warning AUDI TT 2013 Owner´s Manual

72 On the road
you leave your veh icle . This makes a vehicle
theft even more difficult ¢ .&. .
Ignition ke y saf ety lock
After swi tching off the ignition, the ig nit ion
key can on ly be removed from the ign it ion
lock when the se lector lever is in the "P"
(Park) position . After you have removed the
key, the selector lever is locked and cannot be
moved.
Ignition on @
If it is diffic ult to turn the key after you have
inserted it into the ignition lock, turn the
steering wheel back and forth. This will take
the load
off the steering lock mechanism and
you will be able to turn the key freely and
start the engine.
Starting the engine @
In this position the engine starts . While the
engine is starting, the power supply to the headlights and other e lectrica l consumers is
temporari ly interrupted to conserve battery
power. After the engine has started, release
the key and it will return to posit ion
(D .
Before the starter can be operated again the
key must be turned back to position @. The
non -repeat loc k prevents you from damaging
the starter when the engine is runn ing .
A WARNING
-Never remove the key from the ign ition
lock whi le the vehicle is moving. The
steeri ng wheel will lock causing loss of
c ontrol.
- If you have to leave your vehicle -even
for just a m inute -always remove t he ig­
nition key and take it with you. This is es­
pecially important if you a re going to
leave ch ildren behind in the vehicle. The
children co uld start the engine or use
other vehicle controls. Unsupervised use
of vehicle controls (for examp le, power
windows) can cause serious personal in­
jur ies .
(!) Tips
If the vehicle battery has been disconnect­
ed and then reconnected, then you must
l eave the key in position
(D for about 5
seconds before you can start the engine.
Starting and stopping
the engine
Starting the engine
The engine can only be started with an origi­
nal Audi key.
.,. Set the park ing brake.
.,. Move the se lector lever to the neutral posi ­
tion (automatic transmission): selector lever
in
P or N) ¢ .&_ .
.,. On vehicles with manua l transmission, fully
depress the clutch pedal.
.,. Turn the ignition key to pos it ion @
¢ page 71, fig . 71 -do not depress the gas
pedal when starting the engine!
.,. Let go of the key as soon as the engine
starts.
A cold engine may at first be loud after it has
been sta rted. This is due to the hydrau lic
valves bu ild ing up the oil pressure. This nor­
mal and no need for co nce rn .
If the engine does not start immediately, stop
trying after 10 seconds and then try to restart
the engine abou t 30 seconds late r.
A WARNING
Neve r star t or let the eng ine run in a con­
f ined or enclosed area . Exhaust fumes
from the engine contain carbon monoxide,
a colorless and odor less gas . Ca rbon mon ­
oxide can be fatal if inhaled.
- Never leave the engine id ling unattend­
ed. An unattended veh icle w ith a runn ing
engine poses a danger of personal injury
or theft.

CD Note
-Avoid high engine speeds, fast accelera­
tion or heavy engine loads whi le the en­
gine is still cold. This could damage the
engine.
- The engine cannot be started by pushing or towing the veh icle.
@) For the sake of the environment
To avoid unnecessary engine wear and to
reduce exhaust emissions, do not let your
veh icle stand and warm up. Be ready to
drive off immediately after starting your
veh icle. Maintain moderate speed until the
eng ine is completely warm . Remember,
the engine performs best at operating
temperature .
Stopping the engine
~ Turn the ign ition key to position @
~page 71, fig. 71.
_& WARNING
-Never turn off the engine before the ve­
hicle has come to a complete stop. The
full function of the brake booster and the
power steering is not guaranteed . You
must use more force to turn or brake if
necessary. Because you cannot steer and
brake as you usually would, this could
lead to crashes and serious injur ies.
- The radiator fan can continue to run for
up to 10 minutes even after you have
turned
off the engine and removed the
ignition key . The radiator fan can also
turn on again if the engine coolant heats
up because of intense sunlight or heat
build-up in the engine compartment.
CD Note
Do not stop the engine immed iate ly after
hard or extended driving. Keep the engine
running for approximately two minutes to
prevent excessive heat build-up.
On the road 73
Parking brake
Parking brake
When the parking brake is set, it prevents the
vehicle from rolling away unintentionally .
Fig. 72 Center console: Parki ng b rake set
Setting the parking brake
~ Pull the park ing brake lever all the way up.
