seat adjustment CHEVROLET CAMARO 1967 1.G Chassis Owner's Guide

STEERING 9-17

STEERING SHAFT

SHIFT TUBE

Fig.
34—Shift Tube and Steering Shaft

17.
Remove bearing adapter clip (fig. 34).

18.
Remove bearing adapter with bearing, and shift

tube spring. On automatic columns, remove spring

thrust washer (fig. 32).

19.
U necessary, press bearing out of bearing adapter.

20.
Withdraw shift tube assembly from lower end.

21.
Remove the lower bowl bearing from the top end of

the jacket by inserting a suitable length of pipe or

wooden rod through the lower end and tapping the

bearing out. This bearing may be reused in this

column or discarded. It may not be used as a re-

placement part in another column.

22.
Slide steering shaft lower bearing spring, plunger,/

tolerance
*
ring and sleeve assembly, and thrust

washer off upper end of shaft.

23.
If necessary, unwrap mesh cover from jacket.

24.
Remove flange clamp bolt and flange at bottom of

steering shaft, if so equipped.

Assembly—Column Mounted Powerglide Lever or

Floor Shift Column (Fig. 32)

1.
Apply a thin coating of lithium soap grease to all

friction surfaces.

2.
If lower shift bowl bearing was removed from jacket,

press bowl bearing into top end of jacket.

3.
If lower bearing was removed from adapter, press

lower bearing into adapter.

4.
On automatic columns, install spring thrust washer

on end of shift tube against lower shift lever.

5. Install shift tube spring and adapter on end of shift

tube and secure with bearing adapter clip (fig. 34).

6. Slide shift- tube into position through lower end of

jacket.

7. Attach the back-up lamp/neutral start switch, if so

equipped, to the jacket using the same nuts removed

during disassembly. Install these nuts loosely; the

switch must be adjusted after column is installed in

the vehicle.

NOTE:
If the steering shaft assembly, mast

jacket, upper bearing housing assembly, or lower

bearing assembly has been replaced, the com-

ponent stack-up in the column will be different.

Replace the lower plastic injected tolerance ring

and bearing preload spring with the necessary

tolerance ring kit as described below.

8. Slide thrust washer, tolerance ring kit, plunger, and

kit spring into position from top of steering shaft.

9. Slide steering shaft assembly into position through

lower end of jacket.

10.
On automatic columns, if upper shift lever spring

was removed, press a new upper shift lever spring

into shift lever bowl. Be sure spring is seated in

bowl pocket.
Fig.
35—Tolerance, Ring Kit—First Adjustment

11.
Insert the upper bearing housing assembly and the

turn signal switch assembly into the cover, feeding

the signal switch wires through the back of the cover.

12.
Align the signal switch and bearing housing holes

with the holes in the cover. Install three mounting

screws through the holes.

13.
Slide three springs onto screw ends at rear of cover

and place lockplate in position over screws and

springs. Turn screws three turns into lockplate.

14.
Feed switch wire through the shift lever bowl and

place upper end assembly on top of bowl.

15.
Place the shift lever bowl and signal switch cover

assembly on top of jacket, aligning the tangs on the

RING KIT

OUTER SECTION

Fig.
36—Tolerance Ring Kit—Final Adjustment

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-18

I.D. of the lockplate with the slots in the top of the

jacket.

16.
Lock upper end assembly into position by pushing 18.

down on the cover assembly and rotating assembly

fully clockwise. Tangs on lock plate must engage

slots in jacket. 19.

17.
Tighten three turn signal switch mounting screws in
a gradual criss-cross sequence to avoid cocking the

lockplate.

Screw tolerance ring kit sections together leaving

enough inner edge exposed for later adjustment as

shown in Figure 35.

Slide wave washer and thrust washer over steering

shaft against upper bearing housing.

