AUDI RS5 CABRIOLET 2013 Owners Manual

Wheel bolts
Wheel bolts must always be tightened to the
correct torque .
The design of wheel bolts is matched to the
factory installed r ims. If differen t rims are fit­
ted, the correct wheel bolts with the right l ength and correctly shaped bolt heads must
be used. This ensures that wheels are fitted
securely and that the brake system functions
correctly .
In certain circumstances, you may not use
wheel bo lts from a different vehicle -eve n if it
i s the same model
¢ page 266.
_&. WARNING
Improperly tig htened or maintained whee l
bolts can become loose ca using loss of
contro l, a co llision and serious persona l in­
jury.
- Always keep the wheel bolts and the threads in the wheel hubs clean so the
whee l bolts can turn easily and be prop­
erly t ightened.
- Never grease or oil the wheel bo lts and
the threads in the wheel hubs. They can become loose wh ile driving if greased or
o iled, even if tightened to the specif ied
torque .
- Only use wheel bolts that belong to the
rim being installed.
- Never use different whee ls bolts on your
vehicle .
-Always maintain the correct tighten ing
torque for the wheel bo lts to reduce the
risk of a wheel loss . If the tightening tor ­
que of the wheel bolts is too low, they
can loosen and come out when the vehi­
cl e is moving.
If the tightening torque is
too high, the whee l bolts and threads
can be damaged and the wheel can be­
come loose.
Q;) Note
The spec ified torque fo r the wheel bo lts is
90 ft lbs. (120 Nm) with a tolerance of
± 7,4 ft lbs.(± 10 Nm). Torque wheel bo lts
Tire s an d wheel s 239
diagonally. After changing a wheel, the
torque m ust be checked as soon as possi­
ble with a torque wrench -preferably by an
a uthori zed Audi dea ler or qualified work­
shop.
Low aspect ratio tires
Your Aud i is factory -equ ipped w ith low aspect
ratio tires . These tires have been tho roughly
tested and been se lected specifically fo r your
model for their superb perfo rmance, road fee l
and hand ling under a var iety o f driving cond i­
tions. Ask your authorized Audi dealer for
more details .
T he low aspect ratio of these t ires is ind icated
by a numeral of
55 or l ess in the tire's s ize
designation. The numera l rep resents the ra tio
of the tire's sidewa ll height in relation to its
tread width expressed in percentage . Conven­
tiona l tires have a he ight/w idth ratio of 60 or
more.
T he performance of low-a spe ct- ra tio tire s is
p ar tic ul ar ly se nsi tiv e to i mprop er i nfl ation
pre ssure. It is the refo re important that low
a spect ratio t ires are inflated to the specified
pr ess ure and that th e inflation pr essur e is
r e gula rly ch ecked and maintain ed. Tir e pre s­
s ure s should b e check ed at l east once a
m onth and alwa ys befo re a long trip
¢ page 228, Checking tire pressure.
What you c an do to avo id tire and rim
damage
Low aspect ratio tires can be damaged mo re
easily by impact w ith potholes, curbs, g ull ies
o r ridges on the road, pa rticularly if the tire is
u nderinflated.
In orde r to minimize the occurrence of impact
damage to the tires of your vehicle, we recom ­
mend that you observe the following p reca u­
tions:
- Always ma inta in recommended inflation
pressu res. Check your tire pressure eve ry
2,000 miles (3,000 km) and add air if neces-
sary . .., •
•

24 0 T ire s and wheel s
- Drive carefu lly on roads with potholes, deep
gullies or ridges. The impact from driving
through or over such obstacles can damage
your tires. Impact with a curb may also
cause damage to your tires.
- After any impact, immediately inspect your tires or have them inspected by the neares t
authorized Aud i dealer. Replace a damaged
t ire as soon as possible .
- Inspect your t ires every 2 ,000 miles (3,000
km) for damage and wear . Damage is not al­
ways easy to see . Damage can lead to loss of
air and underinflation, wh ich could eventu­
ally cause t ire failu re. If you be lieve that a
t ire may have been damaged, replace the
t ire as soon as poss ible.
- T hese tires may wea r more quick ly than oth­
ers.
- Please also remember that, whi le these t ires
deliver respons ive handling, they may ride
less comfortably and make mo re no ise than
othe r choices.
Reduced perf ormance in winter /cold
sea son condit ion s
All ti res are des igned for certa in pu rposes.
