brake CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

GENERAL INFORMATION
0-9

Fig.
25—Attachment
of
Towing Chain Hooks
to
Axle Tube

Fig.
24—Towing Sling Attachment—Front

Rear

Connect standard chain hooks around the axle tube from

the underneath side between the axle rear spring pad and

the brake flange plate (fig. 25). It is mandatory that the

chain hook be positioned as stated above so that the brake

lines are not damaged.

The lower lifting bar should be positioned in below the

vehicle so that the rubber straps protect the rear valance

panel. With the lower bar in this position, it is necessary

that the bar be spaced down a minimum of
1
5/8" to pre-

vent damage to the fuel tank. This can be accomplished

by placing 6.0" section of 2x4' wood blocks below the

rear section of each rear spring (fig. 26).

To facilitate towing without a helper it will be neces-

sary to attach the
2x4*
s to the rear spring by a strap or

tape.
See Figure 27.

Also it will be necessary to lock the steering wheel in

the straight ahead position prior to actually moving the

vehicle.
Fig.
26—Towing SJing Attachment—Rear

REAR SPRING

EYE

WOOD

BLOCK

Fig.
27—Strapping Wood Block
to
Rear Spring

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-13

LUBRICATION

INDEX

Page

Engine Crankcase Oil . 0-13

Crankcase Capacities. . 0-13

Lubrication . ,
•
o-13

SAE Viscosity Oils 0-13

Types of Oils 0-14

Maintaining Oil Level 0-14

Oil and Filter Change Intervals 0-14

Oil.
. . ...:.. 0-14

Filter o-14

Crankcase Dilution . 0-14

Automatic Control Devices to Minimize

Crankcase Dilution 0-14

Crankcase Breather Cap 0-14

Crankcase Ventilation System 0-15

Valve Type 0-15

Fuel Filter 0-15

Air Cleaner . 0-15

Polyurethane Type 0-15

Oil Wetted Paper Element Type 0-15

Battery Terminal Washers 0-15
Page

Distributor 0-15

Rear Axle and 3-Speed and Overdrive

4-Speed Transmission 0-15

Recommended Lubricants 0-15

Multi-Purpose Gear Lubricants 0-15

Lubricant Additions 0-15

Lubricant Changes 0-15

Powerglide Transmission 0-15

Turbo Hydra-Matic 0-16

Front Wheel Bearings 0-16

Manual Steering Gear . . . . 0-16

Power Steering 0-16

Air Conditioning 0-16

Brake Master Cylinder. 0-16

Parking Brake 0-16

Clutch Cross-Shaft , 0-16

Chassis Lubrication 0-16

Lubrication Diagrams . . 0-19

Body Lubrication (Chevrolet, Chevelle, Chevy n, Camaro). 0-20

Body Lubrication Points (Corvette) . 0-21

The selection of the proper lubricant and its correct

application at regular intervals does much to increase the

life and operation of all moving parts of the vehicle.

Consequently, it is important that the correct grade of

oil or grease, as noted in the following pages, be used.

ENGINE CRANKCASE OIL

Crankcase Capacity

4 Cylinder 4 qt.

6 Cylinder 4 qt.

8 Cylinder (283) 4 qt.

8 Cylinder (327) 4 qt.

8 Cylinder (350) 4 qt.

8 Cylinder (396) 4 qt.

8 Cylinder (427) Chevrolet 4 qt.

8 Cylinder (427) Corvette 5 qt.

For 4 Cyl. Add .5 qt. with filter change;

1 qt. for 6 and 8 Cyl. engines.

Lubrication

Crankcase oil should be selected to give the best per-

formance under the climatic and driving conditions in the

territory in which the vehicle is driven.

During warm or hot weather, an oil which will provide

adequate lubrication under high operating temperatures

is required.

During the colder months of the year* an oil which will

permit easy starting at the lowest atmospheric tempera-

ture likely to be encountered, should be used.

When the crankcase is drained and refilled, the crank-

case oil should be selected, not on the basis of the exist-

ing temperature at the time of the change, but on the

lowest temperature anticipated for the period during

which the oil is to be used.

