battery CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

GENERAL INFORMATION 0-5

Fig.
10—Delcotron Unit

Serial Number
Fig.
11—3-4 Speed Transmission Unit

Number Located on Lower Left Side of

Case Adjacent to Rear of Cover

(Saginaw)
Fig.
12-3 Speed Borg-Warner

Transmission Unit Number Located on

Boss Right Rear Comer of Extension

Fig.
13 — 4-Speed Transmission Source

Data Code is Located on Left Side of

Case at Lower Rear of Cover Flange

(Muncie)
Fig.
14—Starter Serial Number and

Production Date Stamped on Outer

Case,
Toward Rear
Fig.
15—Powerglide Transmission Unit

Number located on Right Rear Vertical

Surface of Oil Pan

16—The Turbo Hydra-Matic Transmission Serial Number

is Located on the Light Blue Plate

Location on the Right Side of the Transmission

tumbler, single bitted type having four tumblers. To

protect owners, automobile lock manufacturers stamp

the lock numbers on the lock core, shaft, etc., where they

will not show until lock is removed.

In addition, when a lock cylinder requires replacement

the lock code number may be obtained either from the

key, if available, or from old lock cylinder which is being

replaced.
Fig.
17—Battery Code Number Located on Cell

Cover Segment, Top of Battery

TUMBLERS

5 4 3 2 1

jjwvvvvvjl

SPRING RETAINER

Fig.
18-Side Bar Lock

CHEVROLET CHASSIS SERVICE MANUAL

GENERAL INFORMATION 0-7

a vise using leather or wood on each side to prevent

damage to the cylinder,

7. Stake the retainer securely in place by staking the

cylinder metal over both edges of the retainer ends

using a suitable staking tool at right angles to the

top of the retainer and from the cast metal of the

cylinder over the retainer at each corner.

PUSHING, TOWING AND LIFTING

Pushing

NOTE:
Towing car to start is not recommended

due to the possibility of the disabled car ac-

celerating into tow car.

AUTOMATIC TRANSMISSION

Do not attempt to start the engine by pushing the car.

Should the battery become discharged, it will be neces-

sary to use an auxiliary battery with jumper cables to

start the engine.

CAUTION: To prevent damage to electrical

system, never connect booster batteries in ex-
cess of 12 volts and connect positive to positive

and negative to negative.

Manual Transmission

When a push start is necessary turn off all electrical

loads such as heater, radio, and if possible, lights, turn

on the key, depress the clutch, and place the shift lever

in high gear. Release the clutch when your speed reaches

10 to 15 miles per hour.

TOWING

The car may be towed safely on its rear wheels with

the (selector lever in "N" (Neutral) position at speeds

of 35 miles per hour or less under most conditions.

However, the drive shaft must be disconnected or the

car towed on its front wheels if 1) Tow speeds in excess

of 35 MPH are necessary, 2) Car must be towed for ex-

tended distances (over 50 miles) or, 3) Transmission is

not operating properly. If car is towed on its front

wheels, the steering wheel should be secured to maintain

a straight ahead position.

