AUDI Q3 2015 Owners Manual

M N M N
0 :::i co
rl I.O
"' rl
"' rl
@ Tips
- The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump start ing or charging the
battery, never connect the negative
ground cable to the battery negative post because the battery manager sys­
tem must be able to detect the battery's
state of cha rge . A lways connect the neg­
ative g round cab le to the negative
gro und post o f the battery manage r con­
trol uni t.
Use of jumper cables
Make sure to connect the jumper cobl e
clomps in exactly the order describ ed b elow!
F ig. 171 Engine co mpartmen t: Con ne ctors fo r jum per
c ables a nd char ger
Fi g. 172 Jump s tart in g w ith t he ba ttery of a not her ve ­
hi cle :@ disch arged vehicle battery ,@ booster bat tery
The procedure described below for connecting
jumper cables is intended to provide a jump
start for your veh icle .
V ehicle with discharged batter y:
.. Tu rn off lights and accessories, move lever
of automatic transmission to N (Neutral) or P (Park) and set parking brake .
Emergency situ ation s 229
Connect POSITIVE(+ ) to POSITIVE (+ )
(red )
.. To access the positive terminal, remove the
battery cover
c::> fig. 1 71.
1. Connect one end of the red positive cable
on the
jump sta rt bolt (D c::> fig . 172 (Bolt
under cover = "positive") of the vehicle to
be started @.
2 . Connect th e other end to the pos itive ter-
mina l@ of the booster battery @.
Connect NEGATIVE( -) to NEGATIVE(-)
( black )
3. Connect one end of the black negative ca­ ble to the negat ive termina l@ of the
booster battery @.
4 . Connect the othe r end to the
jump start
bolt @
(Bolt with hex head = "negative")
of the vehicle to be started @.
Starting the engine .,. Sta rt the engine of the veh icle w ith the
booste r ba tte ry @ . Ru n the engine at a
moderate speed .
.. Start engine w it h discharged vehicle battery
@ in the usual manner .
.. If the eng ine fails to start: do not keep the
starter c ranking for longer than 10 seconds.
Wait for about 30 seconds and the n try
aga in .
.. With eng ine runni ng, remove jumpe r cab les
from both vehicles in the exact
reverse o r­
de r .
.,. Fit the cover b ack o nto the battery.
T he battery is vented to th e outside to p revent
gases from enter ing the veh icle inter io r. Ma ke
s u re that the j umper clamps are well connec t­
ed with their
metal parts in full contact with
the battery term inals.
,8. WARNING
To avoid serious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable man ufac­
turer. If in doubt, call for road service .
- J umper cables m ust be long enough so
that the veh icles do not touch.
-

230 Emergency sit uat ions
-When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the eng ine compart­
ment.
- Do not bend over the batteries - danger
of chemical burns!
- The battery cell locking screws must be tightened securely.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
r=>page 179.
Improper hook-up of jumper cables can r u­
in the generator.
- Always connect POSITIVE( +) to POS I­
TIVE(+), and NEGATIVE( -) to NEGATIVE
(-) ground post of the battery manager
control unit.
- Check that a ll screw plugs on the battery
cells are screwed in firmly. If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
nect ing a jumper cable as described
above applies spec ifically to the case of
you r vehicle being jump started. When
you are givi ng a jump start to a nothe r ve­
hicle, do
not connect the negat ive (-) ca ­
ble to the negat ive (-) term inal on the
discharged battery @r=>
fig. 172. In ­
stea d, securely connect the negative( -)
cable to e ithe r a solid metal component
that is firm ly bolted to the engine block
or to the engine block itse lf. If the bat­
tery that is being charged does not vent
to the outside, escaping battery gas
could ignite and exp lode!
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow truck operators who know
how to operate their equipment safely.
- Ne ver tow your Audi , towing will cau se
damage to the engine and transmi ssion .
- Ne ver wrap th e safet y chains or winch ca­
ble s around the brak e lines.
- To prevent unne cessar y damage, your Audi
must be tr an sp o rted with a flat bed tru ck.
- To load th e vehi cle on to the fl at bed, use
the towing l oop found in the ve hicle to ols
and atta ch to th e front or rea r anchorage
r=> page 231 and Qpage 231 .
& WARNING
= -
A vehicle being towed is not safe for pas-
sengers. Never allow anyone to ride in a
vehicle being towed, for any reason.