The low aspect ratio, u ltra high performance
tires originally installed on your vehicle are in­
tended for max imum dry and wet road per­
formance and handling . They are not suitable
for cold, snowy or icy weather condit ions. If
you dr ive under those circumstances, you
should equip your vehicle with all-season or
winter tires, which offer better traction under
those cond it ions . We suggest you use the rec­
ommended snow or all-season tires specified
for your vehicle, or their equ ivalent .
Refe r to
<=> page 23 7 for more deta iled infor­
ma tion regarding w inter tires.
Tire pressure
monitoring system
(l) General notes
App lies to vehicles: with tire pressure monitoring system
Each tire shou ld be checked monthly when
cold and inflated to the inflat ion p ressu re rec- ommended by the vehicle manufacturer on
the ve hicle p lacard or tire inflation press ure
label. (If yo ur vehicle has tires of a d ifferent
s iz e than the si ze indicated on the veh icle
placard or tire inflation pressure label, you
should determine the proper tire inflation pressure for those tires) .
As an added safety feature, your veh icle has
been equipped with a tire pressure monitoring
system (TPMS) that illum inates a low tire
pressure telltale when one or more of you r
tires is significantly under-inflated . Acco rding­
ly, when the low tire pressure telltale illumi­
nates, yo u shou ld stop and check you r tires as
soon as possib le, and inflate them to the
proper pressure . Driving on a signi ficantly un ­
der-inflated tire causes the tire to overheat
and can lead to tire fa ilure. Under-inflation al­
so reduces fuel effic iency and tire tread life,
and may affect the vehicle's handling and
stopp ing ability.
P lease note that the TPMS is not a substitute
for proper tire ma intenance, and it is the driv­
er's responsibility to maintain correct tire
pressure, even if under-inflation has not
r eached the level to tr igger illuminat ion of the
T PMS low tire pressu re tellta le.
Your vehicle has also been equipped with a
TPMS ma lfunction indicator to ind icate when
the system is not operating prope rly. The
T PMS ma lfunction ind icator is comb ined w ith
the low t ire pressure telltale . Whe n the sys­
tem detects a malfunc tion , the telltale will
flash fo r approxima tely one min ute and then
remain continuously i lluminated. This se­
quence wi ll continue upon subsequent vehicle
start-ups as long as the malfunct ion exists .
When the malfunction indicato r is illum inat­
ed , the system may not be ab le to detect or
signal low tire pressure as intended . TPMS
malfunctions may occur for a var iety of rea ­
sons, including the installation of replace­
ment or alternate tires or wheels on the vehi­
cle that prevent the TPMS from functioning
properly . Always check the TPMS malfunction
te lltale after rep lacing one or more tires o r
whee ls on your vehicle to ens ure that the

replacement or alternate tires and wheels a l­
l ow the TPMS to continue to function proper­
l y.
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
F ig. 190 Display: underinflatio n warn ing
Using the ABS sensors , the t ire pressure mon i­
toring system compa res the t ire tread circum­
fe rence and v ibration characteristics of the in­
d iv idual tires. If the pressure decreases in one
or mo re tires, th is is indicated in the instru ­
ment cluster with a
ti] warn ing symbol and a
message ¢
fig. 190. The driver message in the
disp lay goes out after S seconds. The driver
message can be d isplayed again by pressing
the
! S ET ! button. If only one tire is affected,
the display will indicate its pos ition .
T he t ire pressure monitoring system must be
reset via radio or MMI* each t ime the pres­
sures are adjusted (e.g . when sw itching be­
tween partia l and full load pressure) or after
changing o r replacing a t ire on your vehicle
¢
page 242. The TPMS indicator only moni­
tors the tire p ressure that you have prev iously
stored . Yo u ca n find the recommended tire
p ress ures for you r vehi cle on the labe l on dr iv­
er's side B -pi llar ¢
page 226 .
T ire tread c ircumfe rence and vibration c harac­
ter ist ics can ch ange and ca use a ti re pressure
warn ing if:
- the tire pressure in one o r more t ires is too
low,
Tire s an d wheel s 241
- the t ire has struc tural damage,
- t he t ire press ure w as c hanged, wheels ro ta t-
ed or rep laced but the TPMS was not reset
¢ page 242.
Warning symbols
ti] Loss of pressure in at least one tire¢& .
Check the t ire o r tires and rep lace or repa ir if
necessary. The
ti] indi ca to r li ght in the inst ru­
ment cluster a lso illuminates
¢ page 13.
Check/cor rect the press ures of all fo ur tires
and reset TPMS via radio or MMI*.