Releasing the parking brake
~ Pull the parking brake lever up slightly and
press the release button at the same time
~ fig. 72 -arrow-.
~ Keep the release button pressed and lower
the parking brake~&_ .
If you should drive
off with the parking brake
still set, a warning tone will sound and the
follow ing will appear in the instrument clus­
ter to rem ind you to release the parking
brake:
Handbrake is applied
The parking brake warning comes on only af­
ter you have driven for longer than 3 seconds
and faster than 5 mph (5 km/h) .
The parking brake warning light_
(USA)/ . (CON) illuminates when the park­
ing brake is set and you switch on the ignition .
A WARNING
Always re lease the park ing brake com -
pletely. A partially engaged brake will
overheat the rear brakes, reduce their ef­
fectiveness and cause excessive wear. This
could lead to brake failure and an accident. .,.

74 On the road
Only afte r the vehic le has come to com­
p lete stop, should you f irm ly set the park­
ing brake and either move the gearshift
lever into 1st. gear (manual transm iss ion)
or move the selector lever into "P" (Auto­
mat ic transm ission).
Parking
Parking
.,. Stop the veh icle using the brake pedal.
.,. Set the parking brake firmly .
.,. Switc h off the eng ine.
.,. Move t he selecto r lever in to the P position
(autom atic tr an smi ssio n) or move the gear­
shift lever into 1st . gear
(manual t ransmi s­
sion ).
.,. Remove the ign ition key from the ignit ion
lock.
In addition on incline s and grad es
.,. Turn the steering whee l so that your vehicle
wi ll ro ll against the curb in case it should
start to move.
A WARNING
This is how you can reduce the risk of in­
jury when leaving your veh icle.
- Never park the vehicle where it can come in contact with dry grass, sp illed fuel or
any other flammable mater ials .
- Never allow anyone - especially small
children -to remain in the vehicle when
it is locked. Locked doors make it more
difficult for rescuers to access the pas­
senger compartment in the event of an
emergency. Danger to life!
- Never leave children unsupervised in the
vehicle. Children could re lease the park­
ing brake o r move the gea rshift lever out
of gear. The vehicle could start to roll
away and cause an accident .
- No matter what the season is, the tem­
perature in a parked vehicle can reach
dangerous levels .
Starting on hills
Applies to vehicles: wi th hill hold assist
Hill ho ld assist makes it easier to start on
hills.
T he system is activated when the bra ke peda l
is depressed
for a few sec ond s.
After releasing the brake pedal, the brake
power is held for a
brief moment to p reven t
the vehi cle from rolling back when s tarti ng. At
th is time, you can easi ly beg in to move your
vehicle .
A WARNING
- If you did not begin moving immediate ly
after releasing the brake pedal, under
certain circumstances, the vehicle would
begin to roll backward. Depress the
brake peda l immediately or engage the
hand brake.
- Should the engine stall, depress the
brake peda l immediately or engage the
hand brake .
- In order to prevent the vehicle from roll­ ing back unintentionally when starting in
stop-and-go traffic, keep the brake pedal
depressed for a few seconds before driv­
i n g off.
@ Tips
You can find o ut if yo ur vehicle is equ ipped
with "Hill hold ass ist" at an authorized
Audi dealersh ip.
Speed warning system
Overview
The speed warning system helps you to keep
your driving speed below a set speed limit.
The speed warning system warns the driver if
he exceeds a previous ly stored maximum
speed. A warning tone will so und as soon as
the vehicle speed exceeds the set speed by
about 3 mph (3 km/h). At the same time, a
warning symbol appears in the display. .,,.

The speed warning system has two warning
thresholds
that function independently of
each other and that have somewhat different
purposes:
Speed warning 1
You can use speed warn ing 1 to set the maxi­
mum speed while you are driving. This setting
will remain in effect until you turn
off the igni ­
tion, assuming that you have not changed or
reset the setting.
The speed warning symbo l
(mj (USA models)/
(SJ (Canada models) in the warning 1 display
appears when you exceed the maximum
speed.
It goes out when the speed falls below
the stored max imum speed.
The speed warning symbo l wi ll also go out if
the speed exceeds the stored maximum speed
by more than about 2S mph (40 km/h) for at
least 10 seconds. The stored maximum speed
is deleted.