DRIVE ON HOIST

BUMPER JACK LIFTING AT FRAME ATTACHMENT ONLY

FLOOR JACK OR HOIST LIFT

Fig.
21-Vehicle Lifting Pointe-Chevroiet

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-13

LUBRICATION

INDEX

Page

Engine Crankcase Oil . 0-13

Crankcase Capacities. . 0-13

Lubrication . ,
•
o-13

SAE Viscosity Oils 0-13

Types of Oils 0-14

Maintaining Oil Level 0-14

Oil and Filter Change Intervals 0-14

Oil.
. . ...:.. 0-14

Filter o-14

Crankcase Dilution . 0-14

Automatic Control Devices to Minimize

Crankcase Dilution 0-14

Crankcase Breather Cap 0-14

Crankcase Ventilation System 0-15

Valve Type 0-15

Fuel Filter 0-15

Air Cleaner . 0-15

Polyurethane Type 0-15

Oil Wetted Paper Element Type 0-15

Battery Terminal Washers 0-15
Page

Distributor 0-15

Rear Axle and 3-Speed and Overdrive

4-Speed Transmission 0-15

Recommended Lubricants 0-15

Multi-Purpose Gear Lubricants 0-15

Lubricant Additions 0-15

Lubricant Changes 0-15

Powerglide Transmission 0-15

Turbo Hydra-Matic 0-16

Front Wheel Bearings 0-16

Manual Steering Gear . . . . 0-16

Power Steering 0-16

Air Conditioning 0-16

Brake Master Cylinder. 0-16

Parking Brake 0-16

Clutch Cross-Shaft , 0-16

Chassis Lubrication 0-16

Lubrication Diagrams . . 0-19

Body Lubrication (Chevrolet, Chevelle, Chevy n, Camaro). 0-20

Body Lubrication Points (Corvette) . 0-21

The selection of the proper lubricant and its correct

application at regular intervals does much to increase the

life and operation of all moving parts of the vehicle.

Consequently, it is important that the correct grade of

oil or grease, as noted in the following pages, be used.

ENGINE CRANKCASE OIL

Crankcase Capacity

4 Cylinder 4 qt.

6 Cylinder 4 qt.

8 Cylinder (283) 4 qt.

8 Cylinder (327) 4 qt.

8 Cylinder (350) 4 qt.

8 Cylinder (396) 4 qt.

8 Cylinder (427) Chevrolet 4 qt.

8 Cylinder (427) Corvette 5 qt.

For 4 Cyl. Add .5 qt. with filter change;

1 qt. for 6 and 8 Cyl. engines.

Lubrication

Crankcase oil should be selected to give the best per-

formance under the climatic and driving conditions in the

territory in which the vehicle is driven.

During warm or hot weather, an oil which will provide

adequate lubrication under high operating temperatures

is required.

During the colder months of the year* an oil which will

permit easy starting at the lowest atmospheric tempera-

ture likely to be encountered, should be used.

When the crankcase is drained and refilled, the crank-

case oil should be selected, not on the basis of the exist-

ing temperature at the time of the change, but on the

lowest temperature anticipated for the period during

which the oil is to be used.

Unless the crankcase oil is selected on the basis of

viscosity or fluidity of the anticipated temperature, dif-

ficulty in starting will be experienced at each sudden

drop in temperature.
SAE Viscosity Oils

SAE Viscosity Numbers indicate only the viscosity or

body of the oil, that is, whether an oil is a light or a

heavy body oil, and do not consider or include other

properties or quality factors.

The lower SAE Viscosity Numbers, such as SAE 5W

and SAE 10W which represent the light body oils, are

recommended for use during cold weather to provide

easy starting and instant lubrication. The higher SAE

Viscosity Numbers such as SAE 20 and SAE 20W, which

represents heavier body oils, are recommended for use

during warm or hot weather to provide improved oil

economy and adequate lubrication under high operating

temperatures.

Oils are available which are designed to combine the

easy starting characteristics of the lower SAE Viscosity

Number with the warm weather operating characteristics

of the higher SAE Viscosity Number. These are termed

"multi-viscosity oils," SAE 5-10W, SAE 5W-20, SAE

10W-20W, and SAE 10W-30.

The following chart will serve as a guide for the

selection of the correct SAE Viscosity Number for use

under different atmospheric temperature ranges, and

suggests the appropriate SAE Viscosity Numbers when

multi-viscosity oils are used.

Lowest Anticipated

Temperature

During Time

Oil Will Be

in Crankcase

32°F.

0°F.

Below 0°F.
Recommended

SAE Viscosity

Oils

SAE 20 or 20W

SAE 10W

SAE 5W
Recommended

SAE

Multi-

Viscosity

Oils

SAE 10W-30 .

SAE 10W-30

SAE 5W-20

SAE 30 or 10W-30 is recommended when most of the

driving is at high speeds and/or at temperatures above

90
°F.

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-15

CRANKCASE VENTILATION VALVE

VALVE TYPE

NOTE: Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often. Every 12,000 miles

or 12 months the valve should be replaced.

Connecting hoses, fittings, flame arrestor and

crankcase breather cap (where used) should be

cleaned. At every oil change the system should

be tested for proper function and serviced, if

necessary.

FUEL FILTER

Replace filter element located in carburetor inlet if

flooding occurs, if engine surges during constant speed

operation (pulsating effect) or if poor performance is

experienced during acceleration or at higher speeds.