M N M N
0 ::i co
rl I.O
"' rl
"' rl
Front towing loop
Do not install the front towing loop until it is
needed.
Fig. 1 73 Fro nt bumper : Remov ing th e cover
Fi g.17 4 Fron t bumper: S crew ing in the tow ing loo p
The screw connection for the towing loop is
l ocated behind a cove r on the right side of the
front bumper.
"' Take the towing loop and the hook out of
the vehi cle too l kit
c:::> page 216 .
"'Inse rt the hook into the ho le in the cover
and carefully pu ll the cove r off in the direc­
tion ind icated
<=:> fig . 173.
"' Screw the towi ng loop tight ly into the
threaded hole as far as it will go
c:::> fig. 174
and t ighten it w ith the wheel wrench .
When it is no longer needed, unscrew the
towing loop and put it back into the veh icle
too lkit . Be sure to have the tow ing loop stored
in the vehicle at all times.
When re-insta lling the cover be s ure to first
insert the tabs on the cover into the retainers
near the radiator gri lle . Then insta ll the other
side of the cover and push it into the retainers
¢ fig . 173 .
The appearance of the cover varies from the il­
l ustration for some model versions.
Emergenc y situ ation s 231
A WARNING
If t he tow ing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed -potent ia l risk of an
accide nt.
(D Note
The cover is attached to the bumper with
several hooks . Do not use excess ive force
when remov ing t he cover to avoid damag­
i ng it.
Rear towing loop
On vehicles without a factory -installed trailer
hitch*, the threaded hole for the towing loop
is on the right side of the rear bumper.
0
Fi g. 17S Rear bumper: Cov er cap
0
F ig . 1 76 Rea r bumper: Sc rew ing in tow ing loop
V ehicles with a towing loop
"' Take the towi ng loop out of the vehicle tool
ki t
c:::> page 216.
"' Press the cover in by app lying short strong
pressure to the bottom part to release it
from the bumper
c:::> fig. 175.
"' Screw the towing loop t ightly into the
threaded ho le as far as it w ill go
¢ fig. 176
and tighten it with the wheel wrench. Ill>

232 Emergency situations
Vehicles with a trailer hitch*
.,. In stall the trailer h itch .
.,. Attach the towing bar or the towing cab le to
the trai ler hitc h.
Unscrew the towing loop agai n after use and
i nsta ll t he
cover in the b umpe r. Re tur n t he
towing loop to t he vehicle too lkit. Be sure to
have the towing loop stored in the vehicle at
a ll t imes.
A WARNING
- If the towing loop is not screwed in as far
as it will go, t he thread can pull out when
the vehicle is towed -potential risk of an
acc ident.
- If your veh icle has
a trailer hitch* on ly
use a specia l towing bar to p revent dam ­
aging the ball h itch . Th ese towing bars
have been specially designed for trailer
t owing hitches.
- If your veh icle has a
trailer hitch* use on­
ly specia l towing cables .
Loading the vehicle onto a flat bed truck
Fig. 17 7 Veh icle on flat bed truck
F ront hook up
.,. Align the vehicle with the centerline of the
car carrier ramp .
.,. Attach the winch hook to the front towline
eye previously insta lled .
Rear hook up
.,. Align the vehicle wit h the centerline of the
car carr ier ramp.
.,. Attach the winch hook to the rear towline
eye previously installed.
(D Tips
Check caref ully to make sure t he hook -up
i s secure before mov ing the car up t he f lat­
b ed truck ramp .
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may only be lifted at the lif ting
points illustr ated.
Fig. 17 8 Front lift ing point
Fig . 17 9 Rear liftin g po int
.,. Read and heed WARNI NG c::> .&_ .
.,. Locate lifting points c> fig. 178 and
c>fig. 179 .
.,. Adjust lifting arms of workshop ho ist or
floor jack to matc h ve hicle lift ing po ints .
.,. Insert a rubber pad between the floor jack/
workshop hoist and t he lift ing points .
If you must lift your vehicle with a floor jack
to work undern eath, be su re the vehicle is
safely supported on stand s intended for this
purpo se .
Front lifting point
The lifting poi nt is located on the floor pan re-
i nforcement abo ut at the same level as the
II>

M N
M N
0 ::i co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
jack mounting point ¢ fig. 178. Do not lift
the vehicle at the vertical sill reinforcement.
Rear lifting point
T h e lift ing poin t is lo cate d on th e vertical rein ­
fo rc ement o f the lower s ill for th e on boar d
jack
r::!vfig. 1 79 .
Lifting with vehicle jack
Refe r to ¢ page 221 .
A WARNING
- To reduce the r is k o f se rious injury a nd
vehicle damag e.
- Always lift the ve hicle on ly at the spe­
cial w ork shop h oist and flo or jack lift
points illustrated
¢ fig. 178 and
¢fig. 179 .
-Fai lure to lift the vehicle at these
poi nts cou ld cause the ve hicle to tilt or
fa ll from a lift if the re is a chang e in ve­
h icl e w eigh t distr ibu tion and balance.
This might happen, for e xam ple, w hen
heavy co mpo ne nts su ch as the engi ne
b lo ck or tra nsmi ssion ar e removed .
- W hen removing heavy comp onents like
th ese, a nch or ve hicle to hoist or add cor­
resp ond ing weig hts to maintai n the cen­
ter o f gravity . Othe rwise, the vehicle
mig ht tilt or s lip off the hoist, causi ng
serious persona l injury .
(D Note
- Be aw ar e of t he fo llow ing poin ts be fore
lift ing t he vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the
front or rear axle or the body side members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points .
- Before driving over a workshop hoist,
check that the vehicle weight does not
-
Emergency situations 233
exceed the permissible lifting capacity
of the hoist .
- Before driving over a workshop hoist ,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.
•
•

