ECO mode AUDI Q3 2015 Owners Manual

14 Instrum ent s and w arn ing /indic ato r light s
(USA models): If the warning light . and the
warning light
ll] appear together, immedi­
ately contact your authorized Audi dealer or
qua lified workshop to have all brake pads in­
spected
¢ page 17.
When the light comes on, an audib le warning
signal is also given .
.&_ WARNING
- Always observe the warnings in
¢ page 179, before opening the hood
and checking the brake fluid.
- Driv ing with low brake fluid is a safety
hazard. Stop the car and get professional
assistance.
- If the . (USA models) . (Canada
models) brake system indicator light
turns on together with the ABS and ESC
indicator lights, the ABS/ESC regu lating
function may have failed. Functions that
stabilize the vehicle are no longer availa­
ble. Th is could cause the vehicle to
swerve and increase the risk of sliding .
Drive carefully to the nearest a uthorized
Audi dealer or other qualified workshop
and have the malfunction corrected.
- If the brake warning/indicator light does
not go out after a few seconds and the
park ing brake is released, or lights up
wh ile you are driving, the fluid level in
the brake fluid reservoir is too low .
If you
believe that it is safe to do so, proceed
immediately at low speed to the nearest
authori zed Audi dealer o r qualified wo rk­
shop and have the bra ke system inspect­
ed.
- Always keep in m ind that after several
brake applicat ions, yo u will need greater
pressure on the brake peda l to stop your
vehicle. Do not re ly on strained brakes to
respond with maxim um stopping power
in critical situations. You must allow for
increased brak ing distances. The extra
distance used up by fad ing brakes could
lead to an acc ident.
PARK !<®> Electromechanical parking brake
The warning/indicator light monitors the
electromechanical parking brake .
If the indicator light. (USA models) •
(Canada models) turns on, the parking brake
was set.
• (USA model s)/. (Canada models ) Press
brake pedal to release parking b ra ke.
To re lease the park ing brake, press the brake
peda l and press the button(®) at the same
t ime or start driving with starting assist
¢ page 71, Starting from rest.
Ill Pa rking br ake : S ys tem f ault! See owne r's
manual.
If the I.II ind ic a tor light tu rns o n and this
message appears, there is a parking b rake
malfunction. Drive to your authorized A udi
dealer or qualified workshop immediately to
have the malfunct ion corrected.
@ Tips
More informat ion on the parking brake
¢page 70 .
-L Engine cooling system
A malfunction in the engine cooling system
must be repaired as soon as possible.
• Turn off engine and ch eck coolant level
T he coolant level is too low .
Do not continue dr iving and turn
off the en­
gine. Check the coo lant level
¢ page 186.
-If the coo lant level is too low, add coo lant
¢ page 186. Only continue driving if the in­
dicator light turns off.
- If the coo lant level is correct, then the ma l­
function may be ca used by fa ilure of the
coolant fan. Do not continue driving. See
your authorized Audi dealer or qualified re­ pa ir fac ility .
• Coolant temperature! Let engine run
w ith vehicle stationar y.

16 Instruments and warning/indicator lights
~ Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The. warning/indicator light illuminates
when the ignition is sw itched on to remind
the dr iver and any front passenger to put on
the safety belt. Additionally, an acoustic warn­
ing (gong) will also sound.
(D Tips
For more Information c> page 104, Safety
belt warning light.
~- Steering column lock
• Steering fault! Do not drive vehicle!
If the indicator light turns on and the mes­
sage appears, there is an electronic steering
column lock malfunction. You cannot switch
the ign ition on.
Do
not tow your vehicle because it cannot be
steered . Seek professional assistance.
Ill Steering lock: System fault! Please con­
tact dealer.
If the indicator light turns on and the mes­
sage appears, there is an electronic steer ing
column lock malfunction.
Drive to your authorized Audi dea ler immedi­
ate ly to have the malfunction corrected .