Unless the crankcase oil is selected on the basis of

viscosity or fluidity of the anticipated temperature, dif-

ficulty in starting will be experienced at each sudden

drop in temperature.
SAE Viscosity Oils

SAE Viscosity Numbers indicate only the viscosity or

body of the oil, that is, whether an oil is a light or a

heavy body oil, and do not consider or include other

properties or quality factors.

The lower SAE Viscosity Numbers, such as SAE 5W

and SAE 10W which represent the light body oils, are

recommended for use during cold weather to provide

easy starting and instant lubrication. The higher SAE

Viscosity Numbers such as SAE 20 and SAE 20W, which

represents heavier body oils, are recommended for use

during warm or hot weather to provide improved oil

economy and adequate lubrication under high operating

temperatures.

Oils are available which are designed to combine the

easy starting characteristics of the lower SAE Viscosity

Number with the warm weather operating characteristics

of the higher SAE Viscosity Number. These are termed

"multi-viscosity oils," SAE 5-10W, SAE 5W-20, SAE

10W-20W, and SAE 10W-30.

The following chart will serve as a guide for the

selection of the correct SAE Viscosity Number for use

under different atmospheric temperature ranges, and

suggests the appropriate SAE Viscosity Numbers when

multi-viscosity oils are used.

Lowest Anticipated

Temperature

During Time

Oil Will Be

in Crankcase

32°F.

0°F.

Below 0°F.
Recommended

SAE Viscosity

Oils

SAE 20 or 20W

SAE 10W

SAE 5W
Recommended

SAE

Multi-

Viscosity

Oils

SAE 10W-30 .

SAE 10W-30

SAE 5W-20

SAE 30 or 10W-30 is recommended when most of the

driving is at high speeds and/or at temperatures above

90
°F.

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-15

CRANKCASE VENTILATION VALVE

VALVE TYPE

NOTE: Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often. Every 12,000 miles

or 12 months the valve should be replaced.

Connecting hoses, fittings, flame arrestor and

crankcase breather cap (where used) should be

cleaned. At every oil change the system should

be tested for proper function and serviced, if

necessary.

FUEL FILTER

Replace filter element located in carburetor inlet if

flooding occurs, if engine surges during constant speed

operation (pulsating effect) or if poor performance is

experienced during acceleration or at higher speeds.

AIR CLEANER

NOTE: Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often.

POLYURETHANE TYPE-

Every 12,000 miles clean element in solvent, squeeze

out solvent, then soak in engine oil and squeeze out

excess.

OIL WETTED PAPER ELEMENT TYPE-

First 12,000 miles inspect or test element; if satis-

factory, re-use element but recheck every 6,000 miles

until replaced. Element must not be washed, oiled,

tapped or cleaned with an air hose.

BATTERY TERMINAL WASHERS

Battery terminals have felt washers between top of

case and cable connections to minimize corrosive action

of battery acid. These felt washers should be saturated

with engine oil every 6,000 miles.

DISTRIBUTOR

4 and 6-Cylinder Engine—Remove distributor cap and

rotate lubricator 1/2 turn at 12,000 mile intervals. Re-

place at 24,000 mile intervals.

8-Cylinder Engine—Change cam lubricator end for end

at 12,000 mile intervals. Replace at 24,000 mile

intervals.

REAR AXLE AND 3-SPEED AND

OVERDRIVE, 4-SPEED TRANSMISSIONS

The passenger car operates under the most severe

lubrication conditions at high speed and requires a hypoid

lubricant which will meet this condition.

Recommended Lubricants

Standard Rear Axles—SAE 90 "Multi-Purpose" gear

lubricant.

Positraction Rear Axles—Use special Positraction

lubricant.
CAUTION: Straight Mineral Oil gear lubricants

must not be used in hypoid rear axles.

Transmissions—SAE 90 "Multi-Purpose" gear

lubricant.

The SAE 90 viscosity grade is recommended for year

round use. However, when extremely low temperatures

are encountered for protracted periods during the winter

months, the SAE 80 viscosity grade may be used.

"Multi-Purpose" Gear Lubricants

Gear lubricants that will satisfactorily lubricate hypoid

rear axles have been developed and are commonly re-

ferred to as ' 'Multi-Purpose" gear lubricants meeting

U.S.
Army Ord. Spec. MIL-L-2105B.

These lubricants can also be satisfactorily used in

manual transmissions.