234 Technical Data
Technical Data
Vehicle identification
Fig . 180 Location on driver 's s ide dash pane l: Vehicle
Identifica tion Numbe r (V IN) p la te
XXXXX XX · X -XXXX XXX xx
r,'\__l f~ -11!11 1 · Nil ~ V!Hlll -llllll . NO.
IYP IT'fl'E
XXXXXXXX XX X XXXXXXXX
XXX XXX
XX XXXX XXX X X X X XX
XXX
KW XXX
®i ~~: f :l~~ XXXX XXX XXX
@+ ~~r= XXXX I XXXX XXX I XX M,. AIIISl. / lflllllS
EO A 7D5 4 UB 6XM SSG 5RW
2E H JDZ llB l AS lBA
3FC 5MU 7X l
FO A
9G3 OG7 OYH OJF
TL6 3
KA BEH
UlA X9B QZ7
l XW
8Q3 9Q8 82 4 020
7T6 CV 7 7KO 4X3 2K2
3 L4 4 KC 3YO 4I3 502
lSA 7GB Q1 A 4GQ
XX X
XX X XX X XXXX
Fig. 181 Inside the luggage compartme nt: Vehicle
i dentifica tion label
Vehicle Identification Number (VlN)
The Vehicl e Identification Number is located
in different p laces :
- under the w indshield on the driver's side
r=v fig . 180.
-in the radio or in the MM!": !CAR ! function
button
> Car"systems control button > Serv­
icing
& checks > VIN number.
- on the vehicle identification label.
Vehicle identification label
The vehicle identification label is located in
the luggage compartment near the battery . T
he label
r=v fig. 181 shows the following vehi­
cle data:
(D Vehicle Ident ificat ion Number (VIN)
@ . Vehicle type, engine output, transmission
® Engine and transm ission code
@ Paint number and interior
® Optional equipment numbers
The information of the vehicle identification
label can also be found in your Warranty
&
Maintenance booklet.
Safety compliance sticker
The safety compliance sticker is your assur­
ance that your new veh icle complies with all
applicable Federal Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured. You can find this
sticker on the door jamb on the driver's side.
It shows the month and year of production
and the vehicle ident ificat ion number of your
vehicle (perforat ion) as well as the Gross Veh i­
cle Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine
hood re lease . The spark ignition sys tem com­
plies with the Canadian standard IC ES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rat ing (GAWR) for
front and rear are listed on a sticker on the
doo r jamb on the driver's s ide .
The Gross Vehicle Weight Rating includes the
weight of the bas ic vehicle plus fu ll fuel tank,
o il and coolant, plus max imum load, which in­
cludes passenger weight (lSO lbs/68 kg per
designated seating position) and luggage
weight ~&, . .,.

M N
M N
0 ::i co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Gross Axle We ight Rating
The G ross Axle Weight Rating is the maxim um
l oad that can be applied at each axle of the
vehicle
c::> &. .
Vehicle capacity weight
The vehicle capac ity we ight (max. load) is list­
ed on the d river 's side 8-p illar.
Roof weight
The maximum perm iss ible roof we ight is
165 lb (75 kg ). The roof weig ht is the total of
the we ight of the roof rack, the attachments
a nd the cargo you are carrying.
.8, WARNING
- T he ac tual Gross Axle Weight Rat ing at
the front and rear axles sho uld not ex­
ceed the permissi ble weights, a nd their
combination must not exceed the Gross
Vehicle Weight Rat ing.
- Exceeding permissib le we ight ratings can
result in vehicle damage, accidents and
persona l injury.
(D Note
- The vehicle capacity weight figures apply
when the load is distrib uted evenly in the
vehicle (passengers and luggage). When
transpo rting a heavy load in the l uggage
compartment, carry the load as near to
the rea r axle as possib le so that the ve hi­
cle's handling is not impa ired.
- Do n ot exceed the maxim um permissible
axle loads o r the maximum gross vehicle
weig ht. Always rememb er that the ve hi­
cl e's ha ndling will be affected by t he ex­
t ra load. T herefore, adjust you r speed a c­
c or dingly.
- Always obse rve lo ca l regu lations.
Dimensions
Length in (mm) 172.6 (4385)
Width in (mm) 72
.1 (1831)
.
Techni cal Dat a 235
Widt h (ac ross mir- in (mm) 79.5 (
2019)
rors)
H eight (unload- in (mm)
62.6 ( 1590)
ed )a)
a) The height of the vehicle depends on the t ires and the
s u spension.
When dr iving up steep ramps, on rough roads,
ove r cu rbs, etc. it is important to remember
t h at some parts of you r vehicle, such as spo il­
ers o r exha ust sys tem components, may be
cl ose to the g ro und. Be carefu l not to dam age
them.
Capacities
Fue ltank:tota lca- gal ( lit-16.9 (64.0)
pac ity ers)
Windshield washe r
quarts
4.8 (4.5)
fluid container (liters)
•
•

