsible for maintaining the
correct tire pressure. You must check the
t ire pressure regularly.
- Under certain conditions (such as a sporty
dr iv ing style, winter cond itions or unpaved
roads), the tire pressure monitoring system
indicator may be delayed.
- Do not use run-flat tires on your vehicle. Us­
ing them when not permitted can lead to
vehicle damage or accidents .
302
(D Tips
-The tire pressure monitoring system can al­
so stop working when there is an ESC mal­
function.
- Using snow chains may result in a system
malfunction.
- The tires with the identification "AO" or
"RO" ¢
page 290 have been matched with
your Audi tire pressure monitoring system.
We recommend that you use these tires.
Storing tire pressures
App lies to: AB, 58
If the tire pressure changes or a tire is replaced ,
it must be confirmed in the Infotainment sys­
tem.
... Make sure before storing that the tire pressur es
of all four tires meet the specified values and
are adapted to the load ¢
page 291.
... Switch the ignition on.
... Select: the
ICARI funct ion button> Car Systems
control button > Servicing & checks > Tire
pressure monitoring
> Store tire pressure >
Yes, store now.
(D Tips
Do not store the tire pressures if snow chains
are installed. Othe rw ise the system could
malfunction.
Tire Pressure Monitoring System (S8 plus)
(l) General notes
App lies to : 58 plus
Each tire, including the spare (if provided),
sho uld be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or
tire inflation pressure label. (If your vehicle has
tires of a different size than the size indicated on
the vehicle placard or tire inflation pressure la­
bel, you should determ ine the proper t ire infla-
tion pressure for those tires). .,.

0 co .... N ,..._
N .... 0 0 :c '<t
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant­ ly under-inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure. Driving on a signifi­
cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure. Under-inflation
also reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and stop­
ping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists .
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
Wheels
Description
App lies to : 58 plus
The tire pressure monitoring system monitors
the pressure in the four tires when driving .
The system uses sensors that measure the tem­
perature and pressure in the tires. The data is
sent from these sensors to the control module by
radio frequency.
The Tire Pressure Monitoring System shows the current pressures and temperatures of the tires
in the Infotainment system
o page 304. It also
compares the current tire pressures with the
stored tire pressures and gives a warning in the
driver information system if the tire pressure is
different from what is stored
o page 304.
The system does not detect if the stored tire
pressures match the recommended tire pres­
sures.
- Every time the tire pressures change, for exam-
ple when the load in the vehicle changes,
- after replacing a tire, or
- if wheels with new wheel sensors are used,
you must store the tire pressures again
opage 305.
A WARNING
--The tire pressure monitoring system assists
the driver in monitoring tire pressures. The
driver is responsible for having the tires in­
flated to the correct pressure.
- Do not change the tire pressure when the
temperature of the tire is high. This could
result in serious damage to the tire and
even cause the tire to burst, increasing the
risk of an accident.
- A tire with low pressure flexes more. This
heats the tire up too much. This could cause
the tread to separate and even cause the
tire to burst, increasing the risk of an acci­
dent.
- The Tire Pressure Monitoring System does
not warn you of damage or defects in the
tire construction that could cause the tire to
burst, for example. Inspect your tires regu­
larly.
303

