Chassis sheet metal CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

HEATER AND AIR CONDITIONING 1A-10

PLATE RETAINERS

CORE BRACKET SCREWS

Fig.
18—Corvette Heater Core Removal

7. Place a protective covering (waterproof if possible)

over the carpeting under the heater.

8. Remove the two bowden cables from the instrument

panel and disconnect the wiring connectors from the

blower switch and from the resistor.

9. Carefully work the heater assembly out from beneath

the dash.

Core Removal

1.
Remove the heater assembly as described above.
2.
Remove the sheet metal nuts which retain the core

mounting plate to the core housing.

3.
Remove the screws attaching the core brackets to

the core mounting plate and separate the core and

plate. .

Installation

1.
Assemble the core to plate with non-hardening

sealer. Attach the core mounting screws.

2.
Attach the core and plate assembly to the case with

the two sheet metal nuts. The assembly is ready for

installation as described below.

Heater Assembly Installation

1.
Carefully position the heater assembly in place on

inner surface of dash panel, then install the blower

and air inlet assembly on heater studs extending

through to the engine side of the panel. Attach the

seven stud nuts.

2.
Install electrical connectors to the blower switch and

resistor and reinstall the bowden cables to the

instrument panel.

3.
Replace the blower electrical connectors.

4.
Replace the heater hoses. (See Figure 20)

5. Replace the battery and the radiator supply tank.

6. Refill the radiator and check for leakage.

7. Check heater operation and make control adjustments

as necessary.

8. Replace the console panels and the glove

compartment.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-48

Fig.
60-Condenser Mounting (Chevy II)

2.
Remove the bumper, bumper filler panel, grille,

grille support, hood lock catch support and catch as

described in Section 11, "Chassis Sheet Metal".

3.
Disconnect connectors at condenser inlet and outlet

tubes and remove screws attaching refrigerant line

holding clips to the condenser baffle.

4.
Remove bolts attaching condenser through radiator

' support and slide condenser to the left and out of

vehicle.

5. Reverse these steps to reinstall new condenser.

6. Evacuate and charge the system. Add one fluid oz.

of refrigerant oil after installing a new condenser.

Corvette

Replacement (Production Engine)

1.
Remove the hood from the car, first scribing the

hinge attachment location.

2.
Purge the system of refrigerant.

Fig.
61—Condenser Mounting (Cdrnaro)
Fig.
62—Condenser Mounting (Corvette)

3.
Disconnect the inlet line connection at the condenser

inlet and the outlet line at the receiver-dehydrator.

Cap the receiver-dehydrator immediately.

4.
Remove the screws attaching the condenser to the

radiator support and carefully lift the unit from the

car.

5. Remove the receiver-dehydrator from the old con-

denser and install it, using a new "O" ring, on the

new condenser.

6. Set new condenser in place on the radiator support

and install the attaching screws, torquing them to

20 lbs. ft.

7. Make the inlet and outlet connections, using new

"O"
rings, and torque 13 lbs. ft.

8. Evacuate, charge and check the system. Add one

fluid oz. of refrigerant oil after installing a new

condenser.

Replacement (Optional Engine)

Replacement procedure remains much the same for the

installation supplied with the optional engine except for

the location of the receiver-dehydrator. Follow the steps

given above except that the outlet line must be removed

at the receiver outlet. (See Figure 64.)

RECEIVER-DEHYDRATOR

The receiver-dehydrator should be replaced if it has

been damaged through an accident or if it leaks or be-

comes restricted or clogged. Do not attempt to repair

the receiver-dehydrator.

The receiver-dehydrator is merely a moisture collect-

ing device and a refrigerant storage area and is the least

likely component of the system to cause a malfunction.

