CADILLAC ELDORADO 1993 10.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine When to Check Check your tires once a month or more.
The Eldorado tire pressures
are:
0 Front - 28 psi (200 kPa)
Rear - 26 psi ( 179 kPa)
Recommended tire sizes are:
0 XGT4 Touring Design Blackwall or Whitewall (P225/60R16)
The ETC or (4.6L Sport Coupe) tire pressures are:
Front - 29 psi (200 kPa)
Rear - 29 psi (200 kPa)
307

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine Rust or dirt on a wheel, or on the parts to which it is fastened,
can
make wheel nuts become loose afkr a time. The wheel could
come off and cause an accident. When you change a wheel,
remove any rust or dirt from places where the wheel attaches to
the vehicle. In an emergency, you can use a cloth or a paper
towel to do this; but be sure to use a scraper or wire brush later,
if you need lo, to get all the rust or dirt off. (See “Changing a
Flat Til .’I in the Index.)
When It% Time for New Tires
One way to tell when
it’s time for new tires is
to check the treadwear
indicators, which
will
appear when your tires
have only
2/32 inch
(1.6 mm) or less of
tread remaining.
You need a new tire if:
0 You can see the indicators at three places around the tire.
0 You can see cord or fabric showing through the tire’s rubber.
0 The tread or sidewall is cracked, cut or snagged deep enough to show
0 The tire has a bump, bulge or split.
cord
or fabric.
The tire has a puncture, cut, or other damage that can’t be repaired
well because
of the size or location of the damage.
309

Downloaded from www.Manualslib.com manuals search engine Buying New Tires
To find out what kind and size of tires you need, look at the Tire-Loading
Information label.
The tires installed on your vehicle when it was new had a Tire
Performance Criteria Specification (TPC Spec) number on each tire’s
sidewall. When you
get new tires, get ones with that same TPC Spec
number. That way, your vehicle will continue to have tires that are
designed to give proper endurance, handling, speed rating, traction, ride
and other things during normal service on your vehicle. If your tires have
an all-season tread design, the TPC number will be followed by a
“MS”
(for mud and snow).
If you ever replace your tires with those not having a TPC Spec number,
make sure they are the same size, load range, speed rating and
construction type (bias, bias-belted or radial) as your original tires.
A CAUTION:
Mixing tires could cause you to lose control while driving. If you
mix tires of different sizes or types (radial and bias-belted
tires), the vehicle may not handle properly, and you could have
a
crash. Be sure to use the same size and type tires on all four
wheels.
It’s all right to drive with your compact spare, though. It was
developed
for use on your vehicle.
Uniform Tire Quality Grading
The following information relates to the system developed by the United
States National Highway Traffic Safety Administration which grades tires
by treadwear, traction and temperature performance. (This applies only
to vehicles sold in the United States.)

Downloaded from www.Manualslib.com manuals search engine Treadwear
The treadwear grade is a comparative rating based on the wear rate of
the tire when tested under controlled conditions on a specified
government test course. For example, a tire graded
150 would wear one
and a half
(1 1/2) times as well on the government course as a tire graded
100. The relative performance of tires depends upon the actual
conditions of their use, however, and may depart significantly from the
norm due to variations in driving habits, service practices and differences
in road characteristics and climate.
Traction - A, B, C
The traction grades, from highest to lowest are: A, B, and C. They
represent
the tire’s ability to stop on wet pavement as measured under
controlled conditions
on specified government test surfaces of asphalt
and concrete.
A tire marked C may have poor traction performance.
Warning: The traction grade assigned to this tire is based
on braking
(straight-ahead) traction tests and does not include cornering \
(turning)
traction.
Temperature - A, B, C
The temperature grades are A (the highest), B, and C, representing the
tire’s resistance to the generation of heat and its ability to dissipate heat
when tested under controlled conditions
on a specified indoor laboratory
test wheel. Sustained high temperature can cause the material of the tire
to degenerate and reduce tire life, and excessive temperature can lead to
sudden tire failure. The grade
C corresponds to a level of performance
which all passenger car tires must meet under the Federal Motor Vehicle
Safety Standard
No. 109. Grades B and A represent higher levels of
performance on the laboratory test wheel than the minimum required by
law.
Warning: The temperature grade for this tire is established for
a tire that
is properly inflated and not overloaded. Excessive speed, underinflation,
or excessive loading, either separately or
in combination, can cause heat
buildup and possible tire failure.
Those grades are molded
on the sidewalls of passenger car tires.
31 I