A WARNING
-
Your vehicle must not be towed in the
event of a malfunct ion in the electron ic
steering column lock because it cannot be
steered due to the locked steering. If it is
towed with the steering locked, there is
the risk of an accident .
!;.IC; Electronic Stabilization Control
(ESC)
If the J;J indicator light blink s whi le driving,
the ESC or ASR (Anti-S lip Regulation) is active­
ly regulating .
If the: JjJ indicator light turns on, the system
has switched the ESC
off. In this case, you can
switch the ign ition
off and then on to switch
the ESC on aga in. The indicator light turns
off
when the system is functioning fully.
If the II indicator light turns on, ESC was re­
stricted or sw itched
off using the I~ OFFI but­
ton
i=> page 153.
Stabilization control (ESC/ABS): Fault! See
owner's manual
If the indicator l ight GJ and the ABS indicator
light
t1l1 (USA mode ls) ;tiJ (Canada models)
tu rn on and the message appears, the ABS o r
electronic differentia l lock is malfunctioning.
This also causes the ESC to malfunction. The
brakes still function with their normal power,
but ABS is not active.
Drive to your authorized Audi dealer immedi­
ate ly to have the ma lfunction corrected.
A WARNING "--
If the . (USA mode ls)/ . (Canada mod-
e ls) brake system indicator light turns on
together with the ABS and ESC indicator
lights, the ABS/ESC regulating function
may have failed. Functions that stabilize
the vehicle are no longer ava ilable. This
could cause the vehicle to swerve and in­
crease the risk of slid ing. Drive carefully to
the nearest authorized A udi dealer and
have the ma lfunction corrected.
(D Tips
For additional informat ion on ESC and
ABS, refer to
c> page 153.
!t Safety systems
The fll indicator light monitors the safety
systems (e .g. airbags, pretensioners) and illu­
minates for a few seconds each time you
switch the ign ition on .
If the
fll indicator light does not go out, or if
it illuminates while you are driving, or if it
starts to b link, then there is a malfunct ion
somewhere in the system. If the light does

M N M N
0 ;::::, co
rl I.O
"' rl
"' rl
Time and date display
Fig. 9 Dis pl ay: time an d date
Depending on the veh icle equ ipment leve l,
you may choose between the quartz clock or
the GPS control led clock*
l!j . You can learn
more about this in the MMI manual or in the
radio user's ma nua l.
(D Tips
- When you switch off the ign ition or open
the driver door, the time, date, odome­
ter and temperature are disp layed for an
additional 30 seconds.
- You can also call up the display w ith the
I SET I b utton (D ~ page 10, fig . 3 while
the ignition is switched off.
Odometer
F ig. 10 Dis play : odomete r
Odometer /trip odometer
The display of distance driven is shown in kilo­
meters "km" or in miles "mi" .
- USA mode ls - Miles
- Canada models -Kilometers
The uni ts of me asure (kilometers/miles) can
be changed in the rad io or MMI*. You can
Dri ver inform ation di spl ay 23
learn more about this in the MM I manual o r in
the radio use r's manual.
T he odometer @shows the total number of
k il ometers o r miles that have been dr iven on
the vehicle.
The trip odometer @ shows the d istance driv­
en since it was last reset . It can be used to
measure short distances. The last d igit shows
distances of 100 meters or 1/10 of a mi le.
The trip odometer can be reset to zero by pressing the reset button I
0.0 I @ ~ page 10,
fig. 3.
Malfunction message
If there is a malfunct ion somewhere in the in­
strument cluster,
DEF w ill appear in the trip
odometer and w ill stay on . Contact your au­
thorized Aud i dea le r to have the prob lem cor­
r ected .
Open door/hood/rear
lid warning
F ig. 1 1 Dis play : door o pen
0
"' N 9 ::::, 0:, a,
With the ign ition sw itched on, the warn ing il­
luminates when at least
one door o r the hood
or the rear l id is not closed . T he symbo l also
shows you
which door(s) or lid is not closed.