17 15 13 11 9 7 5 3

34 V33 29 27 26

36 35 32 3130 28

46 45 44 -43 42

Fig.
37—Tilt Steering Column—Exploded View

1.
Cover

2.
Steering Wheel Nut

3. Nut

4.
Seat

5.
Race

6. Screw

7. Turn Signal Switch

8. Bearing Assembly

9. Spring Retainer

10.
Lock Shoe Pin

11.
Shoe

12.
Bearing Housing
13.
Pivot Pin

14.
Shoe Springs

15.
Spring

16.
Release Lever Pivot

Pin

17.
Release Lever

18.
Bearing

19.
Upper Shaft

20.
Spring

21.
Sphere

22.
Wave Washer

23.
Lower Shaft
24.
Tilt Spring

25.
Screw

26.
Support

27.
Lock Shoe Guide

Pin

28.
Stop Plate

29.
Screw

30.
Retainer

31.
Thrust Washer

32.
Lock Plate

33.
Wave Washer

34.
Shift Lever Spring
35.
Shift Bowl

36.
Shroud

37.
Mast Jacket

38.
Dash Seal

39.
Shift Tube Assembly

40.
Adapter

41.
Bearing

42.
Tolerance Ring Kit

43.
Washer

44.
Retaining Ring

45.
Bolt

46.
Flange

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-23

Fig.
47—I retaliating Spherical Joint Spring

upper shaft should be on the same side as the

flat on the lower shaft.

d. Install the upper shaft with spheres into the lower

shaft.

e. Insert the joint preload spring through the

spheres into the lower shaft. Using the upper

shaft to hold the spring in place, carefully feed

the spring into the upper shaft joint with a narrow

bladed screwdriver (fig. 47).

17.
Slide the race and bearing over the top of steering

shaft and install shaft in shift tube from upper end.

Carefully guide shaft through shift tube, taking care

not to tear or push out foam seal cemented inside

lower end of shift tube.

18.
Install tilt control lever and, holding lock shoes in

disengaged position, assemble bearing housing on the

shaft over the support until pivot pin holes line up.

19.
Secure bearing housing in position by pressing in the

pivot pins.

20.
Place housing in full up position and install tilt

spring, tapered end first. Install tilt spring retainer

using screwdriver in retainer slot.

21.
Install turn signal switch with three mounting

screws. Place short length screw in top position

above lock shoes.

NOTE:
If the steering shaft, adapter, mast

jacket, support or bearing housing has been,

replaced, the component stack-up in the column

will be different. Replace the lower plastic in-

jected tolerance ring and the lower bearing pre-

load spring with the necessary tolerance ring

kit as described below.

22.
Slide kit spring, tolerance ring kit, washers, and

retaining ring on steering shaft from lower end.

Seat retaining ring in steering shaft groove.

23.
Screw tolerance ring kit sections together leaving

enough inner edge exposed for later adjustment as

shown in Figure 35.

24.
Install inner race, inner race seat, and bearing lock-

nut on end of steering shaft, using locknut wrench

ToolJ-22599 (fig. 39).

25.
Remove any remaining looseness from internal col-
umn stack-up by unscrewing inner tolerance kit ring

section; then screw inner ring section back in 1/8 to

1/4 turn (fig. 36).

26.
Tighten bearing locknut installed in Step 24 above

until the torque required to rotate the steering shaft,

with the housing in the mid position, is 23 lb. in.

27.
Touch the outer surface of the tolerance ring kit at

several locations with a hot soldering iron to melt

the threads of the inner and outer sections together.

28.
Check to insure hazard warning switch is pushed in.

Remove tilt release control lever and install turn

signal switch cover using turn signal cover installer

Tool J-21853 (fig. 48). On automatic column, be sure

key in the cover is aligned with keyway in bearing

housing.

29.
Place turn signal control lever in position and se-

cure with mounting screw. Screw tilt release control

lever in. Screw hazard warning knob in.

30.
On automatic columns, place transmission shift con-

trol lever in position and insert lever retaining pin.

31.
On automatic columns to be installed in a Camaro,

insert the bulb and cap into the turn signal switch

housing (fig. 33). Slide pointer into position in bowl.

Install dial and dial retainer with mounting screws

removed during disassembly.

32.
Install steering shaft flange on bottom of shaft and

secure with flange bolt.

33.
Remove column from vise. Pull wires back against

column leaving a small amount of slack. Snap wiring

protector into position. Be sure enough slack re-

mains in wires to allow column head to tilt to full

up position.

34.
If mesh cover was removed, wrap mesh cover around

mesh portion of jacket and secure with friction or

electricians tape.

35.
Slide cancelling cam and cancelling cam spring on

upper end of shaft.

Disassembly—Standard Corvette Column (Fig. 49)

1.
Place column on a suitable work bench.

2.
Remove upper bearing preload spring and cancelling

cam from end of column.

3.
Slide escutcheon clear of wiring protector and re-

move protector.

4.
Remove turn signal lever retaining screw and re-

move lever. Push hazard warning knob in; unscrew

and remove knob.

Fig.
48—Installing Turn Signal Switch Cover Using

Signal Switch Installer Tool J-21853

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-25

\
£$&+
SIGNAL SWITCH

^ ^-BEARING

UPPER FLANGE^
HOUSING

COVER

»,

ESCUTCHEON
"^^^^^fr

Fig.
51-Assembling Upper End

13.
If necessary, remove two seals from lower end I.D.

of jacket.

14.
If necessary, unwrap mesh cover from jacket.

Assembly—Standard Corvette Column (Fig. 49)
RING KIT V

INNER SEaiON-n 1

\
[1

3

^^•-
'^p|§<sP"
• • ; ''•'- "; ' '-'""••-•• ••'•. " . ; /

W- - V: -: ';'^ /

W ^-RI^G KIT

OUTER SECTION

Fig.
52—Tolerance Ring Kit—First Adjustment

14.
Touch the outer surface of the tolerance ring kit at

several locations with a hot soldering iron to melt

the threads of the inner and outer ring sections

together.

1.

4.

5.

6.
of lithium soap grease to all 15. Place turn signal switch lever in position and secure

10.

11.

12.

13.
Apply a thin coating

friction surfaces.

If seals were removed from lower end I.D. of jacket,

cement two new seals into position.

If lower bearing assembly was removed, press new

lower bearing into position at lower end of mast

jacket.

Slide thrust washer, tolerance ring kit, plunger, and

new kit spring into position from top of steering

shaft.

Install flange and flange bolt on lower end of steering

shaft.

Carefully slide steering shaft into lower end of mast

jacket.

Assemble upper bearing housing and turn signal

switch into cover and secure entire assembly to mast

jacket upper flange with three signal switch mounting

screws as shown in Figure 51.

Feed turn signal switch wires through escutcheon.

Slide escutcheon and upper assembly onto upper end

of column. Secure upper flange to column with three

mounting bolts.

Screw tolerance ring kit sections together leaving

enough inner edge exposed for later adjustment (fig.

52).

Slide wave washer, thrust washer, and "C" retaining

ring loosely into place at top of shaft.

Complete installation of "C" retaining ring using

snap ring installer Tool J-22659 as shown in Figure

50.
Be sure retaining ring is completely seated into

steering shaft groove.

Remove any remaining looseness from internal col-

umn stack-up by unscrewing inner tolerance ring kit

section; then screw inner kit section back in 1/8 to

1/4 turn. See Figure 53.
with screw. Screw hazard warning knob into position.

16.
Pull signal switch wires flat against column, install

wiring protector, and slide escutcheon into position.

17.
If mesh cover was removed, wrap mesh cover around

mesh portion of mast jacket and secure with friction

or electricians tape.

18.
Install spring and cancelling cam on end of shaft.

RING KIT

OUTER SECTION

fig.
53-Tolerance Ring Kit-Final Adjustment

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-31

Fig.
63—Freeing Ball Stud

rod threads with EP Chassis lube and install ends on

tie rod making sure both ends are threaded ah equal

distance from the tie rod.

2.
Make sure that threads on ball stud and in ball stud

nuts are perfectly clean and smooth. Install neoprene

seals on ball studs.

NOTE: If threads are not clean and smooth,

ball studs may turn in tie rod ends when at-

tempting to tighten nut.