CAUTION: With Positraction rear axles use

special Positraction lubricant.

"Multi-Purpose" gear lubricants must be manufac-

tured under carefully controlled conditions and the

lubricant manufacturer must be responsible for the

satisfactory performance of his product. His reputation

is the best indication of quality.

Lubricant Additions

The lubricant level in the axle and transmission hous-

ings should be checked periodically. (Every 6,000 miles.)

It is recommended that any additions required to bring

up the lubricant level be made using the same type lubri-

cant already in the housing.

When checking lubricant level in transmission or rear

axle the unit being cheeked should be at operating

temperature. With unit at operating temperature the

lubricant should be level with bottom of the filler plug

hole.
If the lubricant level is checked with the unit cold

the lubricant level should be 1/2 inch below the filler

plug hole.

Lubricant Changes

The rear axle lubricant does not require changing for

the life of the vehicle. If additions are needed, or when

refilling the axle after service procedures, use lubricants

described above.

POWERGLIDE TRANSMISSION

NOTE: Every 12,000 miles, it is recommended

that the Powerglide low band be adjusted as

specified in Section 7 of this manual.

Every 6,000 miles--Check fluid level on dipstick with

engine idling, selector lever in neutral position, parking

brake set and transmission at operating temperature. If

fluid level is below full mark on dip stick, adding a small

amount of Automatic Transmission Fluid, General Motors

Automatic Transmission Fluid (Part Numbers 1050568-

69,
70) is recommended. If this fluid is not obtainable,

use Automatic Transmission Fluid Type 'A' bearing the

mark AQ-ATF followed by a number and the suffix letter

'A'.
Recheck fluid level on dip stick and again add a

small amount of fluid if needed to bring level to full

mark. DO NOT OVERFILL.

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-16

Every 12,000 miles (more frequently*, depending on

severity of service, if vehicle is used to pull trailers,

carry full loads during high ambient temperatures,

operate in mountainous terrain or operate under other

severe conditions--Remove fluid from the transmission

sump and add one and a half quarts of fresh fluid for

Camaro and Chevy II and two quarts for Chevrolet,

Chevelle, and Corvette. Operate transmission through all

ranges and check fluid level as described above.

•Except if vehicle is equipped with transmission pro-

vided in heavy duty service options. If so equipped,

drain converter and pump every 12,000 miles and add

approximately seven and a half quarts of fresh fluid

for Chevy II and nine quarts for Chevrolet and Chevelle.

TURBO HYDRA-MATIC

Lubrication. recommendations for the Turbo Hydra-

Matic are the same as outlined for the Powerglide

transmission except for fluid capacity and filter change

listed below.

After checking transmission fluid level it is important

that the dip stick be pushed all the way into the fill tube.

Every 12,000 miles — after removing fluid from the

transmission sump, approximately 7 1/2 pints of fresh

fluid will be required to return level to proper mark on

the dip stick.

Every 24,000 miles, or at every other fluid change--

the transmission sump strainer should be replaced.

FRONT WHEEL BEARINGS

It is necessary to remove the wheel and hub assembly

to lubricate the bearings. The bearing assemblies should

be cleaned before repacking with lubricant. Do not pack

the hub between the inner and outer bearing assemblies

or the hub caps, as this excessive lubrication results in

the lubricant working out into the brake drums and

linings.

Front wheels of all passenger car models are equipped

with tapered roller bearings and should be packed with a

high melting point water resistant front wheel bearing

lubricant whenever wheel and hub are removed.

CAUTION: "Long fibre" or "viscous" type

lubricant should not be used. Do not mix wheel

bearing lubricants. Be sure to thoroughly clean

bearings and hubs of all old lubricant before

repacking.

The proper adjustment of front wheel bearings is one

of the important service operations- that has a definite

bearing on safety. A car with improperly adjusted front

wheel bearings lacks steering stability, has a tendency to

wander or shimmy and may have increased tire wear.
The adjustment of these bearings is very critical. The

procedure is covered in Section 3 of this manual under

Front Wheel Bearings—Adjust,

MANUAL STEERING GEAR

Check lubricant level every 36,000 miles. If required,

add EP Chassis Lubricant.

POWER STEERING

On models equipped with power steering gear, check

fluid at operating temperature in pump reservoir. Add

GM Power Steering Fluid, or, if this is not available, use

Automatic Transmission Fluid "Type A" bearing the

mark AQ-ATF followed by a number and the suffix letter

'A'
to bring level to full mark on dip stick.

AIR CONDITIONING

After the first 6,000 miles, check all hose clamp

connections for proper tightness.

Every 6,000 miles check sight glass under the hood,

after the system has been in operation for several

minutes. Sight glass should be clear but may, during

milder weather, show traces of bubbles. Foam or dirt

indicate a leak which should be repaired immediately.

BRAKE MASTER CYLINDER

Check level every 6,000 miles and maintain 1/4" below

lowest edge of each filler opening with GM Hydraulic

Brake Fluid Supreme No. 11.

PARKING BRAKE

Every 6,000 miles, apply water resistant lube to park-

ing brake cable, cable guides and at all operating links

and levers.

CLUTCH CROSS-SHAFT

Periodic lubrication of the clutch cross shaft is not

required. At 36,000 miles or sooner, if necessary;

remove plug, install lube fitting and apply CHASSIS

LUBRICANT.

CHASSIS LUBRICATION

For chassis lubrication, consult the lubrication chart.

It shows the points to be lubricated and how often the

lubricant should be applied.

The term "chassis lubricant" as used in this manual,

describes a water resistant EP chassis grease designed

for application by commercial pressure gun equipment.

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-17

LUBRICATE EVERY 6,000 MILES

LUBRICATE EVERY 12,000 MILES

LUBRICATE EVERY 36,000 MILES

Refill Positraction Rear Axle with

Special Lubricant Only.
GL—Multi-purpose
or
Universal Gear Lubricant4

WB-Wheel Bearing Lubricant

(Whenever Brakes are serviced)

CL—Chassis Lubricant

EO-EngineOil
AT-Automatic Transmission Fluid {Type
A)

BF-Brake Fluid

Fig.
32—Lubrication Diagram—Chevrolet

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air Cleaner

5. Crankcase Breather Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master Cylinder

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-18

12

LUBRICATE EVERY 6000 MILES GL -Multi-purpose Gear Lubricant*

WB—Wheel Bearing Lubricant

LUBRICATE EVERY 12000 MILES (Whenever Brakes are serviced)

CL —Chassis Lubricant

LUBRICATE EVERY 36000 MILES E°-En9ine°il

"Refill Positraction Rear Axle with Special Positraction Rear Axle

Lubricant Only.
AT —Automatic Transmission Fluid (Type A)

SL —Steering Gear Lubricant

BF -Hydraulic Brake Fluid

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
Fig.
33—Lubrication Diagram—Chevelle

4.
Air Cleaner

5. Crankcase Breather Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master CylincU

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION
0-19

.
3-SPEED
4-SPEED

7 OVER DRIVE

10 9 5 1 6 2 '
AUTOMATIC

3 12 11

LUBRICATE EVERY 6,000 MILES GL-Gear Lubricant*

WB-Wheel Bearing Lubricant

(Wh Bk
AT-Automdtic Transmission Fluid

^ WB-Wheel Bearing Lubricant (Type A)

-TV
LUBRICATE
EVERY 12,000 MILES (Whenever Brakes are serviced)

' CL—Chassis Lubricant

• LUBRICATE EVERY 36,000 MILES EO_Engine Oil
BF
-Brake Fluid

•Refill Positt

Special Lubricant Only.
Axl«
with

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
Fig.
34—Lubrication Diagram—Chevy I!

4. Air Cleaner

5. Crankcase Breather. Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9.
Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master Cylinder

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-20

3-SPEED

4—SPEED

AUTOMATIC

LUBRICATE EVERY 6000 MILES

LUBRICATE EVERY 12000 MILES

LUBRICATE EVERY 36000 MILES

*
Refill
positraction rear axle with

special lubricant only.
GL -GEAR LUBRICANT*

WB-WHEEL BEARING LUBRICANT

(WHENEVER BRAKES
ARE
SERVICED)

CL -CHASSIS LUBRICANT

CO-ENGINE
Oil;
AT -AUTOMATIC TRANSMISSION

FLUID (TYPE
A)

BF -BRAKE FLUID

Fig.
35—Lubricafion Diagram—Camaro

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air Cleaner

5. Crankcase Breathe Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery,

11.
Parking Brake

12.
Brake Master Cylinder

BODY LUBRICATION

See Body Service Manual
for
Body Lubrication,

cept Corvette)
(Ex-

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION
0-21

6

3-SPEED

4-SPEED

AUTOMATIC

10

LUBRICATE EVERY 6,000 MILES GL -Multi-purpose
or
Universal Gear Lubrincant*

-(V LUBRICATE EVERY 12,000 MILES WB-Wheel Bearing Lubricant

V/^ (Whenever Brakes
are
serviced)
AT —Automatic Transmission Fluid (Type)

BF -Brake Fluid

a
LUBRICATE EVERY 36,000 MILES

* Refill Positraction Rear Axle with

Special Lubricant Only.
CL -Chassis Lubricant

EO—Engine
Oil

Fig.
36—Lubrication Diagram—Corvette

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air
Cleaner

5. Front Wheel

Bearings
6. Transmission

7. Rear Axle

8.
Oil
Filter
9. Battery

10.
Parking Brake

11.
Brake Master Cylinder

BODY LUBRICATION POINTS (CORVETTE)

Lubricate the following items when possible.

Hood Latch Mechanism and Hinges --Apply light engine oil

to pivot points. Don't oil lock pins or catch plates.

i

Rear Compartment Lid Release and Hinges --Apply light

engine
oil.

Side Door Hinge Pins—Apply light engine oil.
Door Lock Rotor and Striker Plate—Apply light engine oil or

stainless stick lubricant.

Lock Cylinders—Lubricate with powdered graphite.

Window Regulators and Controls and Door Lock Remote

Link —Apply light engine
oil.

Gas Tank Filler Cap Hinge—Apply light engine oil.

Weatherstrips and Rubber Bumpers —Coat lightly with
a

rubber lubricant.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-65

Fig.
92—Chevrolet Four-Season Ducts

Installation

Reverse

assembly.
the removal procedure to reinstall the duct

Left Outlet Duct

Removal

1.
Remove the two parking brake lever bracket to

dash brace attaching screws and move the lever and

cable so they will not interfere with the duct

removal.

2.
Remove the screw and lock washer attaching the duct

outer bracket to the hinge pillar support.

3.
Remove the screws and lock washers attaching the

duct assembly to the dash brace bracket.

4.
Carefully pull the outer end of the duct downward,

detaching the courtesy light from its bracket.

5. Loosen the screws clamping the outlet duct to dis-

tributor assembly flexible tubing at the outlet duct.

The outlet duct may now be removed from beneath

the instrument panel.

6. The duct extension assembly and the deflector as-

sembly may be removed, if desired, as seen in

Figure 95.

Installation

The duct assembly is installed by reversing the re-

moval instructions.

Center Outlet Duct

Removal

1.
Remove the right and left console trim panels.

2.
Remove the radio receiver.

3.
Remove the electric clock.
4.
Remove the knobs, nuts and bezels from the two

air conditioning controls above the clock, AIR COND.

PULL and COLD IN-HOT PULL.

5. Carefully pull the outlet duct and control cables

loose from the rear of the center console and work

it down and out from under the dash. The left hand

control cable runs through the left hand flexible

tubing and may be left in the tubing after it is dis-

engaged from the duct. The right hand control cable

must also be pulled from the duct assembly as the

duct is removed.

6. The center deflector barrel assembly may now be

removed if necessary. Snap off the hairpin clips to

remove the barrel and spacer washers.

Installation

Reverse the removal procedure for installation.

AIR DISTRIBUTOR ASSEMBLY

Removal

1.
Drain the cooling system radiator.

2.
Remove the heater hoses from the core pipes and

remove the cover attaching nuts and cover surround-

ing the core pipes.

3.
Remove the glove compartment assembly and the

glove compartment door.

NOTE:.
See "Section 1 - Body" for removal

and installation of body items.

4.
Remove the right kick pad.

5. Remove the right and left center console trim panels.

6. Remove the radio receiver assembly.

7. Remove the defroster duct.

CHEVROLET CHASSIS SERVICE MANUAL