ignition CITROEN C1 2018 User Guide

43
C1_en_Chap02_ouvertures_ed01-2016
Opening
F Briefly  press   the   control   in   the   opening  d
irection   to   open   the   the   roof   in   stages.
or
F
 
P
ress   and   hold   the   control   in   the   opening  
d

irection,   until   the   manoeuvre   is   complete,  
t

o   open   the   roof   completely.
 P

ressing   again   stops   the   movement   of  
the
  roof.
Closing
F Briefly   press   the   control   in   the   closing  d
irection   to   open   the   the   roof   in   stages.
or
F
 
P
ress   and   hold   the   control   in   the   closing  
d

irection,   until   the   manoeuvre   is   complete,  
t

o close the roof to position 1 .
 P

ressing   again   stops   the   movement   of  
t

he roof.
F
 
T
o   close   the   roof   completely,   press   and  
h

old   the   control   (between   positions   1
and
  0)
  until   the   roof   locks   closed.
The
  closing   manoeuvre   of   the   roof  
c

ould   cause   serious   injuries:   take  
p

articular   care   with   children.
If
  the   roof   does   not   close   correctly:
-
 
c
heck   that   nothing   is   blocking   the   roof  
(

ignition
 o
ff),
-
 
r
epeat   the   closing   command   (with   the  
e

ngine
 r
unning).
If
  the   problem   persists,   contact   a   CITROËN  
d

ealer   or   a   qualified   workshop.
Operating fault
In the event of an electrical fault,
contact  a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Protection of the electric motors
used for opening and closing the
roof
Following repeated opening and closing of the roof,   the   electric   motors   may   become   too   warm  
a

nd   no   longer   allow   the   roof   to   be   opened   or  
c

losed.   Allow   the   motors   to   cool   down   with   no  
o

peration   of   the   roof   for   10   minutes.
2
Access

44
C1_en_Chap02_ouvertures_ed01-2016
An aero-acoustic deflector is available to improve   the   acoustic   comfort   of   occupants   of  
t

he   vehicle   in   certain   driving   conditions  
(high
  speed),   by   reducing   the   turbulence   in  
t

he   passenger   compartment   resulting   from   the  
d

isplacement   of   air.
On
  opening   the   roof,   the   aero-acoustic  
d

eflector   is   deployed.
On
  closing   the   roof,   the   deflector   folds   away  
au

tomatically.
Aero-acoustic deflector Precautions for use
Never place objects on the roof, w
hether   open   or   closed.
Never
  sit   on   or   place   objects   on   the  
t

ransverse roof support when the roof
is
  open. In
  the   event   of   prolonged   storage   of   the  v
ehicle   outside,   it   is   recommended   that  
t

he   roof   be   protected   with   a   cover.
To
  avoid   damaging   the   roof,   do  
n

ot   open   it   under   snowy   or   frosty  
c

onditions.
Never
  use   sharp   tools   to   remove   ice   or  
a

ccumulations   of   snow   on   the   roof.
To
  limit   the   creation   of   folds   in   the   roof  
f

abric,   it   is   recommended   that   the   roof  
n

ot   be   left   open   for   long   periods.
The
  vehicle's   air   conditioning   system  
s

hould   not   be   operated   while   the   roof  
i

s   open. It
  is   recommended   that   the   roof   be  
c

losed   when   the   vehicle   is   left   parked.
Even
  if   the   roof   is   closed,   it   is   prudent  
n

ot   to   leave   any   valuable   objects   inside  
t

he   vehicle.
When you leave the vehicle, switch off
the
  ignition   and   remove   the   key   (take  
t

he   electronic   key   with   you)   to   avoid   any  
u

nwanted   operation   of   the   roof.
Access

47
C1_en_Chap03_ergonomie-confort_ed01-2016
Ensure that no person or object prevents   the   seat   slide   from   returning   to  
it