Setting speed warning l <=:> page
75.
Speed warning 2
Stor ing warn ing 2 is recommended if you al­
ways want to be reminded of a certa in speed,
for example when you are traveling in a coun­
try that has a general maximum speed limit,
or if you do not want to exceed a spec ified
speed for winter tires.
The speed warning 2 symbol,
(zj <USA mod­
els)/
(•j (Canada models) appears in the dis­
p lay when you exceed the stored speed lim it.
Unlike warning 1, it will not go out until the
vehicle speed drops below the stored speed limit .
Sett ing speed warning 2 <=:>page 76.
@ Tips
Even though your vehicle is equipped with
a speed wa rning system, you should sti ll
watch the speedometer to make sure you
are not driving faster than the speed lim it.
On the road 75
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the button.
Fig. 73 Sect ion of instrument clus ter: Set/C heck but ·
ton
Storing the maximum speed
.,. Drive at the des ired maximum speed .
.,. Press the knob buttonr=:>fig .
73 unti l the
speed warning symbol
[iJ (USA models)/ ~
(Canada models) appears.
Resetting the maximum speed
.,. Drive the vehicle at a speed of at least
3 mph (5 km/h)
.,. Press the knob for more than 2 seconds.
The speed warning symbol
(G:l (USA models)/
i•j rcanada models) will appear briefly in the
display when you release the button to indi­
cate that the maximum speed has been stored
successfully .
The maximum speed remains stored until it is
changed by pressing the button aga in brief ly
or until it is deleted by a lengthy push on the
button.

76 On the road
Speed warning 2: setting a speed limit
Switches in the wiper arm are used to operate
warning threshold
2 .
'----I ®
Fig. 74 Wiper lever: Tr ip computer con trols
To store maximum speed
> Turn off the ignit ion.
> Briefly press the button in the instrument
cl uster ¢
page 75, fig. 73. The odometer
and the digital clock are now illuminated .
> Press the button for at least 2 seconds. The
currently stored maximum speed appears in
the display
or the crossed out symbol for
warning threshold 2, if no max imum speed
was set previously.
> Press the function selector sw itch in the
wipe r lever @¢
fig. 74 up or down to
change the set value. Values run up or dow n
i n steps of 6.2 mph (10 km/h).
To delete maximum speed
> Turn off the ignit ion .
> Briefly press the button in the instrument
cluster ¢
page 75, fig . 73. T he odometer
and the digital clock are now illumi nated.
> Press the button for at least 2 seconds . Th e
cu rrently stored maxim um speed appears in
the display.
> Press the reset button in the wiper lever ®
¢fig . 74 until the crossed out speed warn­
ing symbol for warning threshold 2 appears
i n the display.
A few seconds after the adjustment is com­
pleted, the illumination for the odometer and
the dig ital clock will go out.
(D Tips
This warning threshold can a lso be con­
trolled thro ugh the tr ip computer
¢ page 25, Navigating the menu.
Cruise control
Switching the system on
The cruise control system makes it possible to
drive at a constant speed starting at 20 mph (30 km/h) .
®-
Fig. 75 Contro l leve r with set b utton
Fig. 76 D isplay : Se lecte d speed
> Pull the lever to position (D ¢ fig. 75 to
switch the system on.
> Dr ive at the speed you w is h to set.
> Press button @ to set that speed.
.., ....
i
The display ¢ fig. 76 will show the set speed .
The display may vary depending on the type of
display in your vehicle. The indicator light
M;ll)~14 (US model)/ . (Canadian model) will
also light up in the instrument cluster .
A WARNING
- Always pay attention to traffic even when
the cruise control is switched on. You are
always responsib le for your speed and

the distance between your vehicle and
other vehicles.
- For safety reasons, the cruise control
should not be used in the city, in stop­
and-go traff ic, on twisting roads and
when road conditions are poor (such as
ice, fog, grave l, heavy rain and hydro­
planing) -risk of acc ident .
- Turn off the cruise control temporari ly
when entering turn lanes, highway exit
lanes or in construction zones .
- Please note that inadvertent ly "rest ing"
yo ur foot on the accelerator peda l causes
the cruise control not to brake. This is
because t he cr uise con trol is overridden
by the driver's acce lerat ion.