Wheels
@ For the sake of the environment
Low tire pressure inc reases fuel consumption
and tire wear.
@ Tips
- The pressure of the spare tire * is not moni ­
tored.
- If t ires are re pla ced, the sensors/valves do
not need to be removed or rep laced . Ju st re­
placed the valve stem and, if necessary, the
valve and the wheel e lectron ics . If you have
quest ions, see your autho riz ed Aud i dea ler
or authorized Audi Service Facility.
Displaying tire pressures/temperatures
App lies to : 58 plus
Req uirement: the ign ition must be switched on .
.,. Select : the
ICARI function button > C ar s ystems
> Serv icing & checks > Tire pressure mon itor ­
ing
> Display tire pressures.
The current tire pressures are shown in green and
yellow numbers in the Infotainment system:
- Green : the current tire pressure and the speci­
fied tire pressure are approximately the same .
-Yellow: the c urrent tire press ure is too low
compared to the specified tire pressure.
The spe cified t ire press ure is the la st tire pres­
sure th at was s tored
c::> page 305.
No te that the tire pressure also depends on the
t emperature of the ti re . The ti re pressu re in­
creases as the engine becomes wa rmer wh ile
d riving.
& WARNING
R ea d and follow t he important information
and notes
c::> page 303 .
@ Tips
The tire pressure or tem per ature are not dis­
pl ayed in ada ptation mode. D ashe s·-.·- are
shown i n place of the press ure and tempera ­
ture .
304
-
Tire pressure loss
Applies to: 58 plus
Fig. 2 70 Dis pla y: ind icator light w it h a mess age
If the [I] ind icator light turns on, the pressure in
at least one tire is too low or new sensors were
not adapted:
RE indicator light s turn s on after turning the
ignition on
The tire pressure is too low compared to the
spec ified press ure .
.. Check and store the tire press ure(s) the next
time it is possible
c::> page 305.
RE indicator light turns on while dr iving
Wheels with new sensors we re not adapted or
the tire p ressure has reached a critica l level com­
pared to the specif ied pressure.
.. Avoid unnecessary s teering and brak ing maneu-
vers .
.. Adapt your driving sty le to the s ituation.
.. Stop as soon as possib le and check the tire(s).
.. If it is possib le to cont inue dr iv ing, see an au-
thorized Audi dealer or authorized Audi Service
Facility immediately and have your tire(s) re ­
pai red or rep laced .
& WARNING
Read and f ollow the impo rtant inform ation
and notes
c::>p age 303.
-

Storing new tire pressures
Applies to: S8 plus
Correctly stored tire pressure specifications are
necessary for reliable tire pressure monitoring .
.. Check the tire pressures in all wheels.
1> If necessary, correct the tire pressure according
to the spec ificat ions on the sticker on the driv ­
er's door ~
page 291 . Only correct the press ure
in tires whose tempera tu re is approx imately
the same as the amb ient temperature.
If the
tempera ture of the tire is highe r than the ambi­
ent a ir temperat ure, the tire pressure must be
increased approximately 3 PSI (0,2 bar) above
the va lue on the sticker.
.. Switch the ignition on.
.. Se lect :
I CARI funct ion button > Car systems >
T ire pr essure monitoring > Store tire pres­
s ure s.
After stor ing, the tire pressure mon itor ­
ing system measures the c urrent tire pressures
and stores them as the new specified p res­
s ur es .
.. If the changed tire press ures are not displayed
in t he Infotainment system, dr ive the veh icle
for approximate ly 10 minutes so that the sen ­
sor signal from the whee ls is received again .
During this adap tat ion phase, --,-- is disp layed
for pressure and temperature and the Tire Pres ­
sure Monitoring System is only partially availa­
b le: it only warns you if one or more of the tire
pressures is/are under the m inimum permitted
va lue. If this is the case, the
It] indicator light
appears w ith a message .
A WARNING
Read and follow the important information
and notes
~ page 303.
Malfunctions
Applies to: S8 plus
-
I f t he Tire Pressu re Monito ring System is not
av ail able,
the m ind icator light appe ars in the
driver informat ion system. The
HJ] indi cator light
o a lso blinks for approx imately one m inutes each co
~ time the ignition is switched on . The tire pressure ,.....
~ monitoring system cannot be selected in the In-o 0 :c '<t
Wh eel s
fota inment system. The following are examp les
of situations that cou ld cause a malfunction:
- I f the message appears at t he e nd of the adap­
t ation phase, the system cannot detec t the
wheels installed on the veh icle. This may result
from one or more whee ls being installed with­
out wheel senso rs or with incompatible whee l
sensors.
- A wheel sensor or another component has
fa iled.
- Using snow chains can affect the function of
the system beca use of the shielding effect of
the chains .
- The tire pressure monitoring system is not
avai lab le due to a ma lf u nction .
- Transmitters with the same frequency, such as
headphones or remote-cont rolled devices, may
cause a temporary system malfunct ion due to
the strong electromagnetic field.
The
fim indicator light t urns off once the Tire
Pressure Monitoring System is availab le aga in . If
you cannot correct the ma lf u nction and
the m
indicator light stays on, drive immediately to an
authorized Aud i dealer or a uthorized Audi Serv ice
Facility to have the malf unct ion repaired .
305