3.
Install ball studs in steering arms and relay rod.

4.
Install ball stud nut, and install cotter pins. Lubri-

cate tie rod ends.

5.
Adjust toe-in as described in Section 3.

NOTE: Before locking clamp bolts on the rods,

make sure that the tie rod ends are in alignment

with their ball studs (each ball joint is in the

center of its travel). If the tie rod is not in

alignment with the studs, binding will result.

RELAY ROD-ALL MODELS EXCEPT CORVETTE

Removal

1.
Remove inner ends of tie rods from relay rod as

described under Tie Rod - Removal.

2.
Remove cotter pin and nut from relay rod ball stud

attachment at pitman arm.

3.
Detach relay rod from pitman arm. Shift steering

linkage as required to free pitman arm from relay

rod.

4.
Remove cotter pin and nut from idler arm and re-

move relay rod from idler arm.

Installation

1.
Install relay rod to idler arm, making certain idler

stud seal is in place, then install and tighten nut.

Advance nut just enough to align castellation with

cotter pin hole and install pin.

2.
Raise end of rod and install on pitman arm. Secure

with nut and cotter pin.
3.
Install tie rod ends to relay rod as previously

described under Tie Rods. Lubricate tie rod ends.

4.
Adjust toe-in (see Section 3) and align steering wheel

as described previously in this section under Steer-

ing Wheel Alignment and High Point Centering.

RELAY ROD-CORVETTE

Removal

1.
Remove steering damper from relay rod as outlined

under Steering Damper-Removal. Remove anchor

bracket from relay rod by disconnecting two mount-

ing bolts.

2.
Remove inner ends of tie rods from relay rod as

described under Tie Rod--Removal.

3.
Remove cotter pin from end of relay rod at pitman

arm ball stud attachment, and remove stud nut.

4.
Tap brJl stud out of pitman arm and lower relay rod.

5.
Remove cotter key and nut from idler arm and re-

move relay rod from idler arm. Remove washer and

seal from idler arm.

Installation

1.
Place relay rod on idler arm stud, making certain

idler stud seal and washer are in place, then install

and tighten nut. Advance nut just enough to align

castellation with cotter pin hole and install pin.

2.
Install new seal and clamp over ball at end of pitman

arm.

3.
Install inner spring seat and spring to relay rod.

4.
Raise end of rod and install on pitman arm.

5.
Install spring seat, spring, and end plug.

6. Tighten end plug until springs are compressed and

plug bottoms, then back off 3/4 turn plug amount

necessary to insert cotter pin. Insert cotter pin to

lock adjustment.

7.
Install tie rod ends to relay rod as previously de-

scribed under Tie Rods.

8. Lubricate tie rod ends and pitman arm to relay rod

ball joint.

9. Install steering damper bracket and tighten bolts.

Install damper as outlined under Steering Damper--

Installation.

10.
Adjust toe-in and align steering wheel as described

previously in this section.

IDLER ARM

Chevrolet, Chevelle, Comoro, and Corvette (Fig. 62)

Removal

1.
Remove idler arm to frame nut, washer, and bolt.

No washer is used on Corvette.

2.
Remove cotter pin and nut from idler arm to relay

rod ball stud.

3.
Remove relay rod from idler arm by tapping relay

rod with a hammer using a heavy hammer as a

backing.

4.
Remove idler arm.

Installation

1.
On Chevrolet, place seal in position on idler arm

stud; position stud up through frame, and secure with

lock washer and nut.

2.
On Chevelle, Camaro, and Corvette, position idler

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-37

NUT

Fig.
69—Control Valve Ball Stud Seal Replacement

(Service Type)

4.
Center the ball stud, seal and clamp at opening in

adapter housing, then install spacer, bolt and nut.

Removal

1.
Raise the front of the vehicle off the floor and place

it on stands.

2.
Remove the relay rod to control valve clamp bolt.

3.
Disconnect the two pump to control valve hose cdn-

nections and allow fluid to drain into a container,
then disconnect the two remaining valve to power

cylinder hoses.

4.
Remove the retaining nut from the ball stud to pitman

arm connection and disconnect the control valve

from the pitman arm.

5. Turn the pitman arm to the right clear of the control

valve and unscrew the control valve from the relay

rod.

6. Remove the control valve from the vehicle.

Installation

1.
Install the control valve on the vehicle by reversing

the removal procedure.

2.
Reconnect the hydraulic lines, fill the system with

fluid and bleed out air using the procedure outlined

under "Maintenance and Adjustments/' Grease ball

joint.

POWER CYLINDER (Fig. 70)

Chevy II and Corvette

Removal

1.
Disconnect the two hydraulic lines connected to the

power cylinder and drain fluid into a container. Do

not reuse.

2.
Remove cotter pin, nut, retainer and grommet from

power cylinder rod attached to the frame bracket.

3.
Also remove grommet and retainer from bracket if

replacement parts are required.

1.
Snap Ring

2.
End Plug and

Lube Fitting

3.
"O" Ring
Fig.
70—Power Cylinder—Exploded View

4.
Spring

5. Spring Seat

6. Ball Stud
7. Ball Seat

8. Ball Stud Seal

9. Piston Body
10.
Piston Rod Seal

11.
Backup Washer

•12.
Scraper Element
13.
Piston Rod Scraper

14.
Snap Ring

15.
Piston Rod

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-39

4.
Remove cotter pin, nut and ball stud at relay rod.

5. Remove the power cylinder from the vehicle.

Inspection

1.
Inspect the seals for leaks; if leaks are present,

replace the seals using the procedure outlined under

"Disassembly."

2.
Examine the brass fitted hose connection seats for

cracks or damage and replace if necessary.

3.
For service other than ball seat or seal replacement

and ball stud removal, replace the power cylinder.

4.
Check the frame bracket parts for wear.

Disassembly

1.
To remove the piston rod seal remove the snap ring;

then pull out on the rod, being careful not to spray

oil.

2.
Remove the piston rod scraper and scraper element,

back up washer and piston rod seal from the rod.

3.
At the ball stud end of the cylinder, remove the ball

stud seal.

4.
Remove the snap ring retaining the end plug with the

lube fitting.

5. Push on the end of the ball stud and remove the end

plug, spring, spring seat and ball stud.

6. Remove the "O" ring seal from the top lip of the

power cylinder ball stud opening.

7. If the ball seat is to be replaced, it must be pressed

out using Tool J-8937.

Assembly

1.
Reassemble the piston rod seal components by re-

versing the disassembly procedure. Apply a thin
coat of Lubriplate or equivalent on the inner sur-

faces of the seal and scraper before assembly.

2.
Reverse the disassembly procedure when reassem-

bling the ball stud.

3.
In each case be sure that the snap ring is securely,

seated in the ring groove.

Installation

1.
Install the power cylinder on the vehicle by reversing

the removal procedure.

2.
Reconnect the two hydraulic lines, fill the system

with fluid and bleed out air using the procedure out-

lined under "Maintenance and Adjustments." Grease

ball joint.

POWER STEERING HOSES

When servicing the power steering hoses be sure to

align the hoses in their correct position as shown in

Figure 71. On Chevelle models with 396 engine, install

the upper hose so that there is at least .6 inch clearance

between the hose and the Delcotron or the inner fender

skirt.

It is important that the power steering hoses be in-

stalled correctly. Hoses installed out of position may be

subjected to chafing or other abuses during sharp turns.

Always make hose installations with front wheels in

straight ahead position. Do not twist hoses unneces-

sarily during installation.

CAUTION: Do not start engine with any power

steering hose disconnected.

CHEVROLET CHASSIS SERVICE MANUAL

WHEELS AND TIRES 10-5

WHEELS

The wheel and tire assembly should be removed from

vehicles equipped with disc brakes to properly perform

balancing operations. This is necessary due to drag of

the spring loaded brake shoes on the disc.

Static Balancing (W/Tire)

Static Balance (still balance) is the equal distribution

of weight of the wheel and tire assembly about the axis

of rotation so that the assembly has no tendency to rotate

by
itself.
Static unbalance causes the pounding action of

the front wheels that is called "tramp".

