Citroen C4 CACTUS 2015 1.G Owner's Manual

199
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Do not apply excessive force on the tab   as   locking   will   not   be   possible   if   the  
c

lamp   is   not   positioned   correctly;   start  
t

he   procedure   again.
Disconnecting the (+) cable
F Raise  the   locking   tab   D fully to release the
cable t erminal c lamp E.
Reconnecting the (+) cable
F Position   the   open   clamp   E of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   vertically   on   the   clamp   E to position
it
  correctly   on   the   battery.
F
 
L
ock   the   clamp   by   spreading   the  
p

ositioning   lug   and   then   lowering   the   tab   D.
9
Practical information

200
C4-cactus_en_Chap09_info-pratiques_ed02-2014
When your vehicle's battery is discharged, the engine   can   be   started   using   a   slave   battery  
(

external   or   on   another   vehicle)   and   jump   lead  
c

ables.
Starting using another
battery
F Operate   the   starter   on   the   broken   down  v
ehicle   and   let   the   engine   run.
 I

f   the   engine   does   not   start   straight   away,  
s

witch   off   the   ignition   and   wait   a   few  
m

oments   before   trying   again.
F
 
R

emove
 
the
 
plastic
 
cover
 
from
 

the
 
(+)
 
terminal,
 
if
 
your
 
vehicle
 
has
 
one.
F

C

onnect the red cable to the positive
terminal
 
(+)
 
of
 
the
 
flat
 
battery
 
A
, then to the
positive
 
terminal
 
(+)
 
of
 
the
 
slave
 
battery
 
B.
F
 
C

onnect
 
one
 
end
 
of
 
the
 
green
 
or
 
black
 
c

able
 
to
 
the
 
negative
 
terminal
 
(-)
 
of
 
the
 
s

lave battery B
 
(or
 
earth
 
point
 
on
 
the
 
other
 
v

ehicle).
F
 
C

onnect
 
t

he
 
o

ther
 
e

nd
 
o

f
 
t

he
 
g

reen
 
o

r
 
b

lack
 
c

able to the earth point C
 
on
 
the
 
broken
 
d

own
 
vehicle
 
(or
 
on
 
the
 
engine
 
mounting).
F
 
S

tart
 
the
 
engine
 
of
 
the
 
vehicle
 
with
 
the
 
g

ood
 
battery
 
and
 
leave
 
it
 
running
 
for
 
a
 
f

ew minutes. First
 
check
 
that
 
the
 
slave
 
battery
 
has
 
a
 
n

ominal
 
voltage
 
of
 
12
 
V
 
and
 
a
 
capacity
 
a

t
 
least
 
equal
 
to
 
that
 
of
 
the
 
discharged
 
b

attery.
Do
 
not
 
try
 
to
 
start
 
the
 
engine
 
by
 
c

onnecting
 
a
 
battery
 
charger.
Do
 
not
 
disconnect
 
the
 
(+)
 
terminal
 
when
 
t

he
 
engine
 
is
 
running.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition b
efore   disconnecting   the   battery.
Close the windows and the doors before
disconnecting
  the   battery.
Following reconnection of
the battery
Following reconnection of the battery, switch on t
he   ignition   and   wait   1   minute   before   starting   to  
p

ermit   initialisation   of   the   electronic   systems.  
H

owever,   if   problems   remain   following   this  
o

peration, contact a CITR
oËn
dealer or a
qualified
 w

orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust
 y
ourself
 r
einitialise
 (
depending
 o
n
 ve

rsion):
-
 
t
he   remote   control   key,
-
 ...
F

 
W

ait
 
until
 
the
 
engine
 
returns
 
to
 
idle
 
then
 
d

isconnect
 
the
 
jump
 
lead
 
cables
 
in
 
the
 
r

everse
 o

rder.
F
 
R

efit
 
the
 
plastic
 
cover
 
to
 
the
 
(+)
 
terminal,
 
if
 
y

our
 
vehicle
 
has
 
one.
Practical information

201
C4-cactus_en_Chap09_info-pratiques_ed02-2014
The batteries contain harmful substances such   as   sulphuric   acid   and   lead.   They m

ust   be   disposed   of   in   accordance
 w

ith   regulations   and   must   not,   in   any
 c

ircumstances,   be   discarded   with   household
 w

aste.
Take
  used   remote   control   batteries   and
 v

ehicle   batteries   to   a   special   collection   point.Protect your eyes and face before
handling  the   battery.
All
  operations   on   the   battery   must   be  
c

arried out in a well ventilated area and
away
  from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   or   fire.
Do
  not   try   to   charge   a   frozen   battery;  
t

he   battery   must   first   be   thawed   out   to  
a

void   the   risk   of   explosion.   If   the   battery  
h

as   been   frozen,   before   charging   have  
i

t   checked   by   a   CITROËN   dealer   or   a  
q

ualified   workshop   who   will   check   that  
t

he   internal   components   have   not   been  
d

amaged   and   the   casing   is   not   cracked,  
w

hich   could   cause   a   leak   of   toxic   and  
c

orrosive   acid.
do n

ot reverse the polarity and use only
a
  12   V   charger.
Do
  not   disconnect   the   terminals   while  
t

he   engine   is   running.
Do
  not   charge   the   batteries   without  
d

isconnecting   the   terminals   first.
Wash
  your   hands   after wards.
It is advisable to disconnect the battery
if the vehicle is to be left unused for
more
 
than
 
one
 
month.
If your vehicle is fitted with an electronic
gearbox,
  do   not   push   the   vehicle   to   start  
t

he
 eng
ine.Charging the battery using
a battery charger
F Disconnect   the   battery   from   the   vehicle.
F F ollow the instructions for use provided by
the
  manufacturer   of   the   charger.
F
 
C
onnect   the   battery   starting   with   the  
n

egative   terminal   (-).
F
 
C
heck   that   the   terminals   and   connectors  
a

re   clean.   If   they   are   covered   with   sulphate  
(

whitish   or   greenish   deposit),   remove   them  
a

nd   clean   them.
With Stop & Start, the battery does not
have
  to   be   disconnected   for   charging.
9
Practical information

202
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Load reduction mode
System which manages the use of certain functions   according   to   the   level   of   charge  
r

emaining   in   the   battery.
When
  the   vehicle   is   being   driven,   the   load  
r

eduction   function   temporarily   deactivates  
c

ertain   functions,   such   as   the   air   conditioning,  
t

he   heated   rear   screen...
The deactivated functions are reactivated
automatically
  as   soon   as   conditions   permit.System
  which   manages   the   duration   of   use   of  c
ertain functions to conserve a sufficient level
of
  charge   in   the   battery.
After
  the   engine   has   stopped,   you   can  
s

till use functions such as the audio and
telematics
  system, windscreen   wipers,   dipped  
b

eam   headlamps, courtesy   lamps,   etc.   for  
a

  maximum   combined   duration   of   about  
f

orty minutes.
Energy economy mode
Switching to economy mode
A message then appears in the instrument p
anel   screen   indicating   that   the   vehicle   has  
s

witched   to   economy   mode   and   the   active  
f

unctions   are   put   on   standby.
If
  a   telephone   call   is   being   made   at   this   time,  
i

t   will   be   maintained   for   around   10   minutes  
w

ith   the   Bluetooth   hands-free   system   of   your  
a

udio system.
Exiting economy mode
These functions are reactivated automatically n ext   time   the   vehicle   is   driven.
In order to restore the use of these functions
immediately,
  start   the   engine   and   let   it   run:
-
 
f
or   less   than   ten   minutes,   to   use   the  
e

quipment   for   approximately   five   minutes,
-
 
f
or   more   than   ten   minutes,   to   use   the  
e

quipment   for   up   to   approximately  
t

hirty minutes.
Let
  the   engine   run   for   the   duration   specified   to  
e

nsure   that   the   battery   charge   is   sufficient.
do n

ot repeatedly and continuously restart the
engine
  in   order   to   charge   the   battery.
A
  flat   battery   prevents   the   engine   from  
s

tarting   (refer   to   the   "Battery"   section).
Practical information

203
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Changing a wiper blade
F Within  one   minute   after   switching   off  t
he   ignition,   operate   the   wiper   stalk   to  
p

osition the wiper blades vertically on the
windscreen.
Removing
F Raise   the   corresponding   wiper   arm.
F P ull the screenwash delivery pipe to
disconnect
  it   from   the   jet   (located   on   the  
w

iper   blade).
F
 
U
nclip   the   wiper   blade   and   remove   it.
Fitting
F Put  the   corresponding   new   wiper   blade   in  p
lace   and   clip   it.
F

C
onnect the screenwash delivery pipe to
the
  jet   on   the   wiper   blade.
F
 
F
old   down   the   wiper   arm   carefully.
After fitting a front wiper
blade
F Switch  on   the   ignition.
F  O perate   the   wiper   stalk   again   to   park   the  
w

iper   blades.
Before removing a front
wiper blade
9
Practical information

204
C4-cactus_en_Chap09_info-pratiques_ed02-2014
To w i n g
General recommendations
Observe the legislation in force in your country.
E nsure   that   the   weight   of   the   towing   vehicle   is   higher   than   that   of   the   towed   vehicle.
The
  driver   must   remain   at   the   wheel   of   the   towed   vehicle   and   must   have   a   valid   driving   licence.
When
  towing   a   vehicle   with   all   four   wheels   on   the   ground,   always   use   an   approved   towing   arm;
 r

ope   and   straps   are   prohibited.
The
  towing   vehicle   must   move   off   gently.
When
  towing   a   vehicle   with   the   engine   off,   there   is   no   longer   any   power   assistance   for   braking
 o

r   steering.
In
  the   following   cases,   you   must   always   call   on   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or   fast   road,
-
f

our-wheel drive vehicle,
-
 
w
hen   it   is   not   possible   to   put   the   gearbox   into   neutral,   unlock   the   steering,   or   release   the
 par

king
 b
rake,
-
 
t
owing   with   only   two   wheels   on   the   ground,
-
 
w
here   there   is   no   approved   towing   arm   available...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed
 
or
 
for
 
towing
 
another   vehicle   using   a   removable   towing   eye.
The towing eye is stowed under the boot floor,
or
 
may
 
be
 
located
 
under
 
the
 
front
 
passenger
 sea
t, d
epending o
n v
ersion.
Practical information

205
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Towing another vehicle
F On  the   rear   bumper,   press   the   bottom   of  t
he   cover   to   unclip   it.
F
 
S
crew   the   towing   eye   in   fully.
F
 
I
nstall   a   towing   arm.
F
 
S
witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F
 
M
ove   off   gently   and   drive   slowly   over   a  
s

hort   distance   only.
F
 O
n
 
the
 
front
 
bumper,
 
press
 
at
 
the
 
bottom
 
of
 t
he
 
cover
 
to
 
unclip
 
it.
F
 
S

crew
 
the
 
towing
 
eye
 
in
 
fully.
F
 
I

nstall
 
a
 
towing
 
arm.
F
 
P

ut
 
the
 
gear
 
lever
 
into
 
neutral
 
(control
 
N for
an
 
electronic
 
gearbox).
Towing the vehicle
Failure to follow this instruction could
lead   to   damage   to   certain   components  
(

brakes,   transmission,   ...)   and   the  
a

bsence   of   braking   assistance   on  
r

estarting   the   engine. F
 
U
nlock   the   steering   by   turning   the   ignition  
k

ey   one   notch   and   release   the   parking  
b

rake.
F  
S
witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F  
M
ove   off   gently   and   drive   slowly   over   a  
s

hort   distance   only.
9
Practical information

206
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Towing a trailer
We recommend the use of genuine CITRoËn towbars and their harnesses
that have been tested and approved
from
  the   design   stage   of   your   vehicle,  
a

nd   that   the   fitting   of   the   towbar   is  
e

ntrusted to a CITR
oËn
dealer or a
qualified
 w

orkshop.
If the towbar is not fitted by a
CITROËN
  dealer,   it   must   still   be  
f

itted in accordance with the vehicle
manufacturer's
 i

nstructions.
Your
 
vehicle
 
is
 
primarily
 
designed
 
for
 t
ransporting
 
people
 
and
 
luggage,
 
but
 
it
 
may
 
a

lso
 
be
 
used
 
for
 
towing
 
a
 
trailer. Driving
  with   a   trailer   places   greater  d
emands   on   the   towing   vehicle   and   the  
d

river   must   take   particular   care.
Practical information

207
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Driving advice
Distribution of loads
F distribute the load in the trailer so that the heaviest   items   are   as   close   as  
p

ossible   to   the   axle   and   the   nose   weight  
a

pproaches   the   maximum   permitted  
w

ithout   exceeding   it.
ai

r density decreases with altitude, thus
reducing
  engine   per formance.   Above  
1 0

00 metres,   the   maximum   towed   load   must  
b

e   reduced   by   10 %   for   every   1 000   metres   of  
al

titude.
Side wind
F Take   into   account   the   increased   sensitivity  t
o   side   wind.
Cooling
Towing a trailer on a slope increases the temperature   of   the   coolant.
As
  the   fan   is   electrically   controlled,   its   cooling  
c

apacity   is   not   dependent   on   the   engine   speed.
F
 
T
o   lower   the   engine   speed,   reduce   your  
s

peed.
The
  maximum   towed   load   on   a   long   incline  
d

epends   on   the   gradient   and   the   ambient  
t

emperature.
In
  all   cases,   keep   a   check   on   the   coolant  
t

emperature. F
 
I
f   the   warning   lamp   and   the  
S

TOP
 
warning   lamp   come   on,  
s

top the vehicle and switch off
the
  engine   as   soon   as   possible.
Braking
Towing a trailer increases the braking distance.
T o   avoid   overheating   of   the   brakes   on   a   long  
m

ountain   type   of   descent,   the   use   of   engine  
b

raking   is   recommended.
Ty r e s
F Check   the   tyre   pressures   of   the   towing  v
ehicle   and   of   the   trailer,   observing   the  
re

commended
 p
ressures.
Lighting
F Check  the   electrical   lighting   and   signalling  o
n   the   trailer.
Refer to the "Technical data" section for details
of
 
the
 
weights
 
and
 
towed
 
loads
 
which
 
apply
 
to
 
y

our
 
vehicle.
When
 
not
 
towing
 
a
 
trailer,
 
remove
 
the
 
q

uickly-detachable
 
tow
 
ball
 
before
 
d

riving. The
  rear   parking   sensors   will   be  
d

eactivated   automatically   if   a   genuine  
C

ITROËN   towbar   is   used.
9
Practical information

208
C4-cactus_en_Chap09_info-pratiques_ed02-2014
Roof bars
For safety reasons and to avoid
damaging  the   roof,   it   is   essential   to   use  
t

ransverse roof bars that are approved
for
  your   vehicle.
Observe
  the   fitting   instructions   and  
t

he   conditions   of   use   given   in   the  
i

nformation   provided   with   the   roof   bars.Version without longitudinal
bars
To install the roof bars, you must secure them   only   to   the   four   anchorage   points   in   the  
r

oof   frame.   These   points   are   masked   by   the  
v

ehicle's   doors   when   closed.
The
  roof   bar   fixings   include   a   stud   that   should  
b

e introduced into the aperture at each
anchorage
 p

oint.
Version with longitudinal
bars
You must fit the transverse bars to the longitudinal   bars   at   the   fixing   points   indicated  
b

y   engraved   markings   on   the   longitudinal   bars.
Practical information