(D Tips
- Vehicles with manual t ransmission: You
can attain the set speed only if the cur­
r ently e ngaged gear a llows i t and the en­
gine i s not stressed. Shift ing to a h igher
or lower gear p romp tly will allow t he en­
gine to run smoothly.
- The cruise cont ro l cannot main tain a
constant speed when driving downhill.
The vehicle will accelerate unde r its own
weig ht. Downsh ift to a lower gear or use
the brakes to slow down.
Changing speed
"' Press lever in the 0 or 0 direction
i=> page 76, fig . 75 to increase or decrease
you r speed .
"' Re lease the lever to save that speed.
You can a lso press the accelerator pedal down
to inc rease your speed, e.g . if yo u want to
pass someone . The speed you saved ea rlier
will resume as soon as you release the acceler­
ator peda l.
If , however, you exceed your saved speed by
5 mph ( 10 km/h) for longe r than 5 minutes,
the cruise cont ro l w ill tu rn off tempora rily .
The symbol will go o ut but the saved speed
will be retained .
On the ro ad 77
Presetting your speed
You can preset your desired speed while the
vehicle is not moving.
"' Turn on the ignition.
"' Pull lever into position
(D c:> page 76,
fig . 75.
"' Press the leve r in the 0 or 0 direction to
increase or decrease your speed.
"' Re~asethelevertosave thatspeed.
This function makes it possible, for example,
to save the speed you want before dr iving on
the highway. Once on the h ighway, act ivate
t h e cr uise con trol by pulling the lever toward
(D .
Switching the system off
Temporary deactivat ion
"' Press the brake pedal, or
"' Keep the cl utch pedal pressed down longer ,
or
"' Press the lever into position @(not clicked
into place)
¢page 76, fig . 75, or
"' Drive for longer than 5 minutes at more
than 5 mph (10 km/h) above the stored
speed.
Switching off completely
"' Press lever into position @(clicked into
place), or
"' Switch the ignit io n off.
The system retains the saved speed if you de­
activate the cruise control temporar ily. To re­
sume the saved speed, re lease the brake or
clutch pedal and pull the lever to position
(D.
Switching the ignit ion off erases the saved
speed.
A WARNING
You shou ld only return to the saved speed
if it is not too fast for the current traffic
conditions -ris k of an accident!

78 On the road
Audi magnetic ride
Applies to vehicles: with mag netic r ide
Damping can be adjusted to the driver's pref­
erence and it adapts automatically to the cur­
rent driving situation.
Fig. 77 Cente r console: Switch for Audi magnetic r ide
.,. Press the switch ~ fig . 77 to turn spo rt set-
t ing o n or off.
Aud i magnetic ride is an electron ically con­
trolled damp ing system . Th is chassis system
assists the driver by adapting to the par ticular
situatio n th rough imper cep tible con trol p roc­
esses. The
damping provides individual mod u­
l ation of damping forces. For example, with
dampi ng cha racterist ics set to p rovide greater
comfort, damping is set somewhat harder for
a brief period only as required, when rounding
a curve and when braking.
Standard setting
Select the standard sett ing if you prefer a sus­
pension setting emphasizing comfort.
Sport setting
Select the sport setti ng if you prefe r a sporty
suspe nsio n setting . The LED in the sw itch
8
comes on to indicate spo rt setting .
@ Tips
The w arning/indicator light 8 in the in stru ­
ment cluster comes on in the even t of a
malfunction . Drive to the closest au thor ­
ized Audi dealer as soon as possible and
have the malfunction repaired.
Sport mode
Applies to vehicles: wit h Sport but ton
F ig . 7 8 Button in th e ce nte r console
.,. To switch sport mode on, press the button
in th e cente r console. The indicator light
t ur ns on .
.,. To swi tch spor t mo de off, press the bu tto n
in the center co nsole again. The indicator
light turns on .
A mo re agile and spo rty d riv in g style is po ssi­
ble when driving the vehicle in "sport mode".
T his mode affec ts thrott le response and the
sound of the engine and the damping charac ­
teristics of the Audi magnetic ride for dynamic
s uspension tuning .
@ Tips
If there is a malfunct ion in the retracta ble
rear spoiler* or the Audi magnetic ride*, it
may not be poss ible to activate sport
mode.