11il~1 (T ir e Pressure Monitoring System) Tire
pre ssure: Sy stem m alfunction!.
IfllilB appears after switching the ignition
o n or while d rivi ng and the
ti] ind icator l ight
i n the instr ument cluster blinks for app roxi ­
mately one minute and then stays on, there is
a system malfunct ion .
Attempt to sto re the co rrect tire pressu re
¢
page 242. If the ind ic a tor lig ht does not
turn off or i f it turns on sho rtly the rea fter, im ­
med iate ly dr iv e your vehicle to an authorized
A udi dealer or authorized repair faci lity to
have the malfunct ion corrected.
A WARNING
- If the tire pressure ind icator appears in
the instrument cluster display, one or more of your t ires is sign ificant ly unde r­
inflated . Reduce you r speed immediately
a nd avoid any hard steer ing or b rak ing
maneuvers. Stop as soon as possib le and
check the tires and their pressu res . In­
f late the tire pressure to the prope r pres ­
sure as indicated o n the vehicle's tire
pressure labe l
¢page 226. D riving on a
sign ificantly under-inflated tire causes
the t ire to overheat and can lead to tire
fa ilure. Under-inflation also is likely to
impair the vehicle's ha ndling and stop­
ping ab ility .
- The drive r is responsib le for maintaini ng
the co rrect tire pressures . You must
check the tire pressures regu larly. .,..
•
•

242 Tires and wheels
-Under certain conditions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor indi­
cator may be delayed.
- Ask your authorized Audi dealer if run­
flat tires may be used on your vehicle.
Your vehicle registration becomes invalid
if you use these tires when not permit­
ted. Damage to your vehicle or accidents
could also result.
@ Tips
-The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction.
- Using snow chains may result in a system malfunction .
- The tire pressure monitoring system on
your Audi was developed using tires with the
"ROl" identification on the tire side­
wall ~
page 233. We recommend using
these tires.
Reset tire pressure monitoring system
Applies to vehicles: with tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or chang ed, the
TPMS must be reset via
radio or
MM!* .
.. Before resetting the TPMS, the current pres­
sures of all four tires must correspond to
the specified values. Adjust the tire pressure and reset the pressure in the tire pressure
monitoring system according to the load
you are carrying
~ page 226 .
.. Turn on the ignition .
.. Select : the
ICAR I function button > Tire pres­
sure monitoring > Store now .
Or
.. Select : the ICA RI function button > Car sys­
tems*
control button > Servicing & checks>
Tire pressure monitoring > Store tire pres­
sures.
@ Tips
Do not store the ti re pressure if there a re
snow chains on the tire.

What do I do now?
Vehicle tool kit
The tools ore stored underneath the floor
panel in the luggage comportment.
F ig . 191 Lug gage compartment: tool kit
When you need access to the veh icle tool kit
or jack*, you will need to take o ut the cover.
The vehicle tool kit includes:
- Tire repair kit (Tire Mobility System)
- Plastic cl ip for removing wheel bo lt caps*
- Al ignment p in for ch anging the whee l
- Screwdriver with reversible blade
- Tool for chang ing light bulbs
- Reversible bit (reversible Torx bit for chang-
ing light bulbs)
- Rod for jack
- Jack *
- Lug wrench
- T owing eye
Some of the vehicle items listed above a re
prov ided o n certain models on ly o r are option­
a l extras.
Before returning the jack * to its place, retract
the jack arm fully.
..&, WARNING
-
- Never use the screw d river hex head to
t igh ten whee l bol ts, si nce the bolts can­
not at tain the necessary tightening tor­
que if you use the hex head, poten tially
causing an accident.
- T he factory -supp lied jac k is intended on­
ly for your vehicle model. Under no cir­
c u mstances should it be used to lift
What do I d o now ? 243
heavy veh icles or other loads; yo u risk in­
juring yourself.
- Never start the engi ne when the vehicle
is raised, which could cause an acc ident.
- Support the vehicle secure ly wit h appro­
priate stands if wor k is to be performed
underneath the vehicle; otherwise, there
is a pote ntia l risk for injury.
Tire repair
General and safety pointers
Tire repair is intended only for temporary,
short-term use.
F ig . 1 9 2 Tire damage fo r wh ich the Tire Mob ility Sys­
tem is not suited
Your vehicle is equipped with a tire repa ir k it,
the
Tir e Mobility Sy stem (TMS ).
In the event of a tire failure, the TM S is in the
luggage compartment under the floor. It con­
s ists of the tire sealant and an electric air
pump .