AIR CLEANER

NOTE: Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often.

POLYURETHANE TYPE-

Every 12,000 miles clean element in solvent, squeeze

out solvent, then soak in engine oil and squeeze out

excess.

OIL WETTED PAPER ELEMENT TYPE-

First 12,000 miles inspect or test element; if satis-

factory, re-use element but recheck every 6,000 miles

until replaced. Element must not be washed, oiled,

tapped or cleaned with an air hose.

BATTERY TERMINAL WASHERS

Battery terminals have felt washers between top of

case and cable connections to minimize corrosive action

of battery acid. These felt washers should be saturated

with engine oil every 6,000 miles.

DISTRIBUTOR

4 and 6-Cylinder Engine—Remove distributor cap and

rotate lubricator 1/2 turn at 12,000 mile intervals. Re-

place at 24,000 mile intervals.

8-Cylinder Engine—Change cam lubricator end for end

at 12,000 mile intervals. Replace at 24,000 mile

intervals.

REAR AXLE AND 3-SPEED AND

OVERDRIVE, 4-SPEED TRANSMISSIONS

The passenger car operates under the most severe

lubrication conditions at high speed and requires a hypoid

lubricant which will meet this condition.

Recommended Lubricants

Standard Rear Axles—SAE 90 "Multi-Purpose" gear

lubricant.

Positraction Rear Axles—Use special Positraction

lubricant.
CAUTION: Straight Mineral Oil gear lubricants

must not be used in hypoid rear axles.

Transmissions—SAE 90 "Multi-Purpose" gear

lubricant.

The SAE 90 viscosity grade is recommended for year

round use. However, when extremely low temperatures

are encountered for protracted periods during the winter

months, the SAE 80 viscosity grade may be used.

"Multi-Purpose" Gear Lubricants

Gear lubricants that will satisfactorily lubricate hypoid

rear axles have been developed and are commonly re-

ferred to as ' 'Multi-Purpose" gear lubricants meeting

U.S.
Army Ord. Spec. MIL-L-2105B.

These lubricants can also be satisfactorily used in

manual transmissions.

CAUTION: With Positraction rear axles use

special Positraction lubricant.

"Multi-Purpose" gear lubricants must be manufac-

tured under carefully controlled conditions and the

lubricant manufacturer must be responsible for the

satisfactory performance of his product. His reputation

is the best indication of quality.

Lubricant Additions

The lubricant level in the axle and transmission hous-

ings should be checked periodically. (Every 6,000 miles.)

It is recommended that any additions required to bring

up the lubricant level be made using the same type lubri-

cant already in the housing.

When checking lubricant level in transmission or rear

axle the unit being cheeked should be at operating

temperature. With unit at operating temperature the

lubricant should be level with bottom of the filler plug

hole.
If the lubricant level is checked with the unit cold

the lubricant level should be 1/2 inch below the filler

plug hole.

Lubricant Changes

The rear axle lubricant does not require changing for

the life of the vehicle. If additions are needed, or when

refilling the axle after service procedures, use lubricants

described above.

POWERGLIDE TRANSMISSION

NOTE: Every 12,000 miles, it is recommended

that the Powerglide low band be adjusted as

specified in Section 7 of this manual.

Every 6,000 miles--Check fluid level on dipstick with

engine idling, selector lever in neutral position, parking

brake set and transmission at operating temperature. If

fluid level is below full mark on dip stick, adding a small

amount of Automatic Transmission Fluid, General Motors

Automatic Transmission Fluid (Part Numbers 1050568-

69,
70) is recommended. If this fluid is not obtainable,

use Automatic Transmission Fluid Type 'A' bearing the

mark AQ-ATF followed by a number and the suffix letter

'A'.
Recheck fluid level on dip stick and again add a

small amount of fluid if needed to bring level to full

mark. DO NOT OVERFILL.

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-17

LUBRICATE EVERY 6,000 MILES

LUBRICATE EVERY 12,000 MILES

LUBRICATE EVERY 36,000 MILES

Refill Positraction Rear Axle with

Special Lubricant Only.
GL—Multi-purpose
or
Universal Gear Lubricant4

WB-Wheel Bearing Lubricant

(Whenever Brakes are serviced)

CL—Chassis Lubricant

EO-EngineOil
AT-Automatic Transmission Fluid {Type
A)

BF-Brake Fluid

Fig.
32—Lubrication Diagram—Chevrolet

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air Cleaner

5. Crankcase Breather Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master Cylinder

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-18

12

LUBRICATE EVERY 6000 MILES GL -Multi-purpose Gear Lubricant*

WB—Wheel Bearing Lubricant

LUBRICATE EVERY 12000 MILES (Whenever Brakes are serviced)

CL —Chassis Lubricant

LUBRICATE EVERY 36000 MILES E°-En9ine°il

"Refill Positraction Rear Axle with Special Positraction Rear Axle

Lubricant Only.
AT —Automatic Transmission Fluid (Type A)

SL —Steering Gear Lubricant

BF -Hydraulic Brake Fluid

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
Fig.
33—Lubrication Diagram—Chevelle

4.
Air Cleaner

5. Crankcase Breather Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master CylincU

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION
0-19

.
3-SPEED
4-SPEED

7 OVER DRIVE

10 9 5 1 6 2 '
AUTOMATIC

3 12 11

LUBRICATE EVERY 6,000 MILES GL-Gear Lubricant*

WB-Wheel Bearing Lubricant

(Wh Bk
AT-Automdtic Transmission Fluid

^ WB-Wheel Bearing Lubricant (Type A)

-TV
LUBRICATE
EVERY 12,000 MILES (Whenever Brakes are serviced)

' CL—Chassis Lubricant

• LUBRICATE EVERY 36,000 MILES EO_Engine Oil
BF
-Brake Fluid

•Refill Positt

Special Lubricant Only.
Axl«
with

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
Fig.
34—Lubrication Diagram—Chevy I!

4. Air Cleaner

5. Crankcase Breather. Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9.
Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master Cylinder

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-20

3-SPEED

4—SPEED

AUTOMATIC

LUBRICATE EVERY 6000 MILES

LUBRICATE EVERY 12000 MILES

LUBRICATE EVERY 36000 MILES

*
Refill
positraction rear axle with

special lubricant only.
GL -GEAR LUBRICANT*

WB-WHEEL BEARING LUBRICANT

(WHENEVER BRAKES
ARE
SERVICED)

CL -CHASSIS LUBRICANT

CO-ENGINE
Oil;
AT -AUTOMATIC TRANSMISSION

FLUID (TYPE
A)

BF -BRAKE FLUID

Fig.
35—Lubricafion Diagram—Camaro

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air Cleaner

5. Crankcase Breathe Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery,

11.
Parking Brake

12.
Brake Master Cylinder

BODY LUBRICATION

See Body Service Manual
for
Body Lubrication,

cept Corvette)
(Ex-

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION
0-21

6

3-SPEED

4-SPEED

AUTOMATIC

10

LUBRICATE EVERY 6,000 MILES GL -Multi-purpose
or
Universal Gear Lubrincant*

-(V LUBRICATE EVERY 12,000 MILES WB-Wheel Bearing Lubricant

V/^ (Whenever Brakes
are
serviced)
AT —Automatic Transmission Fluid (Type)

BF -Brake Fluid

a
LUBRICATE EVERY 36,000 MILES

* Refill Positraction Rear Axle with

Special Lubricant Only.
CL -Chassis Lubricant

EO—Engine
Oil

Fig.
36—Lubrication Diagram—Corvette

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air
Cleaner

5. Front Wheel

Bearings
6. Transmission

7. Rear Axle

8.
Oil
Filter
9. Battery

10.
Parking Brake

11.
Brake Master Cylinder

BODY LUBRICATION POINTS (CORVETTE)

Lubricate the following items when possible.

Hood Latch Mechanism and Hinges --Apply light engine oil

to pivot points. Don't oil lock pins or catch plates.

i

Rear Compartment Lid Release and Hinges --Apply light

engine
oil.

Side Door Hinge Pins—Apply light engine oil.
Door Lock Rotor and Striker Plate—Apply light engine oil or

stainless stick lubricant.

Lock Cylinders—Lubricate with powdered graphite.