In the illustration
~ fig . 11 it is the front pas­
senger · s door.

40 Clear vision
Clear vision
Lights
Switching the lights on and off
Fig . 34 Instrument panel: headlight control switch
Light switch -'t;. -
Tu rn the switch ¢ fig. 34 to the corresponding
position. When the lights are switched on, the
:oo : symbol turns on.
0 -The lights are off or the daytime running
lights are on:
- USA models: The daytime running lights are
activated when the light switch¢
fig. 34 is
in the
O position or the AUTO position (only
in daylight conditions). The daytime running
lights function can be turned on and off in
the radio or
MMI* menu Exterior lighting
¢ page 42, ¢ ,& .
-Canada models : The daytime running lights
are activated when the light switch¢
fig. 34
is in the O posi tion, co o: position or the AUTO
position (only in daylight conditions). The
dayt ime running lights function cannot be
turned off¢,& .
AUTO* -Automatic headligh ts swi tch on and
off depending on brightness, for example in
twilight, during rain or in tunnels¢,& .
:oo: -Side marker lights
io -Low beam headlights
Fog lights /rear fog lights
[!Q] -Fog lights. Turn the light switch to :oo:
(side marker lights) or io (low beam head­
lights). Then pull the light switch out to the
first position ¢
fig. 34.
@I] -Rear fog lights. Turn the light switch to
:oo : (side marker lights) or io (low beam head­
lights). Then pull the light switch out to the
second position .
Headlight range control system
The headlight range adjusts automatically
when there is a change in veh icle load and
during braking and accelerating so that the
headlights do not cause glare for oncoming
traffic.
Adaptive light*
The adaptive light only functions when the
switch is in the AUTO position (Automatic
headlights). When switched on, adapt ive light
adapts to curves in the road depending on the
vehicle speed and the steering angle. This pro­
vides better lighting through the curve . The
system operates at speeds between approxi ­
mately 6 mph (10 km/h) and 68 mph
(110 km/h) .
_&. WARNING
- Daytime running lights and automatic
headlights* are only intended to assist
the driver. They do not relieve the driver
of his responsibility to check the head­
lights and to turn them on manually ac­
cording to the current light and visibility
conditions. For example, fog cannot be
detected by the light sensors*. So always
sw itch on the headlights
io under these
weather conditions and when driving in
the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists. Always turn on
the headlights so that you can see ahead
and so that others can see your car from
the back.
- Please obey all laws when using the
lighting systems described here.
(D Note
The rear fog lights should only be turned
on in accordance with traffic regulation, as
-
the lights are bright for following traffic. .,._

M N M N
0 ::i co
rl I.O
"' rl
"' rl
light switch is in the AUTO position
¢ page 40, fig. 34.
Daytime running lights
USA models : You can switch the dayt ime run­
ni ng lights
on an d off .
Canada models:
The function cannot be
turned off .
It is ac tiva ted automat ica lly each
time the ignition is switc hed o n.
Emergency flashers
Fig . 3 7 Cente r conso le : emerge ncy flashe r sw itch
The emergency flashers makes other moto­
rists aware that you or your vehicle are in an
emergency situation .
.,. Press the sw itch
Gil ¢ fig. 3 7 to turn the
emergency flashers on or off.
When the emergency flashers are on, all four turn signals blink at the same time. The turn
signa l ind icator lig hts
II 18 in the instru­
ment cluster, as well as the light in t he emer ­
gency flashe r switch
[Ai bli nk likewise .
You can indicate a lane change or a turn when
the emergency flashers are switched on by us­
ing the tu rn signa l lever . The emergency flash ­
e rs stop temporar ily.
The emergency f lashers also work when the
ignit io n is turned off.
The emergency flashers will turn o n automati­
cally if you are in an accident where the airbag
h as dep loyed.