s
 in
itial
 p
osition.
Check
  that   the   seat   belt   has   reeled   in  
c

orrectly   so   as   to   not   impede   access   for  
p

assengers   to   the   rear   seats.
Heated seat control Access to the rear seats
(3-door)
F Pull  this   control   toward   you   to   fold   the   seat  b
ack   and   move   the   seat   for ward.
When
  returning   the   seat   to   its   initial   position,  
g

uide   it   back   until   the   seat   and   backrest   lock  
i

nto   place.
With
 
the
 
engine
 
running,
 
the
 
front
 
seats
 
can
 
be
 h
eated s
eparately.
F
 
P

ress
 
the
 
control
 
switch.
 T

he
 
indicator
 
lamp
 
comes
 
on.
F
 
P

ressing
 
the
 
switch
 
again
 
stops
 
the
 
hea

ting.
The
 
temperature
 
is
 
controlled
 
automatically.
The
 
seat
 
heating
 
function
 
is
 
deactivated
 
about
 
t

wo
 
minutes
 
after
 
switching
 
off
 
the
 
ignition.
 
To
 
r

eactivate
 
it,
 
switch
 
the
 
ignition
 
on
 
and
 
press
 
t

he
 
control
 
switch
 
again. Switch
 
the
 
seat
 
heating
 
off
 
as
 
soon
 
a

s
 
it
 
is
 
no
 
longer
 
needed,
 
as
 
reducing
 
t

he
 
vehicle's
 
electrical
 
current
 
demand
 
r

educes
 
fuel
 
consumption.
3
Ease of use and comfort

71
C1_en_Chap04_conduite_ed01-2016
Starting - switching off the engine with the key
1. "LOCK "   position.  T
he   steering   column   is   unlocked.
2.
" AC

C"
  position.
 T

he   ancillaries   (audio   system,  
1

2V socket...)   can   be   used.
3.


"ON " position
 I

gnition   on.
4.
" S

TA R T"
  position.
 E

ngine
 s
tarting.
Ignition switch
For vehicle fitted with a manual gearbox:
F I nsert   the   key   in   the   ignition   switch.
F
 
T
urn   the   key   to   position   2.
F
 
U
nlock   the   steering   column,   by   turning   the  
w

heel   slightly.
F
 
F
ully   depress   the   clutch   pedal.
F
 
P
ut   the   gear   lever   into   neutral.
F
 
O
perate   the   starter   by   turning   the   key   to  
p

osition 4 (S TA R T ) .
F
 
O
nce   the   engine   is   running,   release  
t

he key.
 T

he   key   returns   automatically   to   position   3
(ON) .
Starting using the key
For vehicles fitted with an ETG gearbox:
F
 I nsert   the   key   in   the   ignition   switch.
F
 
T
urn   the   key   to   position   2.
F
 
U
nlock   the   steering   column,   by   turning   the  
w

heel   slightly.
F

P
ress and hold the brake pedal .
F
 
P
ut   the   gear   selector   into   position   N.
F
 
O
perate   the   starter   by   turning   the   key   to  
p

osition 4 (S TA R T ) .
F
 
O
nce   the   engine   is   running,   release  
t

he key.
 T

he   key   returns   automatically   to   position   3
(ON) .
If
 
you
 
use
 
the
 
ancillaries
 
for
 
a
 
prolonged
 
p

eriod
 
(key
 
in
 
position
 
2 or 3 ),
 
you
 
risk
 
d

ischarging
 
the
 
battery.
 
Starting
 
your
 
v

ehicle
 
will
 
then
 
no
 
longer
 
be
 
possible.
 
B

e aware.
Never
 
leave
 
the
 
engine
 
running
 
in
 
a

n
 
enclosed
 
area
 
without
 
adequate
 
v

entilation:
 in

ternal
 c

ombustion
 e

ngines
 
emit
 
toxic
 
exhaust
 
gases,
 
s

uch
 
as
 
carbon
 
monoxide.
 
Danger
 
of
 
i

ntoxication
 
and
 
death.
 
In
 
very
 
severe
 
w

inter
 
conditions
 
(temperatures
 
b

elow -23°C),
 
it
 
is
 
necessary
 
to
 
allow
 
t

he
 
engine
 
to
 
run
 
for
 
4
 
minutes
 
before
 
s

etting
 
off,
 
in
 
order
 
to
 
ensure
 
the
 
c

orrect
 
operation
 
and
 
durability
 
of
 
t

he
 
mechanical
 
components
 
of
 
your
 
v

ehicle,
 
the
 
engine
 
and
 
gearbox.
4
Driving

72
C1_en_Chap04_conduite_ed01-2016
If you use the ancillaries for a prolonged period,   the   vehicle   will   automatically  
s

witch to " OFF"
  mode   after   about  
20
 m

inutes.
Be aware
 

in   order   to   avoid   discharging  
t

he   battery.
Starting - switching off the engine 
w ith   the   Keyless   Entry   and   Starting  
system
Changing the mode of the
vehicle
With the electronic key inside the v
ehicle;   each   press   on   the   "S TA R T/
STOP " button, with no action on the
pedals,
  changes   the   vehicle's   mode:
F
 
F

irst
 
press   ("ACC "
  mode).
 T

he
 
ancillaries   (radio,   12V   socket...)   can   be  
u

sed.
F
 
S

econd   press   ("ON "
  mode).
 I

gnition   on.
F
 
T

hird
 
press   ("OFF "
  mode).
Avoid
 
attaching
 
heavy
 
objects
 
to
 
the
 k
ey,
 
which
 
would
 
weigh
 
down
 
on
 
its
 
b

lade
 
in
 
the
 
ignition
 
switch
 
and
 
could
 
c

ause
 
a
 
malfunction.
F
 
I

mmobilise
 
the
 
vehicle.
Switching off
F With
  a   manual   gearbox:   put   the   gear   lever  i
nto   neutral.
F
 
W
ith   an   ETG   gearbox:   place   the   selector   at  
p

osition N .
F
 
T
urn   the   key   towards   you   to   position   2 (ACC).
F

Press in and turn the key to position 1 (LOCK) .F Remove   the   key   from   the   ignition   switch.
F  T urn   the   steering   until   the   steering   column  
l

ocks.
Driving

73
C1_en_Chap04_conduite_ed01-2016
Starting using the
electronic key
With the first press on the "S TA R T/
STOP "
  button,   this   indicator   lamp f

lashes   slowly   in   the   instrument   panel.Depending
  on   the   ambient   temperature,  
e

ach   attempt   at   starting   can   take   up   to  
a

round   30   seconds.   During   this   period,  
d

o   not   press   the   "START/STOP " button
again,
  or   release   the   clutch   pedal   or  
b

rake   pedal   (depending   on   the   type   of  
g

earbox).
After
  this   period,   if   the   engine   has   not  
s

tarted,   press   the   "START/STOP "
button
  again   for   another   attempt   at  
s

tarting. If
  one   of   the   starting   conditions   is  
n

ot   met,   the   "Keyless   Entry   and  
S

tarting"   system   indicator   lamp   flashes  
i

n   the   instrument   panel.   In   some  
c

ircumstances,   it   is   necessary   to  
t

urn   the   steering   wheel   slightly   while  
p

ressing   the   "
START/STOP " button to
assist   unlocking   of   the   steering.
For vehicles fitted with a manual gearbox:
F
 
W

ith
 
the   electronic   key   inside   the   vehicle,  
p

ut
 
the   gear   lever   into   neutral   and   fully  
d

epress   the   clutch   pedal. The
  presence   of   the   electronic   key   in  t
he   vehicle   is   essential   for   switching  
o

n   the   ignition   and   starting   only.   Once  
t

he   engine   has   started,   make   sure   that  
t

he   electronic   key   remains   with   the  
v

ehicle   until   the   end   of   the   journey:  
o

ther wise   you   would   not   be   able   to   lock  
t

he vehicle.
F
 
P
ress   and   release   the   "S TA R T/
STOP "
  button.
This
  indicator   lamp   comes   on   in   the  
in

strument
 pan
el. For vehicles fitted with an ETG gearbox:
F
 
W
ith   the   electronic   key   inside   the   vehicle,  
p

ut   the   gear   selector   at   N   and   press   the  
b

rake
 ped
al.
This   indicator   lamp   comes   on   in   the  
in

strument
 pan
el.
F  
P
ress   and   release   the   "
S TA R T/
STOP "   button.
4
Driving

75
C1_en_Chap04_conduite_ed01-2016
Emergency switch-off
In the event of an emergency only, the engine can   be   switched   of   without   conditions.   To   do  
t

his,   press   for   more   than   2   seconds,   or   make  
a

  minimum   of   3   successive   presses   on   the  
"ST

ART/STOP "
  button.
In
  this   case   the   steering   column   locks   as   soon  
a

s   the   vehicle   stops.
Electronic key not
recognised
If the electronic key is no longer in the recognition   zone   when   driving   or   when   you  
(

later)   request   switching   off   the   engine,   there   is  
a

n   audible   signal   to   warn   you.
F
 
P
ress   for   more   than   2   seconds,  
o

r   make   a   minimum   of  
3 s

uccessive   presses   on   the  
"ST

ART/STOP" button if you
want
  to   force   switching   off   of   the  
e

ngine   (note that restarting
will not be possible without
the
key).
Electronic e ngine 
i

mmobiliser
This locks the engine management system as s
oon   as   the   ignition   has   been   switched   off   and  
t

herefore   prevents   starting   of   the   vehicle   by  
a

nyone   who   does   not   have   the   key.
The
  ignition   key   has   an   electronic   chip   which  
h

as   a   special   code.   When   the   ignition   is  
s

witched   on,   the   code   must   be   recognised   for  
s

tarting   to   be   possible.
In
  the   event   of   a   malfunction,   your   vehicle   will  
n

ot   start.
Contact
  a   CITROËN   dealer   or   a   qualified  
w

orkshop. Do
  not   make   any   modifications   to   the  
e

lectronic   immobiliser   system.
4
Driving

76
C1_en_Chap04_conduite_ed01-2016
Manual parking brake
Applying
F Pull  the   parking   brake   lever   up   to  i
mmobilise   your   vehicle.
When
  the   vehicle   is   being   driven,   if  
t

he   parking   brake   is   still   on   or   has  
n

ot   been   fully   released,   this   warning  
l

amp   comes   on   accompanied   by   an  
a

udible
 s
ignal.
Releasing
F Pull  the   parking   brake   lever   up   gently,  p
ress the release button then lower the
lever
 f

ully.
5-speed manual 
g
earbox
Engaging reverse
gear
F Press   the   clutch   pedal   fully   down.
F  P ush   the   gear   lever   fully   to   the   right   then  
ba

ckwards.
Only
  engage   reverse   gear   when   the
 v

ehicle   is   stationary   with   the   engine   at   idle.
When
 
parking
 
on
 
a
 
slope,
 
direct
 
your
 
w

heels
 
against
 
the
 
kerb,
 
apply
 
the
 
p

arking
 
brake,
 
switch
 
off
 
the
 
ignition
 
a

nd
 
engage
 
a
 
gear
 
(vehicles
 
fitted
 
with
 
a

 
manual
 
gearbox).
Driving

80
C1_en_Chap04_conduite_ed01-2016
The vehicle can be stopped whatever the position   of   the   gear   selector   (N , E or R ).
However,
  there   is   an   audible   signal   on   opening  
t

he   driver's   door   if   the   gear   selector   is   not   at  
p

osition N .
Switching off
When the vehicle is stopped with the e
ngine   running,   always   put   the   gear  
s

elector to neutral N .
There
  is   a   continuous   audible   signal  
i

f   you   turn   the   ignition   switch   to   "OFF "
with
  the   vehicle   in   2
nd, 3rd, 4th or 5th ge a r.
In
 
this
 
case
 
return
 
the
 
ignition
 
switch  
t

o " ON ",
 
move
 
the
 
gear
 
selector
 
to  
p

osition


N , then to position E , M or R,
then
 
turn
 
the
 
ignition
 
switch
 
to
 
" OFF ".
On
 
a
 
slope,
 
use
 
the
 
brakes
 
to
 
i

mmobilise
 
the
 
vehicle
 
and
 
place
 
the  
g

ear
 
selector
 
in
 
position
 
N , E or R . With
  the   ignition   on,   illumination  
o

f   this   warning   lamp   indicates   a  
g

earbox   fault.
Contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating faults
In all cases, it is essential
that you
apply the parking brake  to   immobilise  
t

he   vehicle.
Before
  doing   anything   under   the  
b

onnet,   check   that   the   gear   selector   is  
i

n neutral N   and   the   parking   brake   is  
a

pplied.
Limits of operation
On a gradient, or when hill start assist is activated, n ever hold the vehicle using the
accelerator :
  you   could   damage   the   clutch.
In
  these   situations   there   is   an   audible   signal.
F
 
M
ove   the   gear   selector   to   position   N.
F
 
W
ait   15   minutes   to   allow   the   clutch   to   cool  
d

own   before   setting   off. -
 
c
heck   that   the   ignition   switch   is   at   the  
"
O
N
"

position,
-  
p
lace   the   gear   selector   at   N
,   then   move   it  
t

o E
, M or R .
If 1   is   flashing   in   the   instrument   panel:
-  p lace   the   gear   selector   at   E or M
, then
move   it   to   N.
If R
  is   flashing   in   the   instrument   panel:
-
 
p
lace   the   gear   selector   at   R,
  then   move   it  
t

o N.
If
N is   flashing   in   the   instrument   panel
 a

ccompanied   by   an   audible   signal   for   a   long   time:
Driving

86
C1_en_Chap04_conduite_ed01-2016
The speed limiter cannot, in any circumstances,   replace   the   need   to o

bserve   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.
Speed limiter (PureTech 82 engine)
The speed limiter is switched on  manually: t
his   can   be   done   whatever   the   speed   of   the  
v

ehicle.   However,   if   you   are   driving   at   less   than  
2

0   mph   (30   km/h),   the   programmed   speed   will  
b

e   fixed   at   20   mph   (30   km/h).
The
  speed   limiter   is   paused by operation of the
control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly  
b

eyond   the   point   of   resistance.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal   until   the   vehicle  
r

eturns   to   the   programmed   speed   limit.
System
  which   prevents   the   vehicle   from   exceeding   the   speed   programmed   by   the   driver.Steering mounted controls
The controls are grouped together on this c
ontrol   stalk   at   the   steering   wheel.
1.
 S

peed   limiter   on   /   off:   by   pressing   the   end  
o

f   the   control   stalk.
2.
 D

ecrease   the   setting:   by   pushing   the  
c

ontrol   stalk   down.
3.
 I

ncrease   the   setting:   by   pushing   the   control  
s

talk   up.
4.
 S

peed   limiter   on   /   pause:   by   pulling   the  
c

ontrol   stalk   towards   you.
Displays in the instrument panel
The information is grouped together in the instrument   panel   screen.
5.
 S

peed   limiter   mode   selection   indication.
6.
 S

peed   limiter   on   /   pause   indication.
7.
 S

peed   value   setting.
The
 
programmed
 
speed
 
remains
 
in
 
the
 m

emory
 
when
 
the
 
ignition
 
is
 
switched
 
off.
Driving