To correct static unbalance (front and rear): The

quickest and best methods to correct static unbalance

are through the use of wheel balancers which are com-

mercially available. Refer to the Information and in-

structions included with these balaricers.

Dynamic Balancing (W/Tire)

Dynamic Balance (running balance) requires the wheel

to be not only in static balance, but balanced and running

smoothly while turning on an axis which runs through the

centerline of the wheel and tire perpendicular to the axis

of rotation.

The quickest and best methods of testing and correcting

dynamic unbalance are by the use of dynamic wheel

balancers which are commercially available. These bal-

ancers include all necessary information on where and

how the balancing weights should be placed. The follow-

ing information, however, will help in the correction of

dynamic balance.

NOTE:
Before attempting to balance the

wheels, check to be certain that no foreign

matter has been trapped in the wheel ventila-

tion slots or in the accessory wheel discs. This

is especially important if the vehicle has been
run in soft mud and then parked in freezing

weather.

When a wheel that is statically unbalanced is dynam-

ically in balance the dynamic balance can be retained

while correcting "the static balance by installing the cor-

rective weights so that half of the weight required is

placed on the inner edge of the rim and the other half

on the outer edge of the rim.

Dynamic unbalance can be corrected without destroying

static balance by installing weights so half of weight

required for dynamic balance is placed on the rim op-

posite the heavy point, while the other half is placed 180°

away and on the opposite side of the rim.

NOTE:
Vehicles with wire wheel covers should

have the wheels balanced with the wire wheel

covers installed on the wheels.

Run Out (W/OTire)

The wheels should not run out (wobble) more than

1/16" as measured on the side of the rim at the base

of the tire. Excessive run-out is the result of a bent

wheel, an improperly mounted wheel, worn knuckle bear-

ings or steering connections. These parts should be

checked for correct adjustment, proper alignment and

wear whenever excessive run-out is encountered.

The wheels should also run concentric with the steering

knuckle spindle within 1/16 inch as measured on the tire

bead seat of the rim with the tire removed.

Wheel run-out, eccentricity and balance are closely

associated with steering and front wheel alignment.

Further information on these subjects will be found under

"Suspension".

Cleaning Aluminum Wheels

Do not use wire brush or abrasive cleaners when

cleaning wheels. Use only cleaners that will not react

with aluminum.

SERVICE OPERATIONS

TIRES

Removal

Dismounting tubeless tires presents no problems if the

correct procedures are used and the following precau-

tions observed.

1.
Remove the valve cap and valve core. Let out all the

air.

2.
Press the inner side of the tire into the rim well.

Use bead loosening tool or if regular tire irons are

used, take particular care not to injure or tear the

sealing ribs on the bead.

CAUTION: Never use tire irons with sharp

edges or corners.

3.
Using tire irons on the opposite side, remove bead,

taking small "bites" around the rim.

4.
Turn the tire over, and use two tire irons, one be-

tween the rim flange and the bead to pry the rim

upward, the other iron to pry outward between the

bead seat and the bead.
Installation

Extreme care must be exercised to prevent injury to

the sealing bead and circumferential bead when forcing

tire over rim.

1.
Apply a light film of Ruglyde or other suitable rubber

lubricant to sealing bead of tire.

NOTE:
The use of excessive lubrication may

lead to rim slippage and subsequent breaking of

air seal.

2.
Carefully mount the outer bead in usual manner by

using tire irons, taking small "bites" around rim,

being careful not to injure the tire bead.

CAUTION: DO NOT use a hammer, as damage

to the bead will result.

3.
Install the inner bead in the same manner.

NOTE:
If a seal cannot be effected in the fore-

going manner with the rush of air it can be

, accomplished by applying to the circumference

of the tire a tire mounting band or heavy sash

cord and tightening with the use of a tire iron.

