battery Citroen BERLINGO MULTISPACE RHD 2016 2.G Owner's Guide

170
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
ECONOMY MODE
after the engine has stopped, with
the   key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows,
  courtesy   lamps,   audio  
equipment,

  etc.)   can   only   be   used   for   a  
cumulative

  duration   of   thirty   minutes,   to  
prevent

  discharging   of   the   battery.
Once
  the   thirty   minutes   have   elapsed,  
the active functions are put on standby
and

  the   battery   warning   lamp   flashes  
accompanied

  by   a   message   in   the  
screen.
T

o   resume   the   use   of   these   functions  
immediately

,   start   the   engine   and   let   it  
run

  for   a   few   minutes.
The
  time   available   will   then   be   double  
the

  time   for   which   the   engine   was   left  
running.

  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery

181
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
2. Sidelamps
T ype A, W5W - 5W
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-
 
Remove
  the   bulb   holder   fitted   by  
pressure

  by   pulling   the   connector.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
Front lamps
1. Dipped / Main beam headlamps
T ype C, H4 - 55W
-
 
Remove
  the   centre   cover   by   pulling  
the

  flexible   rubber   tab.
-
 
Disconnect
  the   electrical   connector.
-
 
Release
  the   retaining   tab.
-
 
Change
  the   bulb   taking   care  
to

  align   the   metal   part   with   the  
grooves

  on   the   lamp.
-
 
Reposition
  the   retaining   tab.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
High pressure washing Open

 
the
 
bonnet.
 
T

o
 
access
 
the
 
bulbs,
 
reach

 
behind
 
the
 
headlamp
 
unit.
Carry out the operations in reverse
order
 
to
 
refit
 
each
 
bulb
 
and
 
check
 
that
 
the

 
bonnet
 
is
 
closed
 
securely.
Halogen
 
bulbs
 
must
 
be
 
changed
 
with

 
the
 
headlamp
 
off.
 
Wait
 
a
 
few minutes

 
(risk
 
of
 
serious
 
burns).

 
Do
 
not
 
touch
 
the
 
bulb
 
directly
 
with

 
your
 
fingers,
 
use
 
a
 
lint-free
 
cloth.
It
 
is
 
normal
 
for
 
condensation
 
to
 
form
 
inside

 
the
 
headlamps.
 
Regular
 
use
 
of
 the
 
vehicle
 
eliminates
 
this
 
misting.
The
 
bulbs
 
must
 
be
 
changed
 
with
 
the ignition of

f or with the battery
disconnected.
 
Wait
 
approximately
 

3
 
minutes
 
after
 
changing
 
the
 
bulb
 
before

 
reconnecting
 
the
 
battery.
Check
 
that
 
the
 
lamps
 
operate
 
correctly
 
after

 
each
 
operation.
When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
lamps
 
and
 
their
 
edges

 
to
 
avoid
 
damaging
 
their
 
coating
 
and

 
seals.
QUICk HELP
8
Changing a bulb

186
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
CHANGING A FUSE
The fuseboxes are located:
-
in the lower dashboard on the

left-hand side (behind the cover),
-
 
under
  the   bonnet   (near   the   battery).
The
  information   given   concerns   only  
those fuses which can be changed by
the user using the tweezer

, located
behind the dashboard storage
compartment
  on   the   right-hand   side.  
For

  any   other   work,   visit   a   CITROËN  
dealer

  or   a   qualified   workshop.
Removing and fitting a fuse
Always replace a failed fuse with a
fuse of the same rating.
Motor
 
trade
 
technicians:
 
for
 
complete

 
information
 
on
 
the
 
fuses
 
and relays, refer to the "Repair
Manual"

 
diagrams
 
via
 
the
 
dealer
 
network.
CITR

o
Ë
n
will not accept responsibility
for the cost incurred in repairing
your vehicle or for rectifying the
malfunctions
 
resulting
 
from
 
the
 installation of accessories not
supplied
 
and
 
not
 
recommended
 
by
 
the
 
CITROËN

 
network
 
and
 
not
 
installed
 
in accordance with its instructions,
in

 
particular
 
when
 
the
 
combined
 
consumption

 
of
 
all
 
of
 
the
 
additional
 
equipment

 
connected
 
exceeds
 

10
 
milliamperes. Before replacing a fuse, the cause of
the
  incident   must   be   identified   and  
rectified.
●

 
Use
  the   tweezer.
Changing a fuse

Audio and Telematics
 267
Berlingo-2-VP_en_Chap10a_SMEGplus_ed02-2015
QUESTIONANSWER SOLUTION
There is a difference in
sound quality between the
different
  audio   sources. For
  optimum   sound   quality,   the   audio   settings   for   Volume,   Bass,  
T

reble, Equalizer and Loudness can be adapted to the different
sound
  sources,   which   may   result   in   audible   differences   when  
c

hanging
 s
ource. Check
  that   the   audio   settings   for   (Volume,   Bass,  
T

reble, Equalizer, Loudness) are adapted to the
sources
  listened   to.   It   is   advisable   to   set   the  
a

udio functions (Bass, Treble, Fr-Re balance,
Le-Ri
  balance)   to   the   middle   position,   select   the  
"

Linear",   musical   ambience   and   set   the   loudness  
c

orrection to the "Inactive" position in radio
mode.
With the engine off, the
system
  switches   off   after   a  
f

ew
 
minutes   of   use. When
  the   engine   is   switched   off,   the   system's   operating   time  
d

epends   on   the   state   of   charge   of   the   battery.
The
  switch-off   is   normal:   the   system   switches   to   economy   mode  
a

nd   switches   off   to   prevent   discharging   of   the   vehicle's   battery.Start the vehicle's engine to increase the battery
charge.
TECHNOLOGY on BOARD
10

Audio and Telematics
 269
Berlingo-2-VP_en_Chap10b_Rd45_ed02-2015
Audio system
Audio system / Bluetooth®
Contents
First
 
steps
 2 70
Steering
 
mounted
 
controls
 
2
71
Menus
 
2
72
Radio
 
2
72
M e d i a
 2

74
Telephone
 2

78
Screen
 
menu
 
map(s)
 
2
80
Frequently
 
asked
 
questions
 
2
84
Your
 
Audio
 
system
 
is
 
coded
 
in
 
such
 
a
 
way
 
that
 
it
 
will
 
only
 
operate
 
i

n
 
your
 
vehicle. As
 
a
 
safety
 
measure,
 
the
 
driver
 
must
 
only
 
carry
 
out
 
operations
 w

hich
 
require
 
prolonged
 
attention
 
while
 
the
 
vehicle
 
is
 
stationary.
When the engine is switched off and to prevent discharging of the
battery,
 
the
 
audio
 
equipment
 
may
 
switch
 
off
 
after
 
a
 
few
 
minutes.
TECHNOLOGY on BOARD
10

Audio and Telematics
284
Berlingo-2-VP_en_Chap10b_Rd45_ed02-2015
The table below gives answers to the most frequently asked questions on your audio system.
Q UESTION ANSWER SOLUTION
With the engine off, the
audio
  system   switches   off  
a

fter   a   few   minutes   of   use.When
  the   engine   is   switched   off,   the   audio   system   operating   time  
d

epends   on   the   state   of   charge   of   the   battery.
The
  switch-off   is   normal:   the   audio   equipment   switches   to   economy  
m

ode   and   switches   off   to   prevent   discharging   of   the   vehicle's  
b

attery. Start the vehicle's engine to increase the battery
charge.
The
  message   "the   audio  
s

ystem   is   overheated"  
a

ppears   on   the   display.In
  order   to   protect   the   installation   if   the   surrounding   temperature  
i

s   too   high,   the   audio   system   switches   to   an   automatic   thermal  
p

rotection   mode   leading   to   a   reduction   in   volume   or   CD   play  
s

topping. Switch
  the   audio   system   off   for   a   few   minutes   to  
a

llow   the   system   to   cool.
Frequently asked questions
QUESTIONANSWER SOLUTION
There is a difference in
sound quality between the
different audio sources
(radio,
 C

D...). For
  optimum   sound   quality,   the   audio   settings   (Volume,   Bass,  
T

reble,   Ambience,   Loudness)   can   be   adapted   to   the   different   sound  
s

ources,   which   may   result   in   audible   differences   when   changing  
s

ource   (radio,   CD...). Check
  that   the   audio   settings   (Volume,   Bass,  
T

reble,   Ambience,   Loudness)   are   adapted   to  
t

he   sources   listened   to.   It   is   advisable   to   set  
t

he audio functions (Bass, Treble, Front-Rear
Balance,
  Left-Right   Balance)   to   the   middle  
p

osition,   select   the   musical   ambience   "None"  
a

nd set the loudness correction to the "
ac
tive"
position
  in   CD   mode   or   to   the   "Inactive"   position  
i

n   radio   mode.
Radio

Audio and Telematics
286
Berlingo-2-VP_en_Chap10b_Rd45_ed02-2015
Media
QUESTIONANSWER SOLUTION
The
 
message   "USB  
p

eripheral error" is
displayed
  on   the   screen.
The Bluetooth connection
is
 
cut. The
  battery   of   the   peripheral   may   not   be   sufficiently   charged. Recharge   the   battery   of   the   peripheral   device.
The
  USB   memory   stick   is   not   recognised.
The
  USB   memory   stick   may   be   corrupt.Reformat
  the   USB   memory   stick.
The
 
CD   is   ejected  
a

utomatically   or   is   not  
p

layed
 
by   the   player. The C
d

is inserted upside down, is unplayable, does not contain
any
  audio   data   or   contains   an   audio   format   which   the   player   cannot  
p

l ay.
The
  CD   is   protected   by   an   anti-pirating   protection   system   which   is  
n

ot   recognised   by   the   audio   equipment.-
 
C
heck   that   the   CD   is   inserted   in   the   player  
t

he   right   way   up.
-
 
C
heck   the   condition   of   the   CD:   the   CD  
c

annot   be   played   if   it   is   too   damaged.
-
 
C
heck   the   content   in   the   case   of   a   recorded  
C

D:   consult   the   advice   in   the   "Audio"   section.
-
 
T
he   audio   equipment's   CD   player   does   not  
p

lay   DVDs.
-
d
u
e to their quality level, certain writeable
CDs
  will   not   be   played   by   the   audio   system.
The C
d

player sound is
p o o r. The
  CD   used   is   scratched   or   of   poor   quality.Insert
  good   quality   CDs   and   store   them   in  
sui

table
 c
onditions.
The
  audio   equipment   settings   (bass,   treble,   ambiences)   are  
un

suitable. Set the treble or bass level to 0, without selecting
an
 am

bience.
QUESTION ANSWER SOLUTION
I
 
am
 
unable   to   access   my  
v

oicemail. Few
  telephones   or   service   providers   allow   the   use   of   this   function.
Telephone