steering Citroen BERLINGO MULTISPACE 2016 2.G Owner's Guide

Page 71 of 296

 69
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
Exceeding the programmed
speedSwitching the function offOperating fault
The programmed speed is cleared then
  replaced   by   three   dashes.
Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.
Flashing of the speed setting
Good practice
In  any   event,   the   speed   limiter   cannot  
replace the need to observe speed
limits,

  nor   can   it   replace   the   need   for  
vigilance

  on   the   part   of   the   driver.
Always
  pay   attention   to   the   profile  
of the road and sharp acceleration
and

  stay   in   complete   control   of   your  
vehicle.
T

o   avoid   any   jamming   under   the  
pedals:
-

 
ensure
  that   the   mat   and   its   fixings  
on

  the   floor   are   positioned   correctly,
-
 
never
  place   one   mat   on   top   of  
another

.
Pressing the accelerator pedal in order
to
 
exceed
 
the
 
programmed
 
speed
 
will have no ef

fect unless you press
the pedal firmly beyond the point of
resistance.
The
 
limiter
 
is
 
deactivated
 
temporarily
 
and

 
the
 
programmed
 
speed
 
flashes
 accompanied
 
by
 
an
 
audible
 
signal.
To
 
return
 
to
 
the
 
limiter
 
function,
 
reduce
 
your

 
speed
 
to
 
below
 
the
 
programmed
 
speed.
The

 
speed
 
setting
 
flashes:
-

following forcing of the accelerator
point of resistance,
-

 
when

 
the
 
limiter
 
cannot
 
prevent
 
an
 
increase in the vehicle speed due
to

 
the
 
profile
 
of
 
the
 
road
 
or
 
on
 
a
 
steep descent,
-

 
in

 
the
 
event
 
of
 
sharp
 
acceleration. -

Place the switch in position

0 or
switch off the ignition to switch the
system
 
off.
The
 
last
 
programmed
 
speed
 
remains
 
in
 
the

 
memory.
Steering mounted controls
EASE OF USE and COMFORT
4

Page 96 of 296

94
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
FRONT FITTINGS
1. Lower glove box
This may or may not be fitted with a lid.
Upper storage compartment
This is located on the dashboard,
behind  the   steering   wheel.
A
 

recess   makes   lifting   of   the   lid   easier  
when

  opening.   Guide   it   to   its   rest  
position.
T

o close, guide the lid then press the
centre
  gently.
Any
  liquid   which   could   spill   risks  
causing an electrical short circuit and
therefore

  a   potential   fire.
3. Side storage compartment
4. Bag hook
Only hang flexible bags which are not too  heavy   on   this   hook.
2. Storage pocket and bottle
holder (1.5 L)
Practical information

Page 116 of 296

11 4
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
HAZARD WARNING LAMPS
H
ORN
Press the centre of the steering wheel.
PARKING BRAKE
Applying
Pull the parking brake lever up to immobilise
  your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The
 
hazard
 
warning
 
lamps
 
should
 
only
 
be used in dangerous situations, when
stopping

 
in
 
an
 
emergency
 
or
 
when
 
driving

 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels

  towards   the   pavement   and   pull  
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated
  by   this   warning   lamp   which
 comes

  on   in   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the  hazard   warning   lamps   come  
on

  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It

  is   also   possible   to   switch   them   off   by  
pressing

  the   switch   on   the   dashboard.Releasing
Pull the lever up slightly and press the
button  to   lower   the   parking   brake   lever.
driving safely