@ Tips
You shou ld t urn on t he emergency flashers
when:
Clear vi sion 43
- yo u are the la st veh icle standing in a t ra f­
fic jam so that any other ve hicles coming
can see you, o r whe n
- yo ur vehicle has bro ken dow n or you are
in an emergency s ituation, o r when
- yo ur vehicle is be ing towed by a tow
truck or if you are towing another vehicle
beh ind you.
Interior Lights
Front/rear interior lights
Fig . 38 Fro nt headl iner: int eri or lig h ting co ntro ls
Fi g. 39 Rear headli ner: rea r read ing lig hts
Press the corresponding switch:
~ -In ter ior lig hts on/off .
[ii-Courtesy light pos it io n. The inter ior lig ht­
ing auto mati ca lly comes o n when t he ve hicl e
i s un lo cke d, a door i s ope ned or the ig nitio n is
switched off. The interior lighting goes o ut a
few seconds after the doors a re closed, or
whe n the vehicle is locked or the ignition is
switched on. The lighting goes out automati ­
ca lly after a few minutes if a door is left open .
~ -Read ing lights * on/o ff ..,.

46 Clear vis ion
Sun visors
Fig. 43 Drive r's side : sun visor
The sun v isors for the driver and passenger
can be pulled out of the ir brackets in the cen­
ter of the vehicle and turned towards the
doors @.
The mirror light switches on when the cover over the vanity mirror @opens .
Wiper and washer
system
Switching the windshield wipers on
Fig. 44 Wind sh ie ld wipe r lever
Fi g. 4 5 O pera ting rear window w ipe r
" -0
='> a, a,
Move the windshield wiper lever to the cor re­
spond ing pos ition:
@ -Windsh ie ld wiper off
(D -Interval mode. To extend/shorten the
wipe r intervals, move the switch @to the
l eft/r ight . In vehicles with a ra in sensor* the
wipers turn on in the rain once the vehicle
speed exceeds approximately 2 mph (4 km/h).
The higher the sensit iv ity of the ra in sensor* is
set (switch @to the right), t he earlier the
windshield wipers react to moisture on the
windshield .
@ -Slow w iping
@ -Fast wip ing
@ -Sing le wipe . If you ho ld the lever in this
position, the wipe rs will switch from slow con­
tin uous wiping to fast cont inuous wiping after
a while.
® -C lean the w indshie ld. To elim ina te water
droplets, the windshield wiper performs one
afterwipe operation after severa l seconds
whi le driving. You can sw itch this function
off
by moving the lever to posit ion ® within 10
seconds of the afterwipe operat ion. The after­
wipe function is reactivated the next t ime the
ignition is sw itched on.
® -Rear wipe. The rear w indow is wiped ap­
proximately every 6 seconds.
(j) -Rear wash/wipe . The n umber of wiper cy­
cles depends on how long you hold the lever
in position
(J) .
A WARNING
-The rain sensor is only intended to assist
the dr iver. T he d river is st ill responsib le
for manually switching the wipers on ac­
cording to the visibility cond itio ns.
- The windsh ield may not be treated with
wate r-repell ing windsh ield coating
agen ts. Un favo rable cond it ions, such as
wetnes s, dark ness, low su n, c an result in
i n creased glare. Wipe r blade cha tter is
also possib le .
- Prope rly fun ct ion ing wi ndsh iel d wiper
b la d es are req uired for a clea r view and
safe driving
c:> page 47, Replacing
windshield wiper blades .

M N M N
0 :::i co
rl I.O
"' rl
"' rl
.. To sw itch the compass on or off, press and
hold the button @ until the compass dis­
play in the mirror
~ fig . 48 appears or disap ­
pears.
The digital compass only works when the igni ­
tion is on . The directions are indicated with
abbreviations:
N (north), NE (northeast), E
(east), SE (southeast), S (south), SW (south­
west),
W (west) , NW (northwest) .
(D Tips
To prevent inaccurate compass readings,
do not bring any remote controls, electri­
cal devices or meta llic objects nea r the
m irror .