On tire mounting machines, bouncing the tire

assembly is not required. The tire should be

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 12

ELECTRICAL-BODY AND CHASSIS

CONTENTS
OF
THIS
SECTION

Page
Page

System 12-1

Instruments and Gauges 12-21

Directional Signal 12r40
Windshield Wipers and Washers 12-44

Wiring Diagrams 12-56

Special Tools 12-60

LIGHTING SYSTEM

INDEX

Page

General Description
!2-i

Maintenance and Adjustments
•.................. 12-2

Headlamp Adjustment......................
12-3

Headlamp Panel Travel Adjustment.
12-5

Service Operations.
. . .. 12-5

Front Lighting
12-5

Headlamp
. 12_5

Parking Lamp
12-5

Fender Lamp
. 12_^

Headlamp Panel
12-8

Headlamp Panel Motor
^2-9

Rear Lighting
l2-10

Tail, Stop and Directional Lamps
12-10
Page

Backing Lamps
12-14

License Plate Lamp
12-14

Automatic Transmission Quadrant Lamp
12-14

Seat Separator Console Lamps
. 12-15

Lighting Switch
. . 12-15

Wiper Switch.
12-15

Stoplight Switch
12-15

Dimmer Switch
12-15

Backing Lamp Switches
12-15

Neutral Safety Switches
12-17

Parking Brake Alarm Switch
................. 12-19

Instrument Panel Compartment Lamp/Switch
12-19

Cirgarette Lighter
12-19

GENERAL DESCRIPTION

.
The lighting system includes: the main lighting switch,

stop light, dimmer, and backing lamp switches, head-

lamps, parking lamps, stop, tail and directional lamps,

instrument illumination and indicator lamps, and the

necessary wiring to complete the various circuits. A

fuse panel provides convenient power take offs and fuse

clips for the appropriate circuits (fig. 1).

Chevrolet and Chevelle headlamp installation is all

new in that the headlamps are located in the radiator

support with adjusting screws and springs. Eliminating

the need for having separate headlamp housings. Chev-

rolet and Chevelle headlamp retainers and springs are

interchangeable.

Chevy n headlamp housings are new because of revised

front end styling and Corvette front end lighting is basi-

cally carryover.

Front fender lamps have been added as an option for

Chevrolet models and as standard equipment on Caprice

series.

Camaro models use single headlamps and the Rally

Sport model headlamps are covered by a retractable

section of the grille when lamps are not used. The sec-

tion of the grille covering the headlamps folds back when

lights are required; the headlamps are stationary. The

covering is retracted by a small electric motor mounted

to the headlamp housing. The headlamps are automat-

ically uncovered when the headlight switch is pulled "ON"

for illumination. If at any time the electrical circuit

becomes inoperative, the lamps can be uncovered manu-

ally. The ignition switch must be
"ON"
in order to close

the headlamp doors.

Parking lamp for Chevelle and Chevrolet models are
new due to revised front end sheet metal and bumper

styling. Parking lamps are located in the bumper on

Chevrolet, Chevelle and Chevy n models

Camaro parking lamps are located in the radiator

grille except for the Rally Sport models on which the

parking lamps are in the valance panel. For styling

reasons, the lens is white and an amber glass bulb is

used. All Camaro parking lamps require a separate

ground wire to assure a good ground contact because of

the plastic grille and painted contact surfaces.

The Chevrolet tail, stop, and directional lamps are in

one housing with a three section lens design on Impala

and Caprice sedans. The center lens for Impala series

is the back-up lamp. The center lens on the Caprice is

a tail lamp with the back-up lamps being located in the

rear bumper. Chevrolet station wagons have three indi-

vidual housings with three lenses, the center lamp being

the back-up. Biscayne and Bel-Air sedans have a single

housing and lens for tail, stop, and directional lamp with

a similarly constructed back-up lamp inboard and adja-

cent to it.

Chevelle tail, stop, and directional lamps are a single

lens design that follows through with the rear fender

styling. The back-up lamp is located in r.ear bumper.

Camaro models except Rally Sport have tail lamps

with integral back-up lamps mounted inboard of the rear

fenders between the trunk opening and bumper. The

Rally Sport model has dual tail lamps in the rear housing

and valance mounted back-up lamps.

Corvette, Chevy n, and Corvair tail and directional

signal lights are carryover. The Corvette has new back-

up lamps center mounted above the license plate opening.