If at any time when examining the compressor oil,

moisture is found or there is an indication of moisture

at the expansion valve needle, the receiver-dehydrator

should be replaced as follows (fig. 63):

NOTE:
If the receiver-dehydrator is to be re-

used, cap the inlet and outlet connections

immediately. When installing a receiver-

dehydrator, do not uncap the connections until

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-74

Fig.
108—Comfortron Power Servo Installation

4.
Disconnect heater' hoses from heater core (at

firewall).

5. Remove glove box door.

6. Remove glove box interior.

7. Disconnect right, left, and center air conditioning

outlet hoses from distributor duct.

8. Remove air distributor duct from heater

housing.

9. Disconnect hose and cable clamps from heater

housing.

10.
Remove the remaining three heater housing stud

retaining nuts (engine compartment) and one upper

retaining screw (inside vehicle).

11.
Pull the unit away from the firewall and out of the

car.

ADJUSTMENT

SCREW

Fig.
109—Mode Shift Vacuum Diaphragm
Fig. 110'—Compressor Mount—L-6 Engines (Typical)

12.
Remove heater.housing cover from heater housing.

13.
Remove heater core from heater housing cover by

removing four (4) retaining screws and two "U"

clamps.

14.
Remove heater core.

Installation

1.
Replace core in case using a non hardening sealer.

Attach the core clamps and retaining screws.

2.
Attach the heater housing cover to the housing.

3.
Position the unit against the firewall and attach

it with the retaining screw at the top of the case.

4.
Attach the sheet metal nuts to the case studs which

project through the firewall to the engine side.

5. Connect the control cables to the control doors and

case.

6. Attach the air distributor duct to the case.

7. Connect the left, right, and center outlet hoses.

8. Replace the glove box assembly.

9. Connect heater hoses to core tubes.

10.
Replace fender assembly.

11.
Fill cooling system and connect battery cable.

Camaro

Lower Heater Hose

Removal

1.
Drain radiator.

2.
Remove side mouldings and retainers.

3.
Remove lower fender attaching bolts.

4.
Remove skirt to fender and skirt to reinforcement

bolts.

5. pry the skirt away from the fender flange and away

from the firewall. Block the skirt (four inchlengtti

of 2 x 4) clear of the lower hose and proceed with

the hose replacement.

Installation

1.
Connect the hose.

2.
Remove the block, move the skirt into position and

install all attaching bolts.

3.
Replace fender attaching bolts and mouldings.

4.
Refill cooling system.

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-11

CLAYOfc

CAULKING

COMPOUND

Fig. 26-Window Rear Stop - Typical

Fig. 24—Checking Adjustment of Striker

3.
Adjust door as required. Location of hinge retaining

bolts may be seen in Figure 25 at "A". Do not allow

doors to hang on one hinge without support.

4.
Install trim pad and lubricate door "hold opens" and

hinges with Lubriplate or its equivalent.

NOTE:
After performing any door adjustment,

the window and door post should be checked for

alignment and adjusted as necessary. In addi-

tion,
never slam the door after adjustment with-

out first checking the door lock and striker plate

engagement. An adjustment may be necessary.

TRIM PANEL, AND INSIDE HANDLES

Figure 29 is an exploded view of integral arm rest,

inside handles, and trim panel fastenings.

Removal of trim panel may be accomplished as

follows:

1.
Remove two screws under arm rest.

2.
Using Tool J-7797, remove clips retaining window

crank and lock remote control as shown in Figure 28.
3.
Remove knob from door lock control by turning

counter-clockwise.

4.
Remove 2 screws retaining inside pull handle.

5. Remove sheet metal screws and special washers

retaining trim panel to door assembly.

6. Pull trim panel out. at bottom, tap bottom edge of

trim panel with hand to disengage from top of door.

Remove trim panel from vehicle.

WEATHERSTRIP

Figure
30
illustrates both 19437 and 19467 model door

COWL

Fig.
25-Door Adjustment Points
Fig.
27-Door Hinge

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-23

Fig.
50—Folding Top Lid Assembly

1.
Striker Shim

2.
Striker

3. Lock Assembly
4. Lid Assembly

5. Control Assembly

6. Weatherstrip Assembly
7. Hinge Shim

8. Hinge Assembly
9. Cable Assembly

10.
Cable Retainer

24.
Clean up excess material with Oleum spirits, prep-

sol or kerosene.