Adjusting the magnetic zone
Applies to vehicles : wit h dig ital compass
The magnetic zone must be adju sted correctly
for the compass to read accurately .
~
[mJ ®
Fig . 4 9 No rt h A meri ca: magne tic de flect ion zo ne
bo undar ies
.. Press and ho ld the bu tton @ ~page 48,
fig . 48
until the number of the magnetic
zone appears in the rearview mir ror .
.. Press the button @ repeated ly to select the
correct magnetic zone. The selection mode
turns off after a few seconds. Clear vi
sion 49
Calibrating the compass
Applies to veh icles: w it h dig ita l compass
You must recalibrate the compass if it does
not display the correct direction .
.. Press and hold the button @ until a Cap­
pears in the rearview mirror .
.. Dr ive in a circle at about 6 mph (10 km/h)
until a d irection is displayed in the rearv iew
m irror .
.&_ WARNING
- To avo id end ange rin g yourse lf and other
drivers, ca libra te the comp ass in an a rea
where there is no traffic .
- Th e digi tal com pass is to be used as a di ­
rectional aid on ly . Even tho ugh you may
want to look at it while you are driving,
you must still pay attention to traffic, road and weather conditions as we ll as
other possible hazards.

Glove compartment
The glove compartment is illuminated,
cooled" and can be locked*.
Fig . 59 Glove compartment
Fi g. 60 Glove compartment: Switc h for the cooling
To open glove compartment
~ Pull the handle in the direction of the arrow
¢
fig. 59 and swing the cover down to open.
To close glove compartment
~ Push the glove compartment lid upward un­
t il the lock engages .
To switch the cooling on
~ Turn the rotary switch @ counter-clockwise
to switch the cooling on. The symbols on the
rotary switch must be displayed ¢
fig. 60 ac­
cordingly .
To switch the cooling off
~ Turn the rotary switch @ clockwise to
switch the cooling off.
The cooling box works only in the cooling
~ mode. If the climate contro l is in the heating
M N
0 ::i co
rl I.O
"' rl
"' rl
mode, we recommend switching the cooling
box off.
Seats and storage 55
A WARNING
To reduce the risk of personal injury in an
accident or sudden stop, always keep the
glove compartment closed while driving.
(upholder
Fig. 61 Center console: front cupho lde r
Fig. 62 Rear arm rest: rear cupho lder
Opening rear cupholders
~ To open the cupholder, press on the symbo l
i/@ ¢fig. 62.
~ To adjust the arm @, swing it in the direc­
tion of the arrow.
~ Place the beverage in the holder and release
the arm. The arm swings back by itself and
automatically secures the beverage.
Closing cupholders
~ To close the cupholder, press on the center
section between the two arms and push the
cupholder in the slot as far as it will go .
A WARNING
Spilled hot liqu id can cause an accident
and personal injury.
- Never carry any beverage conta iners with
hot liquids, such as hot coffee or hot tea,
II>-

64 Warm and cold
Operation
We recommend pressing the IAU TOI button and setting the temperature to 72 °F (22 °C) .
)-~~~
•I;. .. Q ~ - FRONT
Fig. 72 Dua l-zon e auto mat ic cl imate control: co ntrols
The functions can be switched on and off by
pressing the buttons . The LED in the corre­
sponding button lights up when the function is switched on .
IOFFI Switching the climate control
sy stem on /off
ThelOFFI b utton is used to switch the climate
control system on and off . When the climate
control system is switched off, the supp ly of
a ir from outside the car is cut off .
IA/Cl Switching cooling mode on /off
When the cooling mode is switched off, the
a ir is ne ither cooled nor dehumidif ied. The
windows may m ist up as a result. The cooling
mode is sw itched off automatically at low o ut­
side temperatures (below zero) .
1~ 1 Switching r ecirculat ion mod e on /off
In recirculation mode, the air from the interi­
or of the vehicle is filtered and recirculated .