Page 125 of 296

123
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
Operation
When your vehicle is too close to or
approaches the vehicle ahead too
quickly  the   system   automatically  
applies

  the   brakes   to   avoid   a   collision.
You are then alerted by the display of a
message.
The
  brake   lamps   on   your   vehicle   come  
on

  to   warn   other   road   users.
The collision can be avoided
automatically
  if   the   difference   in  
speed between your vehicle and the
vehicle

  ahead   does   not   exceed   9   mph  
(15 km/h).
Above

  this   threshold,   the   system   will  
do what is possible to avoid or reduce
the accident by lowering the speed of
impact.
The

  automatic   braking   may   bring  
the

  vehicle   to   a   complete   stop   if   the  
situation

  requires   it.
In this case, the vehicle is held
stationary
  temporarily   (for   about  
1.5 seconds)

  to   allow   the   driver   to   take  
back

  control   by   pressing   the   brake  
pedal. The

  triggering   of   the   system   may  cause the engine to stall, unless
the driver depresses the clutch
pedal
  quickly   enough   during   automatic  
braking.
During

  automatic   braking,   the  
driver can always obtain a higher
rate of deceleration than that
controlled

  by   the   system,   by   pressing  
firmly

  on   the   brake   pedal.
After
  an   impact,   the   system   is  
automatically

  put   out   of   service:   it  
no

  longer   operates.
You
  must   go   to   a   CITROËN   dealer   or   a  
qualified

  workshop   to   have   the   system  
made

  operational   again.
Operating limits
The system only detects vehicles that are  stationary   or   moving   in   the   same  
direction

  as   your   vehicle.
It
  does   not   detect   small   vehicles  
(bicycles,

  motorcycles),  
pedestrians

  or   animals,   nor   non-
reflective
  stationary   objects.
The
  system   is   not   triggered   or   is  
interrupted

  if   the   driver:
-

accelerates strongly
-


or turns the steering wheel
suddenly

  (avoiding   manoeuvre).
In
  difficult   weather   conditions   (very  
heavy

  rain,   snow,   fog,   hail...),  
braking

  distances   increase,   which  
can

  reduce   the   ability   of   the   system   to  
avoid

  a   collision.
The
  driver   must   therefore   remain  
particularly

  vigilant.
Never
  leave   accumulations   of  
snow

  or   any   object   projecting  
above the bonnet or in front of
the

  roof:   this   might   fall   into   the   field   of  
vision of the sensor and generate a
detection.
driving safely
SaFETY
5

Page 132 of 296

130
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
130
Advice
Sit  in   a   normal   upright   position.
Wear
  a   correctly   adjusted   seat   belt.
Do
 
not
 
allow
 
anything
 
to
 
come
 
between
 
the occupants and the airbags


(a
  child,   pet,   object...),   do   not   attach   or  
fix

  anything   near   to   the   airbags   or   their  
trajectories

  when   inflating   as   this   could  
cause

  injuries   when   the   airbags   are  
deployed.
Never

  modify   the   original   definition   of  
your vehicle, particularly in the area
directly

  around   the   airbags.
a

fter an accident or if the vehicle has
been
  stolen   or   broken   into,   have   the  
airbag

  systems   checked.
All
  work   on   the   airbag   system   must   be  
carried out by a CITR

o Ë n dealer or a
qualified
  workshop.
Even if all of the precautions
mentioned
  are   observed,   a   risk   of  
injury

  or   of   minor   burns   to   the   head,  
chest

  or   arms   when   an   airbag   is  
deployed

  cannot   be   ruled   out.  
The
  bag  
inflates

  almost   instantly   (within   a   few  
millis

econds)   then   deflates   within   the  
same

  time   discharging   the   hot   gas   via  
openings

  provided   for   this   purpose.Front airbags
d

o not drive holding the steering wheel
by
  its   spokes   or   resting   your   hands   on  
the

  centre   part   of   the   wheel.
Passengers
  must   not   place   their   feet  
on

  the   dashboard.
Do
  not   smoke   as   deployment   of   the  
airbags

  can   cause   burns   or   the   risk   of  
injury

  from   a   cigarette   or   pipe.
Never
  remove   or   pierce   the   steering  
wheel

  or   hit   it   violently.
Do
  not   fit   or   attach   anything   to   the  
steering wheel or dashboard, this could
cause

  injuries   with   deployment   of   the  
airbags.
Lateral airbags
Use only approved covers on the
seats,

  compatible   with   the   deployment  
the

  lateral   airbags.   For   information  
on the range of seat covers suitable
for your vehicle, you can contact a
CITROËN dealer

.
For
  more   information   on   accessories,  
refer to "

o ther accessories" in
section 6.
Do
  not   fix   or   attach   anything   to   the   seat  
backs

  (clothing...).  
This
  could   cause  
injury

  to   the   chest   or   arms   if   the   lateral  
airbag

  is   deployed.
d

o not sit with the upper part of the
body any nearer to the door than
necessary.
Airbags only operate when the
ignition is switched on.
This
 
equipment
 
only
 
operates
 
once.
 
If

 
a
 
second
 
impact
 
occurs
 
(during
 
the
 
same

 
or
 
a
 
subsequent
 
accident),
 
the
 
airbag

 
will
 
not
 
operate.
The
 
deployment

 
of

 
an

 
airbag

 
or

 
airbags

 
is

 
accompanied
 
by
 
a
 
slight
 
discharge
 
of

 
smoke
 
and
 
a
 
noise,
 
due
 
to
 
the
 
activation of the pyrotechnic cartridge
incorporated

 
in
 
the
 
system.
This
 
smoke
 
is
 
not
 
harmful,
 
but
 
sensitive

 
individuals
 
may
 
experience
 
some

 
irritation.
The
 
noise
 
of
 
the
 
detonation
 
may
 
result
 
in a slight loss of hearing for a short
time. The

 
passenger's
 
front
 
airbag
 
must
 
be deactivated if a child seat is
installed

 
rearward
 
facing.
Chapter
 
5,
 
"Child
 
safety"
 
section.
airbags

Page 134 of 296

132
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
132
Front airbags
Deployment
They are deployed, except the
passenger's front airbag if it has been
deactivated, in the event of a serious
front  impact   applied   to   all   or   part   of   the  
front

  impact   zone   A in the longitudinal
centreline of the vehicle on a horizontal
plane
  directed   from   the   front   towards  
the

  rear   of   the   vehicle.
The
  front   airbag   inflates   between   the  
front occupant of the vehicle and the
dashboard to cushion their forward
movement. Deactivating the passengers front
airbag
o

nly the passenger's front airbag can
be   deactivated.
-
W
ith the ignition switched off,
insert   the   key   into   the   passenger's  front
  airbag   deactivation   switch.
- T urn it to the "OFF"   position.
-
 
Remove
  the   key   keeping   the   switch  
in

  the   new   position.
The passenger's front airbag
warning
 
lamp
 
in
 
the
 
instrument panel

  remains   on   while   the
 airbag

  is   deactivated.If
  the   two   airbag   warning   lamps  
are on continuously

, do not install
a rearward facing child seat and
contact a CITR
o Ë n dealer or a
qualified
  workshop.
Front airbag fault
To ensure the safety of your child,
it is essential to deactivate the
passenger's front airbag when you
install a rearward facing child seat on
the
  front   passenger   seat.   Otherwise,  
the

  child   would   risk   being   killed   or  
seriously

  injured   if   the   airbag   were  
deployed.Reactivation
In the

"OFF" position, the passenger's
front airbag will not be deployed in the
event   of   an   impact.
As   soon   as   the   child   seat   is   removed,  
turn the passenger's front airbag switch
to the

"ON" position to reactivate the
airbag and thus ensure the safety
of your passenger in the event of an
impact.
If   this   warning   lamp   comes  
on,

  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, consult a
CITR

o Ë n dealer or a
qualified   workshop   to   have  the
  system   checked.
The
  front   airbags   are   fitted   in   the  
centre of the steering wheel for the
driver and in the dashboard for the
front

  passenger.
airbags

Page 154 of 296

152
Berlingo-2-VP_en_Chap06_accessoire_ed01-2016
Equipment
OTHER ACCESSORIES
These accessories and parts, having
been tested and approved for reliability
and safety, are all adapted to your
vehicle. 