Using
TM S, tire damage caused by foreign
bodies up to about
0.1 6 inch (4 mm ) in diam­
eter can be sea led reliably.
The foreign object must stay in the tire .
The tire sealant must not be used:
-for cu ts or punctures in t he tire w hich a re
large r th an 0. 16 inc h (4 mm) <=>fig. 192
©
-for damage to the rim @
- if you have been driving with very low t ire
pressu res or tires with no air@
Using the
TMS is descr ibed in the section
<=> page 244.

244 What do I do n ow ?
TMS can be used at temperatures down to
-4°F(-20°C).
.&_ WARNING
Take the following precautions after re­
pairing the tire:
- Do not d rive faster than 50 mph (80 km/
h)!
- Avoid full-throttle acce leration, heavy
braking and fast cornering.
- The veh icle's road behav ior can be affect­
ed.
- Tires sealed with
T M S are intended only
for
temporar y, short-te rm use . Dam­
aged tires must be replaced . Drive care­
fully to the next professional repair fa ­
cility.
- After using the tire sea lant the tire pres­
sure monitoring system may no longer
work properly. Drive carefully to the next
professional repair fac ility.
- TM S must NOT be used,
- for cuts or punctures in the tire which
are larger than 0.16 inch (4 mm)
- for damage to the r im
- if you have been dr iv ing with very low
tire pressures or t ires with no air
- Seek professional assistance if it is not
poss ible to repair the tire with the tire
sealant.
- The tire sealant must not come into con­
tact with sk in, eyes or clothing.
- If you get any tire sealant in your eyes or
com e into contact with i t, rinse the af­
fected area tho roughly w ith clean wate r.
Find a physician immediate ly!
- Change any clothing contaminated w ith
t ire sealant immed iate ly.
- Do not inhale t he vapo r!
- If you have swallowed t ire sealant , rinse
yo ur mouth thorough ly r ight away and
dr ink p lenty of water.
- Do not induce vomiting! Find a physi ­
cian immediate ly!
- If you have a llergic reactions, f ind a
physician immediate ly.
- Keep the t ire sealant away from chi ldren.
(D Note
Do not use commercially avai lab le tire
sea lants. The electr ica l components of the
tire pressure monitoring system will no
l onger work properly.
«!) For the sake of the environment
Used sealant bottles ca n be dropped off at
a recycling facility .
(D Tips
-If sea la nt has run out, allow it to dry .
Then you can peel it off .
- Have the t ire sea lant rep laced eve ry 4
years at a dealersh ip.
Making a tire repair
Fig . 19 3 Mak ing a t ire repa ir
Preliminary steps
"' If you have a flat tire, park the vehicle as far
as poss ible from moving traffic.
"' App ly the par king b rake firmly.
"' Move the se lector lever to the P position
"' Check whether a repair using the Tire Mobili­
ty System is possible
c:::> page 243.
"'Have all passengers leave the vehicle and
stay away from the danger zone
c:::> _&..
"'Take the sealant bottle and the electric air
pump from the luggage compartment under
the floo r<=;>
page 243.
"' Remove the "max . SO mp h" (80 km/h) s tick ­
er from the sea lant bottle and affix i t to the
instr ument clus ter in the drive r's view .
Filling a tire
"' Shake the bott le thoroughly before filling. Ill>

~ Screw the accompanying filling hose com­
pletely onto the bottle. This breaks through
the foi l seal automat ically at the connec­
t ion.
~ Remove the valve cap from the tire valve and
unsc rew the valve insert us ing the accompa ­
nying valve insert tool¢
fig. 193 .
~ Lay the valve insert on a clean surface .
~ Remove the sealing plug from the filling
hose and connect the hose to the tire v alve.
~ Hold the bottle with the bottom fac ing up ­
ward and emp ty the entire contents into the
tire .
~ Then pu ll out the hose and screw the valve
insert tightly back into the tire valve.
Inflating a tir e
~ Screw the filling hose for the electric a ir
pump onto the tire valve and insert the con­
nector into the cigarette lighter .
~ Inflate the t ire between 2.0 and 2.5 bar and
read the pressure from the gauge.
~ If this tire pressure is not reached, drive
your vehicle approximate ly 10 meters for ­
ward or backwa rd so that the sealant can be
redistributed i nside the tire . If at th is time
the req uired air p ressu re still cannot be
reached, the t ire is too badly damaged and
cannot be repa ired with the tire sea lant.