Downloaded from www.Manualslib.com manuals search engine While the tires available as standard or optional equipment on General
Motors vehicles may vary
with respect to these grades, all such tires meet
General Motors performance standards and have been approved for use
on General Motors vehicles. All passenger type
(P Metric) tires must
conform to Federal safety requirements in addition
to these grades.
meel Alignment and Tire Balance
The wheels on your vehicle were aligned and balanced carefully at the
factory to give
you the longest tire life and best overall performance.
In most cases, you will not need to have your wheels aligned again.
However,
if you notice unusual tire wear or your vehicle pulling one way
or the other,
the alignment may need to be reset. If you notice your
vehicle vibrating
when driving on a smooth road, your wheels may need
to be rebalanced.
Wheel Replacement
Replace any wheel that is bent, cracked or badly rusted. If wheel nuts
keep coming loose, the wheel, wheel bolts, and wheel nuts should be
replaced. If the
wheel leaks air out, replace it (except some aluminum
wheels, which can sometimes be repaired). See your Cadillac dealer if any
of these conditions exist.
Your dealer
will know the kind of wheel you need.
Each new
wheel should have the same load carrying capacity, diameter,
width, offset, and be mounted the same way as the one
it replaces.
If you need to replace any of your wheels, wheel bolts, or wheel nuts,
replace them only
with new GM original equipment parts. This way, you
will be sure to have the right wheel, wheel bolts, and wheel nuts for your
Cadillac model.
312

Downloaded from www.Manualslib.com manuals search engine ‘ 1 CAUTION:
Using the wrong replacement wheels, wheel bolts, or wheel nuts
on your vehicle can be dangerous. It could affect the braking
and handling of your vehicle, make your tires lose air and make
you lose control. You could have a collision in which you or
others could be injured. Always use the correct wheel, wheel
bolts, and wheel nuts for replacement.
Used Replacement Wheels
I
A CAUTION
Putting a used wheel on your vehicle is dangerous. You can’t
know how it’s been used
or how many miles it’s been driven. It I
could fail suddenIy and cause an accident. If you haw ~ II replace
a wheel use anew GM original equipment wheel. I
I
I
3 13

Downloaded from www.Manualslib.com manuals search engine UP
Tire Chains
APPEARANCE CARE u
1 314

Downloaded from www.Manualslib.com manuals search engine 3 15

Downloaded from www.Manualslib.com manuals search engine L
CLEANING THE INSIDE OF YOUR
Use a vacuum cleaner often to get rid of dust and loose dirt. wipe vinyl
with a
clean, damp cloth.
Your Cadillac dealer
has two GM cleaners -- a solvent-type spot lifter and
a foam-type powdered cleaner. They will clean normal spots and stains
very well.
Here are some cleaning tips:
0 Always read the instructions on the cleaner label.
Clean up stains as soon as you can -- before they set.
0 Use a clean cloth or sponge, and change to a clean area often. A soft
Use solvent-type cleaners in a well-ventilated area only. If you use
0 If a ring forms after spot cleaning, clean the entire area immediately
brush
may
be used if stains are stubborn.
them, don’t saturate the stained area.
or
it will set.
USING FON=WPE CLEANER ON FMRIC
0 Vacuum and brush the area to remove any loose dirt.
Always clean a whole trim panel or section. Mask surrounding trim
along stitch or welt lines.
316