Acoustic parking system
Rear acoustic park assist
Applies to vehicles: wit h 4-channel acoustic park assist
Acous tic park assist gives a warning about
obstacles behind the vehicle.
Description
T he rea r acousti c park ass ist (4-cha nnel
a coustic park ass ist) determines the distance
of the vehicle from an obstacle using ultra­
son ic sensors. The sensors are in the rear
bumper. The volume a nd the pitch of the

chimes can be adjusted through the menu dis­p lay ~
page 24 .
The range a t which the sensors start to meas ­
ure is
about :
To the side
Center rear
Activation
2 feet (0.60 m)
5 feet (1.60 m)
The parking assist is activated when
r ev erse
g ear
is engaged . A b rief tone confi rms that
the system is activated .
Bac king up
Distance warning when backing up starts
when an obstacle is detected in the range of
the park assist system . As the d istance de­
creases, the time interva l between the audib le
tones becomes sho rter.
When the d istance is less than 1 foot (0 .30
m), the tone becomes cont inuous . At this
point you should stop backing up.
Please note that low objects already signalled
by a warning can disappear from the system's
detection range and w ill not continue to be
signalled.
Potential malfunction s
If a warning buzzer sounds for a few seconds
when the ignition is sw itched on, there is a
system malfunction w ith the aco ustic park as­
sist . If the malfunction persists unti l the igni­
tion is sw itched off , there will be no acoustic
warn ing at the next attemp t to activate the
system . Have the problem corrected.
Th ere is no confirmation tone when reverse
gear is engaged if there is a system ma lfun c­
tion .
For the park ing ass ist to operate, the sensors
must be kept clean and free of ice .
.8, WARNING
- Senso rs have b lind spots in which obje cts
cannot be detec ted . Pay speci al atten tio n
to small c hildren and animals. They can-
On th e ro ad 79
not always be detected by the sensors -
danger of an accident!
- The parking assist cannot replace the
driver's attention. The driver alone is re­
sponsib le for parking and similar driving
maneuvers. Always watch where you are
driving .
(D Note
Low obstacles already signa lled by a warn­
i ng can d isappear from the system's detec­
tion range as they are approached and w ill
not continue to be signalled . Objects such
as ba rrie r cha ins, trailer d raw bars, th in
painted vertica l poles, o r fences may not
be dete cted by the system -risk of dam­
age.
(D Tips
F o r the pa rking assist to operate, the sen­
sors m ust be kept clean and free of snow
a nd ice.

The park lock must only be engaged with the
vehicle
stationary c::> &.
To engage P and to remove the lever from th is
position, you must depress the release b utton
(button in the selector lever handle)
and si­
multaneously you must step on the brake
pedal.
R · re verse
I n th is position, reverse is engaged.
Reverse gear must only be engaged with the
veh icle
stationary and the eng ine runn ing at
id le speed
c::> ,&. .
To engage R, you have to depress the release
button
and s imultaneously step on the brake
pedal. In the R position, the back-up lights il­
lum inate with the ign ition on.
N • N eutra l
The transmission is in neutral in this position .
D -Norm al p osi tion f or d riving forwa rd
In this position, the forward gears are auto­ matica lly shifted up and down, depending on
engine load and vehicle speed.
To engage D from N, the brake peda l must be
depressed at speeds be low 5 km/h or when
the vehicle is stationary
c::> & .
In certain circumstances (driving in the moun­
tains for examp le) it can be beneficial to
switch temporarily to the manua l shift pro­
gram
c::> page 84 in order to adjust the gear
ratios to driving cond itions
manually.
S -Sport setting
The 5 se tt ing shou ld be selected for spor ty
d riving . The power reserves of the engine can
be fu lly exp loited through later upshifts.
To engage S from N, the brake pedal must be depressed at speeds be low 5 km/h or when
the vehicle is stationary
c::> & .
Tra n sm iss io n 81
A WARNING
- Never p lace the selector lever in the R or
P posit ion while the veh icle is moving -
risk of an accident!
- With the engine running, it is necessary
to hold the vehicle with the foot brake in all selector lever positions (except P and N), because even at idle speed the trans­
fe r of power is never completely inter­
rupted -the vehicle " creeps". If the vehi­
cle is stationary and the transmission is
engaged, the engine should never be
speeded up unintentionally (e .g. manual­
ly from under the hood). Otherwise the
veh icle w ill immediately start to move -
sometimes even if the park ing brake is
firmly applied - risk of an accident!