Final check
~ After dr iving for about 10 minutes, stop and
chec k the t ire p ressure.
~ If tire pressure is less than 1.3 bar, the tire
is too seve rely d amaged. Do not contin ue to
dr ive . Seek pro fessional assistance.
& WARNING
- Turn on the emergency flashers and set
up the emergency triangle if you have
flat tire while in mov ing traffic. This is
for your protection and the for the safety
of other drivers.
- Have all passengers leave the vehicle and
stay away from the danger zone (for ex­
amp le, beh ind a guard rail) .
What do I do now? 245
-Read and follow the manufacturer's safe­
ty precautions on the compressor and in
the instructions on the bottle of sealant!
- If a tire pressure of 2.0 bar cannot
reached after inf lating for six minutes,
then the tire is too severely damaged. Do not continue driving!
- Obta in qua lified help if it is not possible
to pe rform the repair wit h the t ire seal­
a nt.
- If the tire pressure is less than 1.3 bar
after 10 m inutes of driv ing, then the the
tire is too seve rely damaged. Do not con­
tinue dr iving . Seek profess iona l assis­
tance .
(D Note
Particular care is necessary if you are mak­
i ng a tire repa ir on a steep incl ine .
(D Tips
-Do not operate the electric air pump for
more than 6 minutes without stopping,
otherwise it can over heat. When the a ir
pump has coo led down, you can continue
t o use it.
- If sea lant has spilled out, let it dry and
then you can remove it by peeling it away
like a foil.
- Remember to obtain a new bott le of
sealant from yo ur autho rized Aud i dea le r
afte r repairing a tire. After this, the func­
tionality of the tire repa ir set is restored.
- Obey all laws.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger 's safety when chang­
ing a wheel.
~ After you experience a tire failure, pull the
car we ll away from moving traffic and try to
reach
le vel ground before you stop ¢ ,&..
~ All passengers should lea ve the car and
move to a safe location (for instance, behind
the guardrail) ¢
,&.. ..,.
•
•

24 6 What do I do no w?
• Engage the par king br ake to prevent your
vehicle from rolling unintentionally
c> _&..
• Move the sel ector le ver to the P po sition.
• Take the jack c> page 243 out of the luggage
compartment.
A WARNING
You or your passengers could be injured
wh ile cha nging a wheel if you do not fol­
low these safety precautions:
- If you have a flat t i re, move a safe dis­
tance off the road . Turn off the engine,
tu rn the emergen cy flashers on and use
other wa rning dev ices to alert other mo­
torists.
- Make su re that passengers wait i n a safe
pla ce away from the vehicle and well
away from the road and traff ic.
- T o help prevent the veh icle from mov ing
sudden ly and possibly slipping off the
jack, a lways fully set the parking brake
and block the whee l diagona lly opposite
the whee l being changed with the fo ld­
ing chocks or other objects. When one
front whee l is lifted off the ground, plac­
ing the Automat ic Transmiss ion in "P"
(Pa rk) w ill
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the ground is level and firm . If necessary,
use a sturdy board unde r the jack.
- Always store the vehicle tool kit, the
jack* and the replaced tire in the luggage
compartment
c> page 124.
(D Note
If you are chang ing the wheel on a steep
incline, use a rock or similar object to
b loc k the opposite wheel to prevent the
veh icle from mov ing.
Obey all laws.
-
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order .
l. Remove the wheel bolt caps* . For more
details see also
c> page 247, Wheels with
wheel bolt caps.
2. Loosen the wh eel bolts c>page 247.
3. Locate the p roper mounting point fo r the
ja ck a nd align the jack below that point
c>page248 .
4. Lift the car with the jack c> page 248 .
5. Remove the wheel with the flat tire and
then insta ll the other wheel
c> page 249.
6. Tighten all wheel bolts lightly.
7.
Lower the vehicle with the jack .
8. Use the wheel bolt w rench and
firmly
t ighten all wheel bolts in a crisscross pat­
te rn
c> page 247.
9. Replace the wheel bolt cap s*.
A WARNING
Always read and fo llow all WARN INGS and
informat ion c> .&. in Raising the vehicle on
page 248
and c> page 250 .
After changing a wheel
A wheel change is not comple te without the
doing the following .
• Always store the vehicle tool kit, the jack*,
and the rep laced tire in the luggage com ­
partment
c> page 124.
• As soon as possib le, have the t ightening
torque s
on all whee l bolts checked with a
torque wrench. The correct tightening tor­
que is 90 ft lbs. (120 Nm).