This setting prevents fumes etc. from enter- 0
mil
--f-~
REAR ~~ -=-
ing the inte rior . We recommend switch ing on
the ai r recirculation mode when driving
t h ro ugh a tunne l or in traff ic queues ~.&. .
T he air reci rcul atio n mo de is switched off
whe n the !AUTO
I o r~ button is pressed .
T o sw itch on the automatic air recircu lation
mode, press the
1 ""' ·1 b utt on again . The top
LE D in the but ton will lig ht up. The air reci rc u­
lation mode wi ll be switched on automat ica lly
if you reverse the ve hicle while the engine is
cold. If coo ling mode (A/C) is sw itched off and
the weather is extremely c old, the automatic
air recircu lation will on ly operate for a limited
t ime .
IAU TOI
Switching automatic mode on /off
T he automatic mode maintains a constant
temperature inside the vehicle. Air tempera­
ture, output and d istribution are regulated
automat ica lly. ..,.

M N
M N
0 ::i co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
0 Adjusting the temperature
Separate temperatures can be selected for the
driver's and front passenger's side using the
left and right rotary controls . The tempera­
ture can be adjusted between +60
°F (+16 °C)
and +84 °F (+28 °C) . Outside this range, LO or
HI will appear on the air conditioner display .
In the two extreme settings the air condition­
er operates continuously with maximum cool­
ing or heating output, and the temperature is
not regulated automatically.
[:]1 (±] Adjusting the airflow
You can adjust the volume of air delivery man­
ually to suit your individual requirements.
Press the
IAUTOI button for automatic blower
regulat ion .
~/1 :J!/l~ I Adjusting the air distribution
You can direct the flow of air manually to se­
lected outlets. The buttons can be operated
e ither separately or in combination . Press the
IAUTOI button for automat ic air distribution.
J Adjusting the seat heating
When you press the button, the seat heating
is switched on at level 3 (the highest level) .
The LEDs indicate the temperature level. To
reduce the temperature, press the button
again . T o switch off the seat heating, press
the button repeatedly unti l all the LEDs have
gone out.
The seat heating automatically switches from level 3 to level 2 after 10 minutes .
I@ F RON T! Switching the defroster on/off
The windscreen and s ide windows are defrost­
ed or demisted as quickly as possible . The air
output is increased to maximum and most of
the air comes out of the outlets below the
windscreen . The air recirculation mode is de­
activated. The temperature should be set to
+ 72
°F (22 °() or higher.
The defroster is switched off when the
I AUTO I
button is pressed .
Warm and cold 65
!iii! REAR ! Switching the rear window
heating on/off
The rear window heating operates only when
the engine is running and switches off auto ­
matically after about 10 minutes.
Synchronisat ion
By pressing and ho lding the IAU TO j button,
you can set the temperature of the front pas­
senger's side to the temperature of the driv­
er's side. The synchronisation is deactivated as
soon as the temperature on the front pas­
senger's s ide is changed .
Air outlets
The thumbwhee ls can be used to open and
close the air outlets in the center and on ei­
ther side of the dashboard and rear center
console . The lever in the center of the outlets
can be used to adjust the direction of air flow.
Changing the temperature units
The temperature display can be switched be­
tween
° F and 0C. Press and hold the 1- ·1 but­
ton ¢
fig. 72 and turn the rotary control on
the driver's s ide to+ for 3 seconds.
A WARNING
- Do not use the recirculation for extended
periods of time. The windows could fog
up since no fresh air can enter the vehi­
cle. If the windows fog up, press the air
recir culation button again immediately
to switch off the air recirculation func­
tion or se lect defrost .
- Individ uals w ith reduced sensitivity to
pain or temperature could develop burns
when using the seat heating function. To
red uce the risk of injury, these individu­
als should not use seat heating .
(D Note
To avoid damage to the heating elements
in the seats, do not kneel on the seats or
place heavy loads on a small area of the
seat.