GAS TANK DOOR AND REAR TRIM PLATE

Figure 62 illustrates installation details of gas tank

door and rear trim plate.

Gas tank door and bezel may be replaced by removing

sheet metal screws located on inner circumference of

bezel.

Trim plate is retained by five special nuts which are

accessible from under right rear corner of vehicle.

REAR FILLER PANEL

Removal

1.
Remove rear license plate and license plate housing

as explained in Section 14.
2.
Remove tail pipes from mufflers.

3.
Remove ten screws holding filler panel to body

(fig. 62).

Installation

Reverse removal procedure.

SPARE TIRE MOUNT

Refer to Figure 63.

Removal

1.
Remove spare tire.

2.
Loosen pivot bolt lock nuts and turn pivot bolts out

of weld nuts in crossmember.

3.
Remove two screws retaining swivel bolt assembly

to body.

4.
Remove four bolts holding cover assembly to body.

CHEVROLET CHASSIS SERVICE

CORVETTE BODY 1B-40

Fig.
88—Applying Sealer to Frame

To replace panel, proceed as follows:

1.
Cut out damaged panel with a hacksaw blade and

thoroughly remove all dirt and paint from the under-

side of the old panel or panels for a distance of

approximately 2 to 3 inches back from the attaching

line.

2.
Remove the paint from the finish side, for a distance

of 2 to 3 inches on the panel adjacent to the replace-

ment panel location with lacquer solvent, or its

equivalent.

Scuff the surface on both the replacement panel and

adjacent panel for a distance of 2 to 3 inches back

from the attaching line and wipe clean.

Bevel all attaching edges at approximately 30° across

the entire thickness of the plastic so a single "V"

butt joint will be formed on the finish surface when
3.

4.
Fig. 90—Pulling Cord From Weatherstrip

the pieces are joined. If the replacement panel does

not fit closely to the break, reshape to suit.

5.
Cut two backup pieces of woven glass fiber cloth

to run the entire length of the joint or shorter

lengths of fiber cloth may be lapped over entire

length of joint, also cut wide enough to lap the

junction line on either side by two or three inches.

6. Prepare a sufficient amount of liquid plastic in an

un-waxed paper cup by mixing resin with hardener

(See Resin Repair procedure).

7.
Align replacement panel, then clamp panel in place

to form a closed "V" butt joint at the panel junction.

When panel cannot be clamped, use 3/1.6" bolts with

large washer on inner and outer of panel to hold

panels in alignment or use straps and sheet metal

screws.

Fig. 89—Installing Window Assembly

Fig. 91—Applying Sealer to Weatherstrip

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-52

and pull weatherstrip and trim from rear bow.

Section A-A shows installed position of these com-

ponents. Refer also to figure 105.

installation

1.
Find and mark center of header, #3 bow, rear bow

and leading and trailing edges of top trim. Align

these marks during installation and recheck their

alignment from time to time while installation is in

progress, especially during tacking or stapling.

2.
Assemble top trim and weatherstrip to rear bow,

referring to Section A-A and Figure 105. Note that

filler strip locks this assembly together and goes

in last. Align center marks.

3.
If new pads are required, install at this time, align-

ing with marks made when old pads were removed.

Figure 106 shows pad construction; Figure 107 shows

pad installed.

4.
Install top trim-rear bow assembly on top frame

with four screws removed at disassembly.

5.
Lock down rear bow in desired "top up" position.

Pull up stay straps and staple or tack to #3 bow

(fig. 108).

6. Pull leading edge of trim iip to header and align

center marks. Smooth out fabric and clamp, tack

or staple temporarily to header.