- Before you or other persons open the
hood and work on a running engine, the
selecto r lever must be moved to P and
the park ing brake applied f irmly - risk of
an accident! Follow the wa rning sticke rs
c::> page 174, Engine compartment.
(D Tips
If yo u have inadvertently shifted into N
while the vehicle is moving, you shou ld re­
move you r foot from the accelerator and
wait unt il the engine speed has dropped to
idle before shifting back to Dor 5 .
Selector lever lock
Applies to veh icl es: w ith S tronic
The selector lever lock prevents a gear from
being engaged accidentally and unintention­
ally setting the vehicle in mo tion.
F ig. 81 Selector lever locks

"rollback" 9 &,. Do not try to prevent the
vehicle from ro lling back by revving the en ­
gine wh ile it is in gear .
Starting on a h ill
.,. Apply the hand brake firm ly .
.,. With the eng ine in gear, gradua lly acce ler-
ate and release the hand b rake.
The engine can only be
s ta rt e d with the selec­
tor lever in P o r N
9 page 72 . At low ambient
temperatures (14 °F / -10 °C), it is only poss i­
b le to start the engine with the selector lever
in
P.
When parking on level gro und, it is sufficient
to p lace the selector lever in
P. On a steeply
sloping road, yo u should first app ly the park­
ing b rake firm ly and then place the selector
l ever in
P. This way, yo u do not overload the
pawl mechanism and it is eas ier to move the
selector lever out of
P .
A WARNING
- Never leave you r vehicle with the eng ine
running wh ile in gear . If you must leave
yo ur vehicle with the engine running, set
the parking bra ke and engage the pa rk
lock.
- Whe n the engine is running and the
t ransmission is in gear (D,
5 or R) or in
"tiptronic" mode, it is essentia l that you
stop the vehicle with the footbrake .
When idling, the t ransmission of power
does not stop completely- the vehicle
"creeps" .
- Do not accelerate when you change the
selector lever position with the vehicle
stationary and the engine r unning -risk
of an accident!
- Never place the selector lever in the R or
N position while the vehicle is moving -
risk of a n accide nt!
- If you have to bring your vehicle to a stop
wh ile on an incl ine, keep the foot brake
depressed all the way down so tha t the
vehicle does not start to roll backward .
You should never hold the vehicle using
the clu tch if you are going to be stopped
Tran sm iss ion 83
on an incl ine. If you do, the cl utch w ill
start to slip when it ove rheats ca used by
the constant overload. This is dangerous because if the vehicle starts to roll back­
ward, you co uld cause an acc iden t. If the
clutch should start to s lip, you w ill feel
the vehicle "jerk" and the se le ctor lever
disp lay w ill st art bl ink ing .
- Before driving down a steep slope, re­
duce your speed and shift i nto a lowe r
gea r with "tiptronic".
- Do not ride the bra kes o r apply the bra ke
pe dal too often or too long. Const ant
brak ing c auses the brakes to overheat
and substantially reduces b raking per ­
formance, increases braking d istance or
causes complete fa il ur e of the brake sys ­
tem.
Hill Descent Assist
App lies to vehicles : wit h S t ronic
Hill Descent Assist helps the driver when driv­
ing down inclines .
Hill Descent Assis t is activ ate d by pressing the
brake while descending when the se lec tor lev ­
er is in D/S. The
5 tronic transmission auto­
matically shifts down to a gea r su itable for
the incline. H ill Descent Ass ist attempts to
maintai n the current veh icle speed w hen the
braking occurs, as far as physical and techn i­
ca l limits allow. It may be necessary to adjust
the speed using the brakes .
Hill Descent Assist sw itches off when the in­
cli ne leve ls out o r when the gas peda l is p ress ­
ed.
On vehicles with cruise control *
9 page 76,
Hill Descent Assist is also act ivated when the
speed is set .
A WARNING
Hill Descent Ass ist cannot overcome physi­
cal limitations, so it may not be poss ible to
maint ain a constant vehicle speed under
all ci rcumst ances. A lways be re ady to ap­
p ly the brakes.