236 Technical Dat a
Gasoline engines
Q3 2.0, 4 cylinder
Maximum output SAE net hp@rpm 200@ 5100-6000
Max imum torque SAE net Lb-ft@ rpm 207 @ 1700-5000
Displacement CID (cm
3
) 121 (1984)
Engine oil with filter change quarts (liters)
4.9 (4,6)
Fuel
Pr em ium un leaded (9 1 A KI) ¢ page 175, Caso-
line

M N
M N
0 ::i co ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
Consumer Information
Warranty coverages
Your Audi is covered by the following war­
ranties :
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Con trol Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warran ­
ties can be found in your
Warranty & Mainte­
nance booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A. and Canada differ from vehicles sold in
other countries .
If you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that:
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lower octane
rating . Improper fuel may cause engine
damage ;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment;
- replacement parts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessari ly work
in Europe, and may not work in other coun­
tries outside of North America.
Consumer Information 237
@ Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, service or parts availab ility.
Audi Service Repair
Manuals and Literature
Audi Offic ial Factory Service Manuals and Lit ­
erature are published as soon as possible after
model introduction. Service Manuals and liter­
atu re are availabl e to order from the Audi
T echnical Literature Ordering Center at:
www.audi.techliterature.com
Maintenance
' General
Your vehicle has been designed to help keep
maintenance requirements to a minimum.
However, a certain amount of regular mainte­
nance is still necessary to assure your vehicle's
safety, economy and reliability . For detailed
vehicle maintenance consult your Warranty
&
Maintenance booklet.
Under difficult operating conditions , for ex­
ample at extremely low outside temperatures ,
in very dusty regions, when towing a tra iler
very frequently, etc., some serv ice work
shou ld be pe rformed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or replacing the air filter .
® For the sake of the environment
By regularly maintaining your vehicle, you
help make sure that emission standards
are maintained, thus min imizi ng adverse
effects on the environment .
Important considerations for you and
your vehicle
The increasing use of electronics , sophisticat­
ed fuel injection and emission contro l sys-
tems, and the genera lly increasing technica l ..,_
•
•

238 Con sum er Inf ormation
comp lexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, s afety an d e nvir onm ent al con­
cerns place very strict limits on the nature of
repairs and adjustments to engine and trans ­
miss ion pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure proper
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­ ranty. Therefo re , proof of servic ing in accord­
ance w it h the ma intenance sched ule may be a
condition for upholding a possible warranty
claim made within the warran ty period.
Above all, operational safety can be adve rsely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any serv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop .
We strong ly urge you to give your authorized
Audi dealer the opportunity to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and tra ined spec ialists to keep your vehicle
running properly .
Performing lim it e d m aint en anc e y ourself
The fo llowing pages describe a limited num­
ber of procedures which can be performed on
you r vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and ca refully follow the instruc­
tions given. Always rigorously obse rve the
WARNINGS p rovided .
Before you ch eck anything in th e engin e
compartme nt, alway s read an d heed all WARNINGS
¢.&. and
¢ .&. in Working in the
engine comportment on page 179 .
A WARNING
--Serious personal injury may occur as a re-
sult of improperly performed mainte­
nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r isk personal
in jur y.
- Do not attempt any of the maintenance,
checks or repairs descr ibed o n the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re­
spect to the ve hicl e, or are uncerta in how
to proceed .
- Do not do any work withou t the proper
too ls and equipment . Have the necessary
work done by your authorized A udi deal ­
er or anothe r properly equipped and
qualified workshop.
- The engine compar tment o f any motor
vehicle is a potentially hazardous area. Never reach into the area around or
touch the rad iator fan. It is temperature
control led and can sw itch on suddenly -
even when the engine is off and the igni­
tion key has been removed. The rad iator
fan switches on automatically when the coo lant reaches a certai n tempera ture
and will cont inue to run until the coo lant
temperature drops .
- Always remove the ign ition key befo re
a nyone gets under the veh icle.
- Always suppor t your veh icle with safety
s tands if it is necessary to work under­
neath the vehicle. The jack* s upplied
with the vehicle is not adequate for this purpose and could co llapse causing seri­
ous personal injury .
- If you must work unde rneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are always securely blocked and that the engine cannot be
started.