7.
Draw window extension up to #3 bow, aligning cen-

tering marks. Turn an ample amount of fabric under

and tack to #3 bow. Apply neoprene trim cement,

GM Part #3695016 or equivalent, to area shown in

View D of Figure 102. Follow directions on package.

8. Draw roof portion of trim over #3 bow, align marks

and tack on staple.

9. Trim off excess material and install wire-on binding

as shown in Figure 109 and View D of Figure 102.

Install binding caps.

10.
Remove temporary clamps or fastenings holding trim

to header.

11.
With header locked down, pull trim assembly up tight

and mark for final installation.

12.
Apply trim cement to header and rear side rail.

13.
Release header from windshield. Tack or staple trim

to header (fig. 103).

14.
Apply trim to rear side frame, previously cemented.

15.
Install weatherstrips which were removed at dis-

assembly and install retaining screws in header

weatherstrip.

16.
Make any adjustments necessary, following instruc-

tions listed under Folding Top—Adjustments.

FRAME AND LINKAGE

Figure 110 illustrates construction features of the

folding top frame and linkage. Various cross sections in

Figure 110 show the pivoting joints and their assembly.

If an operation is being performed which requires

removal of folding top trim, follow directions in this

section. The entire frame assembly may be removed and

replaced as a unit. Follow instructions for Folding Top

Trim and Rear Window Assembly and Top Assembly—

Removal and Installation.

The pivoting joints should be lubricated with light

machine oil once a year. Apply oil sparingly so as not

to stain top trim.
WEATHERSTRIP

Side Rail Weatherstrip

Figure 111 illustrates installation of side rail weather-

strip which acts to seal window opening. The weather-

strip is held in place by studs which are part of the

weatherstrip assembly, and by neoprene base cement

which is applied between weatherstrip and side rail

surface.

When replacing weatherstrip remove all rust, old

cement and foreign material from the surfaces to be

cemented, to assure successful bonding. Use only good

quality neoprene cement suitable for weatherstrip

application.

Header Weatherstrip

Weatherstrip assembly is retained to the header panel

by a combination of studs, sheet metal screws and special

fasteners as shown in Figure 112, along with neoprene

base weatherstrip cement.

Figure 99 shows' a cross section of weatherstrip taken

through a special fastener. To replace fastener, rotate

ninety degrees to align fastener head with slot. Follow

directions for cementing in the Side Rail Weatherstrip

instructions preceding this write up.

ADDING HARDTOP (ROOF PANEL ASSEMBLY)

An available roof panel assembly (hardtop) complete

can be added to convertible model Corvettes. The hard-

ware is included with the panel assembly.

Reworking of a plastic part (one for each side of the

roof panel) can be used as a marker for drilling of two

required holes in the folding top compartment lid* Hard-

ware is attached at four locations — two on the lid and

two (one each side) at the lock pillar area as follows:

1.
Rework two plastic retainers (#6280765) (used on

Chevrolet and Corvair door inner panels for trim

retention) as shown by Figure 113.

2.
Slide the reworked plastic retainers into the bolt re-

tainer slots on each side of the hardtop rear bow

(position plastic tip inboard).

3.
Mark the hardtop reveal molding at the approximate

location of the two plastic retainers,

4.
Mark the tips of the two plastic retainers with a

china marker pencil.

5.
Close the soft top compartment lid.

6. With aid of an ^assistant, position front of hardtop

onto header and lower onto vehicle. Do not fasten

latches at windshield header.

7.
Apply hand pressure at reveal molding marks.

8. Mark roof panel attachment hole location at each

lock pillar area (fig. 114).

9. With aid of an assistant, lift roof panel straight up

off body and set roof panel aside.

10.
Mark the drill position at the four china marks with

a center punch.

11.
Place a 2" x 4" board under the top compartment lid

to prevent drill damage to folding top material. Make

certain the compartment lid is securely locked

before drilling.