wide   range   of   recommended  
accessories and genuine parts is
available.
a further range is also available,
structured

  around   comfort,   leisure   and  
maintenance:
Anti-theft

  alarm,   window   etching,   first  
aid

  kit,   high   visibility   vest,   front   and  
rear

  parking   sensors,   warning   triangle,  
security

  bolts   for   alloy   wheels, ...
Seat
  covers   compatible   with   airbags  
for the front seats, bench seat, rubber
mats,

 
carpet
 
mats,
 
snow
 
chains,
 
blinds,
 
tailgate

  bicycle   carrier,   ...
To
  prevent   the   mat   from   becoming  
caught

  under   the   pedals:
-
 
ensure
  that   the   mat   and   its   fixings  
are positioned correctly

,
-
 
never
  fit   one   mat   on   top   of   another.Audio
  equipment,   hands-free   kit, speakers,
  CD   changer,   satellite navigation

 
system,
 
USB
 
box,
 
V
ideo  
kit, 
...
Regardless
  of   the   audio   and   telematic
 equipment

  offered   on   the   market,   the
 technical constraints associated with


the
  fitting   of   equipment   of   these   product
 groups

  mean   that   the   special   features
 of

  the   equipment   and   its   compatibility
 with the capacities of your vehicle's


standard
  equipment   must   be   taken   into
 account.

  Please   ask   a   CITROËN   dealer
 for

  more   information   before   fitting   such
 equipment.
Maximum weights on bars
-


T
ransverse bars on longitudinal
bars:
  75   Kg   (these   bars   are   not  
compatible

  with   the   Modutop   roof).
Installing radiocommunication
transmitters
You are advised to contact a CITR
o Ë n
dealer before installing accessory
radiocommunication
  transmitters   with  
external

  aerial   on   your   vehicle.
The
  CITROËN dealer   network  
will

  inform   you   of   the   specification  
(frequency

  band,   maximum   output  
power

,   aerial   position,   specific  
conditions of installation) of the
transmitters

  which   can   be   fitted,   in  
accordance with the Motor V

ehicle
Electromagnetic
  Compatibility  
Directive (2004/104/EC).Front

  mud   flaps,   rear   mud   flaps,  15/17 inch
  alloy   wheels,   wheelarch  
trim,

  leather   steering   wheel,   ...
Screenwash, interior and exterior
cleaning
  and   maintenance   products,  
spare

  bulbs,   ...
The
  fitting   of   electrical   equipment  
or accessories which are not
recommended

  by   CITROËN   may  
result in a failure of your vehicle's
electronic

  system.   Please   note   this  
specific

  warning.  
Y
ou   are   advised  
to contact a dealer to be shown the
range

  of   recommended   equipment   or  
accessories.
d

epending on the country in which
the
  vehicle   is   sold,   it   is   compulsory  
to have a high visibility vest, warning
triangle and spare bulbs available in
the

  vehicle.

Page 157 of 296

155
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Under the bonnet
PETROL ENGINE
1. Screenwash   fluid   reservoir.
2.  
Fusebox.
3.

 
Engine
  coolant   header   tank.
Battery
  connections:
+
  Positive   terminal.
-
   Negative   point   (earth).
Take
  care   when   working   under   the   bonnet.
4.  Brake   and   clutch   fluid   reservoir.
5.  
Air
  filter.
6.
 
Engine
  oil   dipstick.7.
 Engine   oil   filler   cap.
8.  
Power
  steering   fluid   reservoir.
CHECkS
7

Page 158 of 296

156
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Under the bonnet
DIESEL ENGINE
4. Brake   and   clutch   fluid   reservoir.
5.  
Air
  filter.
6.
 
Engine
  oil   dipstick.
7.
 
Engine
  oil   filler   cap. 8.
 Power   steering   fluid   reservoir.
9.  
Priming
  pump
 (except

  BlueHDi   engines).
1.
 Screenwash
 
fluid
 
reservoir.
2.
 
Fusebox.
3.

 
Engine

 
coolant
 
header
 
tank.
Battery
  connections:
+
  Positive   terminal.
-
   Negative   point   (earth).
Take
 
care
 
when
 
working
 
under
 
the
 
bonnet.

Page 160 of 296

158
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Levels
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).

Page:   < prev 1-10 11-20 21-30 31-40 41-50 next >