light CADILLAC FLEETWOOD 1994 Manual Online

NOTICE:
Continuing to drive with worn-out brake pads could result in
costly brake repair.
Some driving conditions or climates may cause a brake squeal when the
brakes are first applied or lightly applied. This does not mean something
is wrong with your brakes.
Brake linings should always be replaced as complete axle sets.
Rear Drum Brakes
Your rear drum brakes don’t have wear indicators, but if you ever hear a
rear brake rubbing noise, have the rear brake linings inspected. Also, the
rear brake drums should be removed and inspected each time the tires
are removed for rotation or changing. When you have
the front brakes
replaced, have the rear brakes inspected, too.
Brake Pedal Travel
See your dealer if the brake pedal does not return to normal height, or if
there is a rapid increase in pedal travel. This could be a sign of brake
trouble.
Brake Adjustment
Every time you make a moderate brake stop, your disc brakes adjust for
wear.
If you rarely make a moderate or heavier stop, then your brakes
275

Khicle Storage
If you’re not going to drive your vehicle for 25 days or more, take off the
black, negative
(-) cable from the battery. This will help keep your battery
from running down.
Contact your dealer to learn how to prepare your vehicle for longer
storage periods.
HXOGEN BULBS
EXTERIOR MP HOUSINGS
I NOTICE:
Your Cadillac’s lamp housings are designed with small vents so
moisture will be removed when the lights are on, or after dri\
ving
for a short time.
If an excessive amount of moisture is present
which does not clear, see your Cadillac dealership for service.\

277

0. Remove the
socket by
.rotating it
counterclockwise
slightly, then
gently push and
rotate bulb
counterclockwise and remove it.
0 Once you have replaced the bulb just reverse the steps to reassemble
the cornering lamp.
Halogen Headlight Bulb Removal
Here’s how to change the bulb:
0 Rotate the
headlight housing
socket
counterclockwise
to unlock the
socket from the
lamp housing.
279

-
Gently remove
headlight housing
socket and bulb.
I
Disconnect the
socket from the
harness by
separating locking
clip.
280
-J
I
U
Li

0 Install new bulb
and socket and
connect the wiring
harness. Make sure
that harness
is
locked to bulb
socket.
NOTICE:
Do not touch glass portion of the new halogen bulb! The oil
from you fingers
will shorten the life of your new halogen bulb.
Install the headlight housing socket into the headlamp assembly.
TMLLIGHT BULB REPLACEMENT
Remove the upper
screw from the
bezel.
281

0
Gently tilt the top
portion
of taillight
housing out first,
and then gently
remove it.
Press the bulb
socket housing
lever and rotate the
socket housing
counterclockwise to
remove it. f U

0 To remove the bulb,
push it in and
rotate it
counterclockwise.
Install bulb and
socket into taillight
housing
by turning
it clockwise. Be
sure it locks into
place.
285

0 Once you have
installed the new
bulb and socket
into the housing,
just reverse the
steps to assemble
the taillight. Make
sure when installing
the chrome bezel
that
you insert the
two prongs at the
bottom first.
CENTER HIGH MOUNTED STOP LAMP
BULB REPLACEMENT
286
3
Ipi
I
I
-
i

NOTICE:
The wrong wheel can also cause problems with bearing life,
brake cooling, speedometer/odometer calibration, headlight
aim, bumper height, vehicle ground clearance, and tire or tire \
chain clearance to the body and chassis.
Used Replacement Wheels
299

1
Here are some cleaning tips:
Always read the instructions on the cleaner label.
Clean up stains as soon as you can -- before they set.
Use a clean cloth or sponge, and change to a clean area often. A soft
Use solvent-type cleaners in a well-ventilatcd area only. If you use
brush
may be used if stains are stubborn.
them, don’t saturate .the stained area.
If a ring forms after spot cleaning, clean the entire area immediately
or it will set.
Using Foam-Type Cleaner on Fabric
Vacuum and brush the area to remove any loose dirt.
Always clean a whole,trim panel or section. Mask surrounding trim
Mix Multi-Purpose Powdered Cleaner following the directions on the
along
stitch or welt lines.
container label.
Use suds only and apply with a clean sponge.
Don’t saturate the material.
Don’t rub it roughly.
As soon as you’ve cleaned the section, use a sponge to remove
the suds.
Rinse the section with a clean, wet sponge.
Wipe off what’s left with a slightly damp paper towel or cloth.
Then dry it immediately with a blow dryer or a heat lamp.
NO.TICE:
Bexareful with.a hair dryer or heat lamp. You could scorch the
fabric.
Wipe with a clean,cloth:
nl
oi
r
c -1
& .i
302