12.
Drill 1/8" pilot hole at the 4 marked locations.

CHEVROLET CHASSIS SERVICE MANUAL

STEERING
9-33

POWER STEERING

INDEX

Page

General Description
. 9-33

Maintenance
and
Adjustments
9-33

Bleeding Hydraulic System
9-33

Fluid Level
. 9-33

Adjustments
. 9-34

Power Steering Gear
. . 9-34

Pump Belt Tension
9-34
Hydraulic System Checks
9-34

Component Replacement
and
Repairs
. 9-35

Power Steering Pump.
. 9-35

Power Steering Gear
9-36

Control Valve
and
Adapter Assembly
9.35

Power Cylinder
9.37

Power Steering Hoses
9.39

GENERAL DESCRIPTION

Two types
of
power steering
are
used
for 1967.
One
is

the conventional linkage type
for
Chevy
n and
Corvette

vehicles
and the
other
is the
integral gear type
for

Chevrolet, Chevelle,
and
Camaro.
For
both types
the

hydraulic pressure
is
provided
by an
engine-driven vane-

type pump.

On
the
Chevy
n and
Corvette linkage type power steer-

ing, hydraulic pressure
is
delivered through
a
hose from

the pump
to a
valve which senses
the
requirement
for

power assistance
and
supplies
the
power cylinder
ac-

cordingly.
The
steering gear used with this power steer-

ing
is the
same basic unit used
on
manually steered

vehicles;
it is
serviced
as
outlined
in the
manual steering

part
of
this section except
for
adjustment, which
is

covered
in the
following pages.
The
steering linkage also

is serviced the same
as
manual counterparts.

The Chevrolet, Chevelle
and
Camaro integral gear type

power steering
has the
hydraulic pressure delivered

from
the
pump through two hoses
to the
steering gear.
In
the power steering gear
the
steering shaft, hydraulic

valve, worm, and rack-piston
nut are all in
line making
a

compact
and
space saving assembly.
All oil
passages
are

internal within
the
gear except
the
pressure
and
return

hoses.

The steering gear
is a
recirculating ball system
in

which steel balls
act as a
rolling thread between
the

steering worm
and
rack-piston
nut. The
rack-piston
nut

is
all one
piece
and is
geared
to the
sector
of
the piston

shaft.
The
valve
is
contained
in the
gear housing elimi-

nating
the
need
of
bolts
or
seals
to
attach
a
separate

valve housing.

The valve
is an
open-center, rotary-type three
way

valve.
The
spool
is
held
in
neutral position by means
of a

torsion
bar. The
spool
is
attached
by
means
of
the stub

shaft
to one end of the
torsion
bar
and
to the
valve body

on
the
other
end.
Twisting
of the
torsion bar allows
the

spool
to
move
in
relation
to the
valve body thereby oper-

ating
the
valve.

MAINTENANCE
AND
ADJUSTMENTS

BLEEDING HYDRAULIC SYSTEM

1.
Fill
oil
reservoir
to
proper level and
let oil
remain

undistrubed
for at
least two minutes.

2.
Start engine
and run
only
for
about
two
seconds.

3.
Add
oil if
necessary.

4.
Repeat above procedure until
oil
level remains
con-

stant after running engine.

5. Raise front
end of
vehicle
so
that wheels
are off
the

ground.

6. Increase engine speed
to
approximately
1500 rpm.

7. Turn
the
wheels
(off
ground) right
and
left, lightly

contacting
the
wheel stops.

8. Add
oil if
necessary.

9. Lower
the car and
turn wheels right and left
on the

ground.

10.
Check
oil
level and refill
as
required.

11.
If oil is
extremely foamy, allow vehicle
to
stand
a

few minutes with engine
off and
repeat above

procedure.
,

a.
Check belt tightness
and
check
for a
bent
or
loose

pulley. (Pulley should
not
wobble with engine

running.)
b.
Check
to
make sure hoses
are not
touching
any

other parts
of the car,
particularly sheet metal.

c. Check
oil
level, filling
to
proper level
if
neces-

sary, following operations
1
through
10.
This

step
and
Step
"D" are
extremely important
as

low
oil
level and/or
air in the oil are the
most

frequent causes
of
objectionable pump noise.

d. Check
the
presence
of air in the oil. If air is

present, attempt
to
bleed system
as
described
in

operations
1
through
10. If it
becomes obvious

that
the
pump will
not
bleed after
a few
trials,

proceed
as
outlined under Hydraulic System

Checks.

FLUID
LEVEL

1.
Check
oil
level
in the
reservoir
by
checking
the dip

stick when
oil is at
operating temperature.
On

Chevelle models equipped with remote reservoir,

the reservoir should
be
maintained approximately

3/4 full when
oil is at
operating temperature.

2.
Fill,
if
necessary,
to
proper level with
GM
Power

Steering Fluid
or, if
this
is not
available, automatic

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 11

CHASSIS SHEET METAL

CONTENTS OF THIS SECTION

Chevrolet and Chevelle 11-1

Chevy II . . 11.-11

Camaro 11-19

Corvette (See Section IB)

Special Tools 11-25

CHEVROLET AND CHEVELLE

INDEX

Page

General Description 11-1

Maintenance and Adjustments •. il-1

Hood Adjustment 11-1

Hinges 11-1

Bumpers 11-1

Catch Assembly and Lock 11-1

Fenders 11-4

Sheet Metal 11-4

Component Part Replacement 11-4

Battery Tray 11-4
Page

Radiator Support 11-4

Fender Assembly . . 11-4

Skirt 11-4

Trim 11-5

Hood Assembly 11-6

Lock and Catch 11-7

Trim and Insulation 11-7

Cowl Vent Grille 11-7

Rear Wheel Cover 11-7

Simulated Wood Grain Moulding . . . . 11-7

GENERAL DESCRIPTION

The new front end appearance of the 1967 Chevrolet

and Chevelle passenger cars affects the servicing and

replacement of the chassis sheet metal. Refer to Section

13 for Radiator and Grille service procedures, Section
14 for Bumpers, and Section 1A for Air Conditioning

components. Figures 1 and 2 illustrate the Chevrolet

and Chevelle sheet metal components.

MAINTENANCE AND ADJUSTMENTS

HOOD ADJUSTMENT

The alignment of the hood is controlled by the position

of the hood hinges and the height of the two bumpers lo-

cated one at each side of the radiator support. The ad-

justment at the hood lock must be made after the hinges

and bumpers are properly adjusted. To align the hood

and lock proceed as follows:

HOOD HINGE (Fig. 3)

NOTE:
The body mounted portion of the hood

hinges are slotted to provide up and down move-

ment. The hood mounted end is slotted to pro-

vide forward and rearward movement.

1.
Scribe a line around the entire hinge plate to be re-

positioned.
2.
Loosen the appropriate screws and shift the position

of the hood into correct alignment using the scribe

marks to check amount of movement. Check align-

ment by tightening screws and closing the hood.

HOOD BUMPERS

Adjust hood bumpers so that hood top surface is flush

with the fender and grille top surfaces. Refer to Fig-

ures 4 and 5 for correct sheet metal adjustment dimen-

sions.

HOOD CATCH AND LOCK

The hood catch assembly (fig. 6) mounting holes are

slotted to provide adjustment for the hood lock bolt. Ad-

just the hood lock bolt until hood engages securely when

closed and hood bumpers are slightly compressed.

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-2

Fig.
1
- Front End Sheet Metal - Chevrolet

1.
Fender

2.
Hood Hinge

3. Hood

4.
Cowl Vent Grille

5. Molding

6. Trim

7. Radiator Support

8. Shroud
9. Radiator

10.
Hood Lock

11.
Hood Catch

12.
Battery Tray

13.
Skirt

14.
Dust Shield

15.
Bracket'

16.
Brace

CHEVROLET CHASSIS SERVICE MANUAL