• Have the flat tire
re plac ed as soon as possi­
ble.
(D Tips
- If you not ice that the wheel bolts are
corroded and difficult to turn while
chang ing a tire, they should be replaced
before you check the tightening torque .

-Drive at reduced speed until you have the
tightening torques checked.
Wheels with wheel bolt caps
Applies to vehicles: with wheel bolts wit h caps
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed .
Fig. 194 C hangin g a whee l: removing the wheel bo lt
caps
R em oving
.,. Push the
pla stic clip provided w it h the vehi­
cle tool kit over the wheel bolt cap until it
engages.
.,. Pull on the
pl as tic clip to remove the cap
¢fig . 194 .
Refitting
.,. Place the caps ove r the wheel bo lts and
push them back on .
The caps are to protect and keep the wheel bolts clean.
What do I d o now ? 24 7
Loosening and tightening the wheel
, bolts
The wheel bolts must be loosened before rais­
ing the vehicle.
F ig . 1 95 Changing a whee l: loosen ing t he wheel bolts
Loos en ing
.,. Insta ll the
w heel bolt wre nch over the
wheel bo lt and push it down as far as it will
go .
.,. Take tight hold of the
end of the wrench
handle and turn the wheel bo lts
counter­
clockwi se
about one single turn in the direc­
tion of arrow ¢
fig. 195 .
Tightening
.,. Insta ll the
wheel bolt w ren ch over the
wheel bo lt and push it down as far as it will
go .
.,. Take tight hold of the
end of the wrench
handle and turn each wheel bolt
clockw ise
until it is seated .
.&_ WARNING
- Do not use fo rce or h urry whe n chang ing
a wheel - you can ca use the vehicle to slip
off the jack and cause serious personal
inj uries.
- Do not loosen the wheel bo lts more than
one turn
befo re you raise the vehicle with
the jack . - Yo u risk an injury .
{D Tips
- Never use t he hexagona l so cket in the
hand le of the screwdr iver to loosen or
tighten t he wheel bolts .
- If a wheel bo lt is very tigh t, you may find
it eas ier to loosen by carefully pushing ..,.

248 What do I do now?
down on the end of the wheel bolt
wrench with
one foot only . As you do so,
hold on to the car to keep your balance
and take care not to slip.
Raising the vehicle
The vehicle must be li~ed with the jack first
before the wheel can be removed.
Fig. 196 Sill panels: mark ings
Fig. 197 Sill: posit ion ing t he veh icle jack
The location of the jack point is indicated by
an indentat io n on the underside of the vehicle
~ fig. 196 .
• Activate the parking brake to prevent the
vehicle from rolling unintentionally.
• Move the selector lever to posit ion P.
• Find the
marking on the si ll that is nearest
the wheel that w ill be changed
<=>fig. 196 .
Behind the marking, there is a lifting point
on the sill for the vehicle jack.
• Turn the
vehicle jack located under the lift­
ing point on the si ll to raise the jack until
the jaw
r::> fig. 19 7 @ covers the notch on
the vehicle<=> &<=>CD .
• Align the vehicle jack so the jaw@ covers
the notch and the base p late @ is flat on
the floor . The base plate@ must be
vertical
under the lifting point @. •
Install the rod on the vehicle jack : Insert the
rod into the opening on the handwheel. Turn
the rod left or r ight to secure it.
• Continue raising the jack with the rod unt il
the wheel lifts off the ground slightly.
Position the vehicle jack
only under the desig­
nated lifting points on the si ll
<=>fig. 196.
There is exactly one location for each wheel.
The jack must not be positioned at any other
location <=> .&. <=>CD .
Soft ground under the jack can cause the ve­
hicle to slip off the jack. Always place the jack
on firm ground. Use a flat, stable support if
necessary. Use a non -slip surface such as a
rubber mat on a
slippery surface such as tile .
.&, WARNING
-You or your passengers could be inju red
while changing a wheel if you do not fo l­
low these safety precautions:
- Position the vehicle jack only at the designated lifting points and align the
jack. Otherwise, the vehicle jack could
slip and cause an injury if it does not
have sufficient hold on the vehicle.
-A soft or unstable surface under the jack may cause the vehicle to slip off
the jack. Always provide a firm base for
the jack on the ground. If ne cessa ry,
us e a sturdy board under the jack.
- On hard, slippery su rface (such as tiles)
u se a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the veh icle and
well away from t he road and traffic.
- Make sure jack position is correct, ad­
ju st as necessary and then continue to
raise the jack. .,_