Window Regulators and Controls and Door Lock Remote

Link —Apply light engine
oil.

Gas Tank Filler Cap Hinge—Apply light engine oil.

Weatherstrips and Rubber Bumpers —Coat lightly with
a

rubber lubricant.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-3

linkage of this lever which will provide partial airflow

only to the defroster duct and which should be used for,

all normal defogging operations.

CORVETTE

Heater components are attached to the dash panel on

the right side of the vehicle with the air inlet assembly

on the engine side and the heater and air distributor

assemblies beneath the instrument panel within the pas-

senger compartment.

The heater operates on outside air only with the blower

receiving its air flow from the cowl vent plenum

chamber.

No water valve is utilized in the system. Therefore,

water flows through the heater core constantly while

the engine is running, keeping the core at maximum

temperature at all times.

Airflow through the system is shown in Figure 1.

Controls

Two knobs control all heater operations:

The FAN-TEMP knob is rotated to turn the blower

on and off and control blower speed and is pulled out

as desired to regulate heater temperature.

The AIR-DEF knob is the air on-and-off control as

well as the defroster control.

Temperature Damper: Door

At the heart of the heater operation is the temperature

damper door. Air from the blower follows parallel paths

through the distributor duct, with one path passing

through the heater core and the other path bypassing the

core.

The temperature damper door is placed in the duct

so that, when closed, the path of the heated air leaving

the heater core is blocked while the ambient air path

remains open. Positive closing of this door when no

heat is being called for is assured by a cam assembly

at the door operating lever. As the FAN-TEMP knob

is pulled out, the damper door is opened accordingly,

allowing varying proportions of heated air to mix with

the unheated airflow, thus providing heater outlet tem-

perature control. With the knob pulled fully out the
Fig.
4—Heater Controls (Corvette)

ambient air path is blocked and all airflow passes

through the heater core. Final heater output temperature

is dependent upon the proportion of heated and ambient

air blended together according* to the setting of the

temperature damper door.

Air and Defrost Damper Doors

Beyond the temperature damper door are the air door

and the defroster door, both operated through a single

bowden cable by the AIR-DEF knob. The first half of the

travel of this knob opens the AIR door allowing the

airflow to pass into the interior of the car through the

floor distributor openings. Pulling the AIR-DEF knob

fully out causes the defroster door to open, diverting

this airflow to the defroster ducts for defogging, de-

frosting or deicing operations.

NOTE: Since this knob is the air on-or-off

control, it should be pulled at least halfway out

before turning on the blower.

Fan Control

Rotate the FAN-TEMP knob to operate the three-

speed blower, increasing the velocity of the air through

the heater. The fully counter-clockwise position of the

knob is the off position. Turn clockwise to the desired

blower speed; fully clockwise for high blower speed.

COMPONENT REPLACEMENT AND REPAIR

CHEVROLET, CHEVELLE, AND CAMARO

Blower Assembly

Removal

1.
Disconnect battery ground cable.

2.
Unclip heater hoses from fender skirt.

3.
(Chevrolet and Camaro) Remove right front fender

and skirt assembly. (See Section 11 of the Service

Shop Manual)

(Chevelle) Move the vehicle front wheels to the

extreme right turn position. Remove all right front

fender retaining bolts. Allow the skirt to drop and

rest on top of the tire. To gain maximum clearance

for access to the blower motor attaching screws, a

block of wood may be wedged between the fender

lower flange and the top of the fender skirt. Position

the wood block so that the rear portion of the skirt

will be forced down and inboard. (See Figure 7.)
4.
Disconnect the blower motor wire at the motor

flange.

5.
Remove the motor to case mounting screws and re-

move motor. Pry the flange gently if the sealer acts

as an adhesive.

6. Remove the blower wheel retaining nut and separate

blower and motor.

Installation

1.
Assemble the blower wheel to the motor with the

open end of the blower away from the motor.

2.
Place the assembly into the case and replace the

mounting screws. Connect the blower motor wire to

the motor.

3.
(Chevrolet and Camaro) Replace the fender and

skirt assembly.

(Chevelle) Replace the fender skirt.

4.
Clip the heater hoses to the fender skirt and connect

the battery ground cable.

CHEVROLET CHASSIS SERVICE MANUAL