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value.
It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The necessary care products can be obtained
from an authorized Audi dealer or authorized
Audi Service Facility. Read and follow the instruc­
tions for use on the packaging.
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health .
- Always store cleaning and care products out
of reach of children to reduce the risk of poi­
soning.
@ For the sake of the environment
- Preferably purchase environmentally-friend­ ly cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve­ hicle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect .
Before washing, rinse off heavy deposits with
plenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
Also, wash the underside of your vehicle once road salt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash ­
er, always follow the operating instructions pro­
vided with the pressure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at the
306
seals on the side windows, doors, lids or the sun­
roof* or at tires, rubber hoses, insulating materi­
al, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozzles or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °C).
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshield wipers are off . Follow instruc­
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Only use car washes where the veh icle remains
stationary and the washing equipment moves
around the vehicle when washing and drying. Car
washes that move the vehicle through the car
wash using a chain are not recommended.
Washing by hand
Clean the vehicle starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint.
Apply the product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft micro­
fiber cloth .
Rinse the vehicle thoroughly again and let it air
dry. Remove any water residue using a chamois. ..,..

0 co .... N ,..... N .... 0 0 :c '<t
& WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the braking effect
may be delayed due to moisture on the
brake rotors or ice in the winter . This in­
creases the risk of an accident . The brakes
must be dried first with a few careful brake
applications.
(D Note
- If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Power folding exterior mirrors* must only
be folded in and out using the power folding
function.
- To reduce the risk of paint damage, do not
wash the vehicle in direct sunlight.
-
Care and cleaning
-To reduce the risk of damage, do not wash
the power top with a pressure washer.
- To reduce the risk of damage to the surface,
do not use insect removing sponges, kitchen
sponges or similar items.
- Matte finish painted vehicle components:
- To reduce the risk of damage to the sur-
face, do not use polishing agents or hard
wax.
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint . The paint could be damaged
when the stickers or magnets are re­
moved.
@ For the sake of the environment
Only wash the vehicle in facilities specially de­
signed for that purpose . This will reduce the
risk of dirty water contaminated with oil from
entering the sewer system.
Cleaning and care information
When cleaning and caring for individual vehicle
components, refer to the following tables. The
information contained there is simply recom­
mendations. For questions or for components that are
not listed , consult an authorized Audi
dealer or authorized Audi Service Facility. Also
follow the information found in¢& .
Exterior cleaning
Component Situation Solution
Windshield wiper
Deposits ¢ page 51
blades
Headlights/
Deposits Soft sponge with
a mild soap solutiona)
Tail lights
Sensors/
Deposits Sensors: soft cloth with solvent-free cleaning solution
camera lenses Camera lenses: soft cloth with alcohol-free cleaning solu-
tion
Snow/ice Hand brush/solvent-free de-icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
307

Care and cleaning Component Situation Solution
Exhaust tail pipes
Road salt Water, cleaning solution suitab le for stainless steel, if nee-
essary
Decorative parts/ Deposits Mild
soap solution a), a cleaning solution suitable for stain-
Trim less stee l, if necessary
Paint Paint damage Refer to th e paint number on the vehicle data label, repair
with touch up paint ~
page 333
Spilled fuel Rinse
with water immediately
Surface rust Rust remover, then protect with hard wax; for questions,
consult an author ized Audi dealer or authorized Aud i Serv-
ice Facility.
Corros ion Have it removed by an authori zed Aud i dea ler or author-
ized Audi Service Facility.
Water no longer Pr
otect wi th hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat wit h suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen with water immediately and remove with a micro-
sects, bird dropp ings, f iber cloth
tree sap and road salt
Grease-based con- Remove immediately with a mild soap solution a ) and a
taminants such as soft cloth
cosmetics or sunblock
Carbon parts Deposi ts clean the same way as painted parts ~ page 306
a) Mild soap so lution: maxim um two tabl espoo ns of n eu tra l s oap in 1 quart Cl lite r) of w ater
Interior cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild soap
solution al
Trim
Plastic parts
Deposits Damp clo1th
Heavier deposits Mild soap solution
al, detergent-free pla stic clean ing solu-
tion, if necessary
Displays Deposits Soft cloth with LCD cleaner
Controls Deposits Soft brush, then
a soft cloth with a mild soap so lution al
Safety belts Deposits Mild soap solution al, allow to dry before letting them re-
tract
308
...