CHEVROLET CHASSIS SERVICE

ELECTRICAL-BODY AND CHASSIS 12-8

is inserted through radiator support opening.

Remove two screws retaining lamp assembly to

lower sheet metal.

Remove three screws retaining lamp assembly to

lender.

To replace lamp assembly, reverse removal proce-

dure and check operation of the unit.
is aligned with flat on pivot shaft. Install stop lock

bolt and torque bolt to 45-60 in, lbs. Make sure that

side-to-side panel alignment is not changed when in-

stalling and tightening the stop.

CAUTION: Do not exceed specified torque

when tightening stop lock bolt.

HEADLAMP PANEL REPLACEMENT-CORVETTE

Refer to Figure 13 for Panel Mounting details.

1.
Remove engine compartment hood as outlined in

Section 1.

2.
Actuate headlamp panel to the open position.

NOTE:
In the event headlamp motor is inop-

erative, manual positioning of the panel can be

accomplished by turning the knurled knob at in-

board end of motor. As an assist in manual

operation of panel, apply light hand pressure to

panel in desired direction of rotation.

3.
Remove positive lead from battery terminal.

4.
Remove headlamp bezel retaining screws and bezel.

5. Remove the sealed beam housing unit as an assem-

bly - disconnect sealed beam leads at harness con-

nector and remove connector from sealed beam

leads;
remove the housing-to-panel retaining screws

and remove housing unit and wiring from panel.

6. Remove motor from panel pivot shaft - see motor

removal procedure. Then remove the panel stop

from panel inboard pivot shaft, and disconnect switch

lead wires from panel, support-mounted motor

switch.

7. Remove the panel retaining bolt access hole plugs

from inside the panel then rotate panel as required

and remove the retaining bolts and slide supports

from ends of panel pivot shaft. Remove bearing, felt

seal, retainer and washer from inboard pivot shaft.

8. Remove panel from its location by alternately disen-

gaging pivots from their retaining slots and with-

drawing unit forward through opening in body (fig.

14).

9. Loosen alien screw in spacer and disassemble parts

from the panel outboard pivot shaft.

10.
Install washer, retainer, felt seal, bearing and

spacer, in that order, to panel outboard pivot shaft.

Do not tighten spacer on shaft at this time.

11.
Position panel in body opening and index panel pivot

shafts in retaining slots; then loosely install support

retaining bolts.

12.
Install washer, retainer, felt seal, bearing and sup-

port, in that order, to panel inboard pivot shaft, and

loosely install support retaining bolts. -

13.
Check side-to-side alignment of panel, making sure

that there is no panel-to-body contact; position

spacer snugly against bearing; then tighten spacer

seat screw to 30-50 in. lbs.

14.
Install stop on panel inboard shaft so that it rests

against bearing, being sure that index mark on stop
15.
Check and align panel to body as follows:

a. Tighten panel pivot support bolts snugly but still

allowing panel to" be moved by applying hand

pressure.

b.
Position panel to the closed position and align

with body so that all surfaces are flush.

c. With the panel in the closed position the outboard

access hole is aligned with the forward bolt head.

Tighten this bolt with the panel in the closed

position - access to bolt head can be obtained by

working through opening between the hood and

body.

d. Rotate panel to obtain access to each bolt head

and torque bolts to 100-140 in. lbs.

e. Connect switch lead wires to support-mounted

limit switch.

16.
Install seaLed beam housing unit and at the same time

position sealed beam lead wires through panel out-

board pivot shaft. Install housing unit retaining

screws and install lead wires in connector, making

sure to match colors between harness and connector.

17.
Install motor assembly - see motor replacement

procedure.

18.
Connect positive lead to battery terminal.

19.
Adjust headlamp panel as outlined under "Headlamp

Panel Travel Adjustment".

20.
Adjust headlamp aiming as outlined under "Headlamp

Adjustment".

21.
Install headlamp bezel and engine compartment

hood - refer to Section 1 for hood installation.

Fig.
14
- Headlamp Panel Removal (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL