display Citroen C4 DAG 2008.5 1.G User Guide

29
I
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator zero reset Engine oil level indicator
After each service, the maintenance
indicator must be reset to zero.
Your CITROËN technician resets the
indicator to zero after each service.
However, if you do your own serv-
icing, the procedure for resetting to
zero is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL --" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
cate the dipstick and the oil fi ller cap
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.

30
I
I N S T R U M E N T S a n d C O N T R O L S
Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver's door is opened and when
the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
until it is reset to zero by the driver.

 With the ignition on, press the
button until zeros appear. Dashboard lighting rheostat
Activation

 Turn control A or press control B
to adjust the brightness of the
dashboard lighting,

 With control B , press until the
brightness is at maximum, release,
press until you reach minimum.
Deactivation
When the lights are off, or in day
mode in the case of vehicles fi tted
with daytime running lights, the but-
ton has no effect.
System permitting manual adjust-
ment of the brightness of the dash-
board to suit the level of ambient
light.
The rheostat is active if the sidela-
mps are on and applies to:
- the instrument panel,
- the display screens.

31
II
M U L T I F U N C T I O N D I S P L A Y S
MULTIFUNCTION SCREEN A
Presentation

1. Time

2. Date and display zone

3. Ambient temperature
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (ice risk).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
The display of certain types of in-
formation is sometimes by scrolling
and sometimes by alternating be-
tween them.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Confi rmation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed in zone 2
(date, radio-CD and trip recorder)

B or F. Within the menus, choice
of activation/deactivation of
functions and selection of
adjustments By pressing button
A , then using
button B , you have access to the fol-
lowing functions:

33
II
M U L T I F U N C T I O N D I S P L A Y S
MULTIFUNCTION SCREEN C Main Menu
Presentation
Radio-CD
(see "Audio")
Trip computer
This permits:
Bluetooth
®

hands-free kit
(see "Audio")
Controls

1. Time

2. Ambient temperature

3. Date and display zone
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (ice risk).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Confi rmation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen (See
"Trip computer") Press button
A to view the "Main
Menu" of the multifunction screen.
This menu gives you access to the
following functions:
- entering the distance to your destination,
- access to the log of alerts (recall of alerts signalled previously),
- access to the status of functions, such as the activation/deactiva-
tion of the automatic headlamps,
of the automatic windscreen wip-
ers, of the ESP...

36
II
M U L T I F U N C T I O N D I S P L A Y S
NAVIDRIVE MULTIFUNCTION COLOUR SCREEN
Presentation

1. Outside temperature

2. Directory

3. Date

4. Telephone

5. Time
When the outside temperature is be-
tween +3 °C and -3 °C, the tempera-
ture display fl ashes (ice risk).
The outside temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion. Controls
Main Menu

Traffi c Information

Navigation/Guidance

Map

Audio Functions

Telematics

Confi guration,
for adjusting various param-
eters (date, time, units)

Video

Vehicle Diagnostics

A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Confi rmation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen Press on the button
A to view the
"Main Menu" of the multifunction
screen.
This menu gives you access to the
following functions (see "NaviDrive
Instructions"):

37
II
M U L T I F U N C T I O N D I S P L A Y S
TRIP COMPUTER
System which provides current
information concerning the route
travelled (range, consumption...).
Monochrome screen A Data displays

 Press the control for more than
two seconds to reset to zero the
distance travelled, the average
consumption and the average
speed.
Zero reset
The trip computer provides the fol-
lowing information:
- range,
- current consumption,
- distance travelled,
- average consumption,
- average speed.

 The next press then returns you
to the normal display.

 Press the button, located at the
end of the wiper
stalk , to display
the various items of trip compu-
ter data in succession.

38
II
M U L T I F U N C T I O N D I S P L A Y S
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, consumption, …).
Monochrome screen C
NaviDrive colour screen Display of information
Trip zero reset

 Press the button, located at the
end of the wiper
stalk , to display
the various trip computer infor-
mation groups in succession:
- the current information group with:

38
II
M U L T I F U N C T I O N D I S P L A Y S
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, consumption, …).
Monochrome screen C
NaviDrive colour screen Display of information
Trip zero reset

 Press the button, located at the
end of the wiper
stalk , to display
the various trip computer infor-
mation groups in succession:
- the current information group with:

45
III
C O M F O R T
AUTOMATIC AIR CONDITIONING 1 - Automatic operation
This system automatically regulates
temperature, air fl ow and air distribu-
tion in the passenger compartment
according to the temperature select-
ed (for each side, right and left).
It provides an optimum level of
comfort regardless of the climatic
conditions, by permanent use of
the automatic air conditioning mode
(press the AUTO button ) and with

all the vents open.
Having no airfl ow prevents the air
conditioning and the system in gen-
eral from working.

To prevent misting of the interior
of the vehicle in cold and damp
conditions, the use of AUTO
mode is recommended. 2 - Adjustment of
temperature on left
hand side
To set and display the de-
sired temperature, rotate
control 2 or 3 :
The display HI (high) corre-
sponds to a demand for max-
imum heating (above 27).
The display LO (low) cor-
responds to a demand for
maximum air conditioning
(below 15).
3 - Adjustment of
temperature on right
hand side
- To the left to lower the temperature
-
To the right to raise the temperature
The difference between the tem-
peratures on the right and on the left
cannot be greater than 3 degrees.
A setting around 21 will provide a
temperature that is comfortable.
Depending on your requirements,
an adjustment between 18 and 24 is
normal.
A press on this control,
confi rmed by the display of
"A/C"
and "AUTO" , auto-
matically manages all the
5 following functions according to
the temperature chosen:
- Flow of air.
- Cabin temperature.
- Distribution of air.
- Air conditioning.
- Recycling of air.
To enable the system to operate, all
the air vents should be kept open. This is the normal operating
mode.

46
III
C O M F O R T

 When you enter the vehicle, the
temperature inside the vehicle
may be much colder (or warmer)
than a comfortable temperature.
There is no point in modifying
the displayed temperature to
try to attain the desired level of
comfort. The system operates
automatically to compensate this
temperature discrepancy as rap-
idly as possible.

 When starting the engine from
cold, in order to avoid distribut-
ing too much cold air, the blower
will attain its optimum level grad-
ually.

Manual
operation
of one or more
functions
Each of the functions 4 , 6 and 7 can
be adjusted manually.
Display of the "AUTO" function then
disappears.

Central and lateral air
vents.

Central and lateral air
vents and passenger
footwells.

Passenger footwells.

The windscreen, front
side windows and
passenger footwells.

The windscreen and
front side windows.
4 - Air conditioning
6 - Adjustment of the air
distribution
5 - Air recirculation To stop the air conditioning,
press on the control
4 . The
symbol "A/C" disappears.
To restart it, press again on
the control 4 . The symbol "A/C" dis-
plays.
When you press on control

5 , the entry of air from out-
side is blocked off and the
associated symbol is dis-
played.
This function can also be accessed
by pressing the appropriate button
on the steering wheel.
While retaining the other settings,
this position excludes disagreeable
odours or emissions coming from
outside. It should be cancelled as
soon as possible to prevent misting
and to allow fresh air into the cabin.
To deactivate the air recirculation,
press again on control 5 . Press the button
6 succes-
sively so that the multifunc-
tion screen shows, in turn,
the air fl ow to: