overheating CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

REAR SUSPENSION AND DRIVE LINE 4-30

Fig.
76—Differential Gear Failure

Hypoid Gears

Hypoid gear tooth scoring (fig. 74) is caused generally

by improper break-in, incorrect lube, insufficient gear

backlash or improper 'ring/pinion gear alignment. The

scoring will progressively lead to complete erosion of

the gear tooth, or gear tooth pitting and eventual fracture

with possible attendant damage to bearings, if the initial
scoring condition is not diagnosed in time and corrected.

Hypoid gear scoring is easily recognized by its char-

acteristic loud whine in either drive, coast or under both

conditions. Another cause of hypoid tooth fracture (fig.

75) is extended overloading of the gear set which will

produce fatigue fracture, or shock loading which will

result in sudden failure.

Differential Gears

Common causes of differential gear failure are shock

loading, extended overloading leading to fatigue failure,

and overheating of gear thrust surfaces resulting from

excessive wheel spin and consequent lubrication break-

down. Overheating will lead to seizing of thrust surfaces

or tooth failure (fig. 76).

Bearings

• Failure of axle tapered roller bearings is due pri-

marily to excessive wear caused by long service or

foreign materials in the oil. The second most common

cause of bearing failure is too tight or too loose pre-

load adjustment leading to spalling and eventual failure.

This failure may also lead to hypoid gear scoring due to

the resultant misalignment of the hypoid gear set.

COMPONENT PARTS REPLACEMENT

(Chevrolet, Cheveile, Chevy II and Camaro)

AXLE ASSEMBLY

Removal

1.
Raise vehicle to a height that will permit axle as-

sembly to hang freely and position supports under

both frame side rails.

2.
Disconnect wheel cylinder inlet lines. Disconnect and

remove brake hose and brake line retaining bracket

by removing retaining bolt from carrier cover.

3.
Loosen parking brake equalizer adjusting nut and

disconnect both rear cables at frame bracket and at

control arms. See Section 5 for detail of parking

brake cable removal.

4.
Remove two trunnion bearing "U" bolts from the

rear yoke and separate rear universal joint. Wire

propeller shaft to frame side rail and tape trunnion

bearing cups.

5. Support arid secure axle assembly with an adjustable

lifting device. On Chevrolet and Cheveile models,

loosen upper and lower control arm attaching bolts

at axle housing. (On Chevrolet models, disconnect

tie rod at axle bracket.)

6. Disconnect shock absorbers at axle brackets. Refer

to Shock Absorber Removal procedures outlined in

this section.

7. On Chevrolet and Cheveile models, lower axle as-

sembly until suspension reaches end of travel, then

disconnect spring retainers and withdraw springs

from vehicle.

8. On Chevy II and Camaro models, remove four nuts

securing lower spring seat to axle housing, then

remove spring front eye bolts or spring attaching

bracket and swing spring to rear so that it does not

interfere with axle.

9. On Chevrolet and Cheveile models, disconnect upper

and lower control arm attaching bolts at axle housing*
10.
Lower axle assembly and remove from under vehicle.

Installation

1.
Place axle assembly under vehicle and raise into

position.

2.
On Chevrolet and Cheveile models, install, but do not

tighten, upper and lower control arm attaching bolts

at axle housing.

3.
On Chevrolet models, position coil springs in upper

seats so that end of spring is indexed in seat.

4.
On Chevrolet models, install lower end of spring on

axle bracket or control arm and secure by installing

retainer and bolt. Install lock washer and retainer

nut.

5. On Cheveile pry lower pigtail of spring over vertical

flange of the axle bracket spring seat.

6. On Chevy II and Camaro models, install spring seat

pads and swing springs up into spring seats on axle

housing, making sure upper seat pads are aligned in

axle housing bracket.

7. Install spring front eye bolt and tighten, then install

spring seat lower mounting bracket and retaining

nuts.

8. Raise axle assembly to allow shock absorber and tie

rod installation. Position shock absorber in axle

bracket. Torque nut as outlined in Shock Absorber

Installation procedures.

9. Install brake hose and brake line retaining bracket

to carrier and connect wheel cylinder inlet lines.

Connect parking brake cable to frame bracket and

at control arm. Adjust parking brake and bleed

brakes as outlined in Section 5.

10.
Reassemble rear universal joint to companion flange.

11.
Support vehicle at axle and remove supports from

beneath the frame side rails.

12.
Remove supports and lower vehicle to floor. Torque

all affected parts to specifications.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-33

O

V-8 ENGINE
STARTING MOTOR

Fig.
2s—V-8 Starting Circuit Diagram

2.

3.
From battery negative post
To
starting motor

housing.

From solenoid battery terminal
To
solenoid motor

terminal.

If voltage drop
in
any
of
above check exceeds 0.2 volts,

excessive resistance
is
indicated in that portion
of
start-

ing circuit
and the
cause
of the
excessive resistance

should
be
located
and
corrected
in
order to obtain maxi-

mum efficiency in the circuit.

CAUTION:
Do not
operate
the
starting motor

continuously
for
more than
30
seconds
to
avoid

overheating.

When
the
solenoid fails
to
pull
in, the
trouble may be

due
to
excessive voltage drop in the solenoid control cir-

cuit.
To
check
for
this condition, close
the
starting

switch
and
measure
the
voltage drop between
the
BAT-

TERY terminal of the solenoid and the
SWITCH (S)
termi-

nal
of
the solenoid.
1.
If
this voltage drop exceeds 3.5 volts, excessive
re-

sistance
in the
solenoid control circuit
is
indicated

and should be corrected.

2.
If the
voltage drop does not exceed 3.5 volts and the

solenoid does not pull in, measure the voltage availa-

ble
at
the SWITCH terminal
of
the solenoid.

3.
If the
solenoid does
not
feel warm,
it
should pull
in

whenever the voltage available
at
the SWITCH termi-

nal
is 7.7
volts
or
more. When
the
solenoid feels

warm,
it
will require
a
somewhat higher voltage
to

pull in.

STARTING MOTOR AND SOLENOID CHECK

The following checks
may be
made
if the
specific

gravity of the battery
is
1.215
or
higher.

1.
If the
solenoid does
not
pull in, measure the voltage

between
the
switch
(S)
terminal
of the
solenoid
and

ground with the starting switch closed.

CAUTION:
If the
solenoid feels warm, allow
to

cool before checking.

If
the
voltage
is
less than 7.7 volts, check for ex-

cessive resistance
in the
solenoid control circuit.

If
the
voltage exceeds 7.7 volts, remove the starting

motor
and
check
(1)
solenoid current draw,
(2)

starting motor pinion clearance,
and (3)
freedom of

shift lever linkage.

2.
If
the solenoid "chatters" but does not hold in, check

the solenoid
for an
open "hold-in" 'winding. When-

ever
it is
necessary
to
replace
a
starting motor

solenoid, always check starting motor pinion

clearance.

3.
If
motor engages
but
does
not
crank
or
cranks

slowly, check
for
excessive resistance
in the ex-

ternal starting circuit, trouble within
the
starting

motor,
or
excessive engine resistance
to
cranking.

SERVICE OPERATIONS

STARTING MOTOR

REMOVAL AND INSTALLATION (Fig.
3s)

The following procedure
is a
general guide
for all

vehicles
and
will vary slightly depending
on
series
and

model.

1.
Disconnect battery ground cable at battery.

2.
Raise vehicle
to a
good working height.

3.
Disconnect all wires
at
solenoid terminals.

NOTE: Reinstall
the
nuts
as
each wire
is
dis-

connected
as
thread size
is
different but may be

mixed and stripped.

4.
Loosen starter front bracket (nut on V-8 and bolt on

L-6) then remove two mount bolts.

5.
Remove
the
front bracket bolt
or nut and
rotate

bracket clear
of
work area then lower starter from

vehicle
by
lowering front end first
—
(hold starter

against bell housing
and
sort
of
roll end-over-end).

6. Reverse
the
removal procedure
to
install. Torque

the mount bolts
to
25-35
ft.
lbs. first, then torque

brace bolt.

7.
Check operation
of
starter on vehicle.
Fig.
3s—Starter Mounting

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-24

is at the full mark on the dip stick, it is just slightly be-

low the planetary gear unit. If additional oil is added,

bringing the oil level above the full mark, the planetary

unit will run in the oil, foaming and aerating the oil. This

aerated oil carried through the various oil pressure pas-

sages (low servo, reverse servo, clutch apply, converter,

etc.) may cause malfunction of the transmission assem-

bly, resulting in cavitation noise in the converter and

improper band or clutch application. Overheating may

also occur.

If the transmission is found consistently low on oil, a

thorough inspection should be made to find and correct

all external oil leaks.

PERIODIC OIL CHANGE

The transmission oil should be changed periodically as

recommended in Section 0, and whenever transmission is

to be removed from the vehicle for repairs.

1.
Run engine for one minute in neutral prior to chang-

ing.

2.
Be sure vehicle is level or raise from the rear only.

3.
Remove the oil pan drain plug and allow oil to drain

thoroughly into a pan or can.

Replace drain plug and refill with approximately two

quarts of oil specified in Section 0.

NOTE: To refill the transmission, remove dip

stick from oil filler tube and refill transmission

with oil specified in Section 0 using filler tube

and funnel J-4264. Then, after shifting into all

ranges at idle speed to fill all oil passages, the

engine should be run at 800-1000 rpm with the

transmission in Neutral until the oil warms up,

then add oil as required to raise the fluid level

to the full mark on the dip stick. Refill capacity

is approximately 2 qts.
4.

Fig.
1PG - Adjusting Low Band Using J-21848
PERIODIC LOW BAND ADJUSTMENT (Fig. 1PG)

Low band adjustment should be periodically performed

at 12,000 mile intervals, or sooner, as necessary if op-

erating performance indicates low band slippage.

1.
Raise vehicle and place selector lever in neutral.

2.
Remove protective cap from transmission adjusting

screw.

3.
a. On Corvette Models: Drop left exhaust pipe for

clearance.

b.
On Chevelle Models: To gain clearance between

underbody and transmission, it may be necessary

to remove rear mount bolts from crossmember,

and move transmission slightly toward passenger

side of vehicle. .

4.
Loosen adjusting screw lock nut 1/4 turn and hold in

this position with wrench.

5.
Using Special Tool J-21848 adjust band to 70 in. lbs.

and back off four (4) complete turns for a band which

has been in operation for 6,000 miles or more,.or

three (3) turns for one in use less than 6,000 miles.

CAUTION: Be sure to hold the adjusting screw

lock nut at 1/4 turn loose with a wrench during"

the.adjusting procedure.

6. Tighten the adjusting screw lock nut to specified

torque.

CAUTION: The amount of back-off is not an

approximate figure, it must be exact.

MANUAL SHIFT LINKAGE CHECK & ADJUST

(Column Type)

1.
The shift tube and lever assembly must be free in the

mast jacket. See Section 9 for alignment of steering

column assembly if necessary.

2.
To check for proper shift linkage adjustment, lift

the transmission selector lever towards the steering

wheel. Allow the selector lever to be positioned in

drive (D) by the transmission detent.

NOTE: Do not use the indicator pointer as a

reference to position the selected lever. When

performing linkage adjustment, pointer is ad-

justed last.

3.
Release the selector lever. The lever should be in-

hibited from engaging low range unless the lever is

lifted.

4.
Lift the selector lever towards the steering wheel,

and allow the lever to be positioned in neutral (N) by

the transmission detent.

5.
Release the selector lever. The lever should now

be inhibited from engaging reverse range unless the

lever is lifted.

6. A properly adjusted linkage will prevent the selector

lever from moving beyond both the neutral detent, and

the drive detent unless the lever is lifted to pass

over the mechanical stop in the steering column.

7.
In the event that an adjustment is required, place

the selector lever in drive (D) position as determined

by the transmission detent. See Steps 2 and 3.

8. Loosen the adjustment swivel at the cross-shaft,

and rotate the transmission lever so that it contacts

the drive stop in the steering column.

9. Tighten the swivel and recheck the adjustment. See

2 and 6.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-57

15.
Connect positive lead to battery terminal, lower hood

and test wiper and washer assembly for proper

operation.

WIPER TRANSMISSION

REMOVAL AND INSTALLATION

1.
Remove wiper block and arm assembly from trans-

mission.

2.
Remove glove box door and compartment assembly.

Refer to Section 1 for removal procedures.

3.
Remove three transmission-td-cowl retaining

screws.

4.
Remove wiper transmission retaining clip and re-

move transmission from crank arm. Then remove

transmission through the glove box opening.

5.
Reverse removal procedure to install wiper trans-

mission.

Fig.
94 - Wiper and Trans Installed

WIPER ASSEMBLY REPAIRS

The overhaul procedures for the wiper are broken down

into three major areas: The motor section, gear box

section and washer pump section. Each section may be

serviced independently of the other.

MOTOR SECTION

Disassembly

1.
Remove the two motor tie bolts.

2.
Remove the armature end-play adjusting screw (fig.

91).

3.
Strike the steel case lightly with a mallet to partiaUy

loosen it from the die casting housing and motor

field.

4.
Insert a tool through the armature adjusting screw

opening and push against the end of the armature

shaft to back off the case. This will retain the ar-

mature commutator in position between the brushes

until ready to separate the armature from the case.

5.
To separate armature from case while still retaining

the brush springs and brushes in place fashion a

spring similar to that shown in Figure 95 and insert

behind the brush leads as shown.
Fig.
95 - Retaining Armature Brushes

6. Pull the armature out of the case and remove the felt

washer, thrust plate, and rubber thrust disc from the

case assembly bearing as required.

7.
The field windings are pressed into the gear housing

and further disassembly is not recommended; how-

ever, the field leads may be unsoldered from the

brush holders to remove the case.

8. Clean and inspect all parts.

Inspect both the field and armature for damage

due to overheating such as unsoldered electrical

connections.

Check that brush leads are firmly attached both

to the brushes and their connections at the brush

holders.

Check brushes for wear. If brushes are worn to

within 3/16" of brush lead, or pigtail, they should be

replaced.

Check contacts of circuit breaker shown at top of

Figure 95. Clean as required or file lightly to re-

move irregularities.

Inspect all leads from the brush and circuit

breaker plate for worn insulation or tjreaks.

If it was determined by inspection that brush re-

placement was required, proceed as follows:

a. Remove retainer installed during disassembly and

remove brush springs.

b.
Place a hot soldering iron against*brush lead con-

nection on brush holders, remove old bushes, and

nection on brush holders, remove old brushes,

and install new brushes.

c. To reinstall brushes in holders, compress spring

within holder and hold fully compressed with a

thin instrument inserted through the slot in the

brush holder. Then push brush into holder with

lead upward to project through slot in holder, hold

CHEVROLET CHASSIS SERVICE MANUAL